Philips 32HFL5007D/10 инструкция обслуживания

Philips Hospit ality TV Installation manual for 32HFL5007D/10 42HFL5007D/10 47HFL5007D/10 55HFL5007D/10 Version 1.1[...]

1 Contents 1. Requirements befor e starting the installation .......................................................................................................... 2 2. Find out the state of the TV ...................................................................................................................................... 3 3. Re -inst[...]

2 1. Requirements bef ore starting the installation Before starting the in stallation, make sure that you have everything you need at hand. Master remote control 22AV8573 or Guest remote control 22AV1109A And USB stick You will need the master remote c ontrol or the gu est remote c ontrol to access th e menus. To access the setup menu press the ‘[...]

3 2. Find out the state of the TV It is important t o know if a TV is in ‘virgin mode’ (out o f the box) or ins talled befor e. If you can see this screen below , you know that the TV is in ‘virgin mode’ an d you can install the set. See cha pter 4 of this manual . If you power on the set and then press the ‘Home’ button on the guest re[...]

4 3. Re -install TV If you want to start an installation from scratch you can always re-install the TV. This can be done by using the option: Re-install TV set. If PBS is active you c an access the setup menu press the ‘RC5 SETUP’ key, and t hen press the ‘Home/Menu’ button (For the guest remote control, press the following keys in sequence[...]

5 Pr ess “OK ” to access the sub -menu , n avigate to “Rein stall TV” . Press “OK” to r einstall the TV set. If all is correct select “YES” and press “OK ”. After this operation the TV will p ower off and on and display the installation wizar d. Note: All settings are at default values and no channel plan is available. After rei[...]

6 4. Installation wizard When you turn on th e TV for the first ti me, or you hav e reinstalled the TV, you sh ould see the foll owing screen. Here you will need to select your pr eferred language . After this, you will need to select the country. Depend ing on the countr y selection, some pre-defined s ettings will be activated, because of local b[...]

7 The next step is to select ‘Wall mount ed’ or ‘On a TV stand’. This option changes some settings for the audio and image of the TV. Now you can select the visual an d hearing impair ed options. If you select ‘ O n’ , your TV will automaticall y turn on settings to help visual and h earing impaired people. THE MOST COMM ON OPTION IS TO[...]

8 For the channel installa tions, select ‘In stall TV channel s’ and press ‘OK’ Then you can selec t ‘Continue’ and press ‘ OK’ again. Here you can sel ect the type of channels you would lik e to install and what prefer ence you will use. It is advisable to ch eck the settings befor e starting the search.[...]

9 Note : If all options are disabled you have to go down to the Digital channels option and set the digital channels to ON. A screen is display ed to make chan ges to set the channel list/ map configurati on: [Symbol rate mode]: Au tomatic TV will use the p reset Symbol rate (6.900/6. 875) Manual Option to s et Symbol rate 1 and Symbol rate 2 [Symb[...]

10 Frequency step size has two options : 1. “ 1 MHz ” – With Full scan, the step size to search for channels is 1 MHz. The scan will take more time but will find also channels br oadcasted n ot according to th e channel grid. 2. “ 8 MHz (default) ” – With Full scan, the step size to search for channels is 8 MHz. The scan will be shorter[...]

11 During the channel search you can see the progre ss bar and how many channels are found at that time. When the search is done, you should see “ Channel search complete ” and a summary of the channels found. In this case: Digital channels found : 53 Analogue channels f ound: 0 Press the “ OK ” bu tton on the re mote control to finish the [...]

12 The wizard will ask you some que stions about which image you prefer, select th e option you d esire and press “ OK ” on the remo te control. Once this wizard is d one, you will r eturn to the installation menu again. The ne twork wizard will guide you throug h network setup. This wizard will popup :[...]

13 Please select “Ne xt” and press O K to continue The connection will be made to wir eless network or via wired n etwork, depend ing on prefer ences. TV will automatically acquire an IP address if this is a vailable via DHCP. After the connecti on is made, the result is shown on th e TV. The last option in this menu is “ Add your devices ”[...]

14 When you are don e with this, sele ct “ Done ” and pr ess ‘OK’ on the re mote control . After pressing “ Done ” you have completed the installation of the TV and you should see this screen. Press “OK” on the remote control to exit this wizard . Note: This wizard will not be available anymore when you start the TV the next time. T[...]

15 5. Channel options a. Reordering channel s For reorderin g TV channels the channel plan from PBS Setup must be used. In consumer menu you cannot rearrange channels. The PBS Setup can be access ed by using the Yellow remot e (RC 22AV8573 Mast er Remote control) and pressing the MENU Button or with the TV remote pres s 3,1,9,7,5,3, MUTE). The PBS [...]

16 Navigate to the channel that y ou want to m ove and press “OK” on the re mote control to select that channel. The arrows around the channel indicate that the channel is selected and can be moved. Use the arrow keys to move the channel to the ne w position. When you reached th e new position pr ess “OK” on the remo te control to confirm t[...]

17 Press “OK” on the r emote control to confirm that you are done with the r e-ordering. b. Rename channels Select the channel, press the “Options” button on the rem ote contr ol and select “ Rename ” to change name of a channel. If you then pr ess the “OK” button a virtual Q WERTY keyboard will p op up. c. Hide channels Important: [...]

18 6. Professional Setu p [Professional Se ttings] Select the Setup menu language to be English, French, German or Italian. [Professional Mo de] [Off]: The TV operat es as a basic (c onsumer) TV. [On]: All setting s in the P BS mode Setup menu are active. Only by switching on thi s mode the TV will act as a Hospital ity TV. [NetTV] [Configure Net T[...]

19 [Icon Label] Change the label of the [Browse Por tal] icon. [Portal URL] Enter the URL to access from [Browse Portal] . The address is for the SmartUI external s erver. [Room ID] Entry field to store 4 digits to set the Room Identifier. Room ID ca n be used to distinguish between different floors/rooms/setup s when using SmartInstall. [Switch on[...]

20 [Switch on featu re] Starts up in Theme TV, Smart UI or Net TV modes. [Blank Until Fe ature] The TV will remain bla ck until the F eature is fully l oaded. Note: Enabling this option will in crease the startup ti me. [Switch on Pictu re Format] Switches to a pre-defin ed picture f ormat. [Display messa ge] [On] To enable the w elcome message. [O[...]

21 [Local keyboa rd lock] [Off]: The local keyboar d (co ntrol buttons on TV) buttons are enabled. [On]: The local keyboard (control buttons on TV) buttons are disabled, power butt on still enabled. [All]: All local keyb oard (control buttons on TV) butto ns are disabled. [Remote control lock] [OFF]: All buttons on the guest re mote control will fu[...]

22 [Browse USB] Enables / disables the USB Browse icon to be presented in the Guest Menu. [Off]: When set to Off, the TV will hide the USB icon in the Home menu. [On]: When set to On, the TV will show the USB icon in the H ome menu. [Auto scart] Enables auto scart s witching (or break-in) in Professi onal mode. [AV]: Enables auto scart switching or[...]

23 [SXP Baudra te] Sets the Baud rate f or the Serial Express communication cha nnel to be 382 00 or 19200 Baud (bits per sec ond). [Enable CI-slot] Enables or disables the use of the integra ted CI/CI+ slot: [Off]: No pass through of the TV input signal via the CI-Slot Card is possible; the use of CI Card slot is not p ossible. [On]: Pass through [...]

24 [Enable subtitle] Enables or disables the use of subti tles in a DVB broad cast channel : [Off]: No subtitles s ervices available [On]: Subtitles servic es avail able [Enable Chann el Map] Select Channel Map to be viewed : [Native]: Show stand ard default channel map [BDS]: To be used only if a system is connected [Source setup] Lists all suppor[...]

25 [Scrambled Prog ram OSD] Show OSD on scra mbled TV chann el. [Power settings ] The possible p ower settings are explai ned below. The power on function allows the TV to enter a specific mo de ([On], [Standby], or [Last stat us]) of operation when the mains power is activated (cold s tart): [On]: The TV will always turn on (show startup channel) [...]

26 [Delayed reboot] Enables or disables the use of del ayed standby: [On]: TV is able t o switch on im mediately after switching to stand by. [Off]: Switch ON time of the TV will be longer after switc hing to stand-by. [Standby Delay Timeout] This option will se t the amount of ti me for Delayed reboot. 5 mts – TV will p ower down co mplete after[...]

27 [Time Downloa d] Select the sourc e for the clock ti me: [Automatic]: Clock time is retrieved from the “Download Program ” channel. [Manual]: The cl ock time is set using the Time Set ting option. Note: If the power is disconnected the TV will lose the time set. [Download Coun try] Set the selected country as the source for clock tim e. [Dow[...]

28 [Reference Time an d Date] [Feature settings ] Check Feature setting s (page 3 3) [Speaker setting s] [TV Speaker Ena ble] [Off]: The main speakers are muted. The RC can control the volume and mute the headp hone/bathroom speaker [On]: The main speakers are active and the behavior of the headphone/bathro om speaker is defined by the Independent [...]

29 [Headpho ne] The default volum e for headph ones can be set. The value define will be applied when the headphones are connected. [Factory defau lt] Restore the factory d efault of the PBS Menu. Channel installati on is not affected. [TV Setup] A shortcut to en ter the consumer ins tallation menu. Consumer installati on me nu should b e accessed [...]

30 [Smart Clone] Check Smart Clone section (pag e 32) [RF Download ] Check RF Downl oad section (page 3 4) [Express Box] Only applicable for system connected installation. After storing PBS settings, t he TV will restart to apply the new par ameters. No w you can clone all se ttings to other TV sets by using the option TV to USB and USB to TV. Che [...]

31 7. Welcome Logo There are 2 Philips l ogos displ ayed at startup. The s econd logo can b e replaced b y a picture upload ed via US B. File format: 12 80 x 720.jpg fi le. The Welcome L ogo is disp layed only when Standb y mode is s et to “Green”. Note: below timing values are approximate indications and can differ from the real situation! Wel[...]

32 8. Smart Clone Smart Clone With Smart Clone i t is possible to c opy to/from a USB device TV the configuratio n data and channel lis t data. Place a USB Memory stic k in the USB side connector of the TV. *The USB device sh ould be formatt ed as FAT or FAT3 2. [USB to TV] 1. Select [Smart Cl one] and press OK. 2. Select [USB to TV] and press OK. [...]

33 9. Feature settings [Multi RC] This function allows tha t up to four tele visions can be installed in a ro om whereas every TV will listen t o its own RC. Once the TV is se t, also eve ry RC can be set to remember its c onnected TV: [Off] Multi RC is turn ed off; all TVs will listen to a ‘blue’ RC. The TV will listen t o a ‘blue’ RC. Pr [...]

34 10. RF Download Instead of using a USB memory de vice to d o cloning and firmware up date, this up grading is also possib le using the RF infrastructure. This is sup ported by S martInstall (Phili ps Hospitality RF Download mechanism) and allo ws a simultaneous upgrad e of all installed t elevisions. [Start Downloa d]: To manual ly start a RF d [...]

35 11. CSM (Consumer Se tup menu) The CSM contains data about the TV s oftware, serial n umber and other details. The m enu can be acce ssed using a standard remote c ontrol or usin g the master re mote control. 1. Using the standard remote contr ol: press the f ollowing key sequence “1,2,3, 6,5,4” 2. Using master re mote con trol (22AV8753D) :[...]