Porter-Cable FRP350 инструкция обслуживания

Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. _______________________________________ IMPORTANT Please make certain tha[...]

2 Date of Manufacture: ___________________________ Fecha de fabricación:, Date de fabrication: Serial No: ______________________________________ Número de serie:, Nombre d'ordre GB ENGLISH EC-DECLARATION OF CONFORMITY We declare under our sole responsibility that this product is in conformity with the regulations EN292- 2: section 3 of 1992 [...]

3 indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. used without the safety al[...]

4 Fig. 6 Fig. 5 Fig. 2 Fig. 3 Fig. 4 1. Read and understand tool labels and manual. Failure to follow warnings could result in DEATH or SERIOUS INJURY . Fig. 1. 2 . Operator and others in work area MUST wear safety glasses with side shields. These safety glasses must conform to ANSI Z87.1 requirements (approved glasses have “Z87” printed or sta[...]

5 9. Do not connect tool to pressure which potentially exceeds 200 PSI (13.7 BAR). 1 0 . All air line components (hoses, connectors, filters, regulators, etc.) must be rated for a maximum working pressure of at least 300 PSI (20.7 BAR) or 150% of the maximum system pressure, which ever is greater. 11. Connect tool to air supply hose with a coupling[...]

6 21. Do not load fasteners with trigger or safety depressed, to prevent unintentional firing of a fastener. Fig. 13 22. Remove finger from trigger when not driving fasteners. Never carry tool with finger on trigger. Contact Actuation tools will fire a fastener if the safety mechanism is bumped while trigger is depressed. Fig. 14. 23. Do not overre[...]

7 Employer must enforce compliance with the safety warnings and all other instructions contained in this manual. Keep this manual available for use by all people assigned to use this tool. For personal safety and proper operation of this tool, read and understand tool labels and manual. Failure to follow warnings could result in DEATH or SERIOUS IN[...]

8 4. Feed the strip of fasteners into the magazine (“T” slot), until they are past the spring (A) Fig. 21. 5. Pull the follower (B) Fig. 22 all the way to the rear of the magazine and release. The follower will apply pressure to the strip of nails to feed it into the driving mechanism as shown in (B) Fig. 22A . 6. Adjust directional exhaust def[...]

9 OPERA TING INSTRUCTIONS USING THE TOOL WITH SELECT ABLE TRIGGERING OPTIONS Complete all steps of PREPARING THE TOOL before using the tool. This tool is shipped from the factory with a selectable trigger set in the “SINGLE SEQUENTIAL ACTUATION” firing mode as described in number 1 below. This actuation design requires the release of both the t[...]

10 IMPORTANT: A trigger, whi ch will limit the tool to “ single sequential actuation ” only, is available free-of-charge by calling 1-800-321-9443 in the United States and Canada or 001-731-660-9374 outside the United States and Canada, and providing t ool model number, type, serial number, etc. For identification purposes: the single sequentia[...]

11 CLEARING A JAMMED F ASTENER Disconnect tool from air supply. 1. Remove any remaining fasteners from the nailer. A. Place finger in recess (A) Fig. 28, and depress lever to release follower mechanism. B. With follower release lever depressed (A) Fig. 28, slide follower all the way to the front of the magazine. C. Depress spring (B) Fig. 29, slide[...]

12 CLEAN AND INSPECT DAIL Y Disconnect tool from air supply before cleaning and inspection. Correct all problems before placing the tool back in use. Wipe tool clean and inspect for wear or damage. Use non-flammable cleaning solutions to wipe exterior of tool only if necessary. DO NOT SOAK tool with cleaning solutions. Such solutions can damage int[...]

13 SERVICE AND REP AIRS All quality tools will eventually require servicing or replacement of parts due to wear from normal use. For assistance with your tool, visit our website at www.porter-cable.com for a list of service centers or call the Customer Care Department at 1-800-487-8665. All repairs made by our service centers are fully guaranteed a[...]

14 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its nailing and stapling tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material [...]

The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II™, Delta ® , DELTACRAFT ® , D[...]