Pelco C3427M-D (2/09) инструкция обслуживания

INST ALLA TION C3427M-D (2/09) IS150 Series Camclosure ® Integrated Camera System[...]

[...]

C3427M-D (2/09) 3 Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 [...]

4 C3427M-D (2/09) List of Illustrations 1 Package Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2 Ceiling/W all Installati on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 Ceiling T i[...]

C3427M-D (2/09) 5 Regulatory Notices This device complies with Part 15 of the FCC Rules. O peration is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE Th[...]

6 C3427M-D (2/09) Description The IS150 Series Camclosure ® integrated camera system combines an environmental cover , back box, camera, lens, and lower dome into a small, high-securi ty system that is quick and easy to install. The system is perfect for a variety of indoor and outdoor applications and its versatile design allows for multiple moun[...]

C3427M-D (2/09) 7 Indoor/outdoor dome, vandal resistant, in-cei ling mount, clear bubble, liner , gray finish PARTS LIST T able B. IS151, Clear Bubble with Liner Camera T ype Lens/Iris NTSC P AL Color , Wide Dynamic Range, Day/Night 3.0 to 9.5 mm, Day/Night V arifocal, Auto Iris IS151-DWV9 — 9.0 to 22 mm, Day/Night Varifocal, Auto Iris IS151-DWV2[...]

8 C3427M-D (2/09) Figure 1. Package Components BA C K BOX 1 EA. < OR > 1/8-IN C H HOLLOW SC REWDRIVER BIT 1 EA. ADAPTER PLA TE 1 EA. S HOWN A C TUAL S IZE S HIPPING BOX 8-32 X 1.25-IN C H PHILLIP S FLA T HEAD SC REW S 4 EA. 8-32 X 0.75-IN C H PHILLIP S FLA T HEAD SC REW S 2 EA. 8-32 X 0.375-IN C H PHILLIP S FLA T HEAD SC REW S 4 EA. TRIM RING[...]

C3427M-D (2/09) 9 Cover and Back Box Installation The IS150 Series Camclosure integrated camera system mounts only into a wall or ceiling. UNSHIELDED T WISTED PAIR (UTP) VIDEO The IS150 Series offers support fo r unshielded twiste d pair (UTP). The UTP video output signal is 1 Vp-p differential into a 100-ohm load. At a minimum, UTP requires Cat5, [...]

10 C3427M-D (2/09) SUSPENDED CEILING NOTE: Y o u should install the camera module into the back box before installing the back box into the surface. When installing the back box into the surface, rotate the camera modu le to access the mounting holes (refer to Came ra Module on page 12 for more informatio n). 1. Pull the video and p ower wires to t[...]

C3427M-D (2/09) 11 4S DEEP ELECTRICAL BOX NOTE: Y o u should install the camera module into the back box before installing the back box into the surface. When installing the back box into the surface, rotate the camera modu le to access the mounting holes (refer to Came ra Module on page 12 for more informatio n). 1. Attach the supplied adapter pla[...]

12 C3427M-D (2/09) Camera Module The IS150 Series Camclosure camera modu le includes the camera, came ra bracket, and heate r board. T o perform most camera adjustments, you must remove the module from the back box. Use the following instructions to re move and reinstall the camera module. MODULE REMOVAL T o remove the camera module from the back b[...]

C3427M-D (2/09) 13 2. Unplug the camera (10-pin), service (3-pin), and heater board (4-pin) connectors from the back box (refer to Figure 6). Figure 6. Back Box Connectors C AMERA C ONNE C TOR HEA TER BOARD C ONNE C TOR S ERVI C E C ONNE C TOR[...]

14 C3427M-D (2/09) CAMERA ORIENTATION At the factory , the camera module is configured for ceiling mounting. For wall mou nting, you must change the camera orientation or the video image could be upside down or sideways. T o change the camera orientation (refer to Figure 7): 1. Remove the camera module from the back box, if necessary . 2. Remove th[...]

C3427M-D (2/09) 15 Camera Adjustments T o perform the following camera adjustments, make su re to connect the camera and service connectors. Y ou may have to remove the camera module from th e back box. Connect a monitor . Then turn on power to th e camera and monitor . T o use the service connector , r efer to Service Connector on page 27. T o set[...]

16 C3427M-D (2/09) T o adjust the fo cus: 1. Loosen the focus locking screw . 2. Position the inverted dome approximately 0.125 inch (3.175 mm) from the front of the lens. Make sure that the lens and the dome are cen tered (refer to Figure 9). 3. T urn the focus locking screw clockwise or counterclockwise to adjust the focus. 4. When the optimal fo[...]

C3427M-D (2/09) 17 DN/CH SERIES ADJUSTMENTS Refer to Figure 10 to adjust the IS150-DN or IS150-CH model. Figure 10. Adjusting the IS150-DN/C H Series Camclosure SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation. SW4-1: Auto Gain Control The automatic gain control (AGC) adju sts the image au tomatically to compensate[...]

18 C3427M-D (2/09) SW4-4: Flickerless In certain lighting conditions, a flicker in the light source may affect camera operation. Flic kering can be caused by a number of conditions, including the qua lity of the source power and the age and type of fluorescent bulbs and ballasts. Set SW4-4 to ON to enable flickerless operation. The ca mera will rem[...]

C3427M-D (2/09) 19 V ERTICAL PHASE ADJUSTMENT Use this procedure for 24 V AC ope ration only . When using more than one camera power supply, a brief vertical roll may occur on the monitor when switching from one came ra to another . T o eliminate vert ical roll, reverse the 24 VAC connec tions on one camera. If both cameras are connected to the sam[...]

20 C3427M-D (2/09) DAY/NIGHT OPERATION NOTE: This section only applies to DN model cameras. DN model cameras regularly check the brightness level of the field of view t o determine when to switch between day (color) and nig ht (black-white) operation. Actual brightness threshold levels are affected by camera angle, amount of zoom, field of view , l[...]

C3427M-D (2/09) 21 DW/CW SERIES (WIDE DYNAMIC RANGE) ADJUSTMENTS Refer to Figure 12 to adjust the IS150-DW or IS150-CW model. Figure 12. Adjusting the IS150-DW/C W Series Camclosure SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation. SW1-1: Video Format Set SW1-1 to ON for NTSC. Set it to OFF for P AL. The default se[...]

22 C3427M-D (2/09) SW1-4: Auto White Balance/Ma nual White Balance Auto white balance (AWB) is enabled by default (ON). T o manually set and lock the white balance: 1. Set SW1-4 to ON. 2. Hold a white background in front of the lens until the video shows all white. 3. While holding the background in place, set SW1-4 to OFF . A green block and a whi[...]

C3427M-D (2/09) 23 SW1-8: Day/Night Operation (DW models only) NOTE: On CW models, SW1-8 is unused and does not affect camera operation. DW model cameras regularly check the brightness level of the field of view to determine when to switch between day (color) and nig ht (black-white) operation. Use SW1-8 to set the general light levels at which the[...]

24 C3427M-D (2/09) AUTO IRIS LEVEL ADJUSTMENT The electronics of the IS150-DW and IS150-CW Series Camclosures automatically adjust the camera to the auto iris. Auto iris level adjustments are n ot necessary . V ERTICAL PHASE ADJUSTMENT Use this procedure for 24 V AC ope ration only . When using more than one camera power supply, a brief vertical ro[...]

C3427M-D (2/09) 25 Camera Positioning Rotate and tilt the camera module to position the camera. Then tighten the tilt screws (axis ì in Figure 14). NOTE: Do not over -rotate the module. Excessively turni ng the module in one direction could result in damage to the wiring. Figure 14. Positioning the Camera ì T ilt 80° (20° to 100°) î Pan 360°[...]

26 C3427M-D (2/09) Install Liner and T rim Ring 1. Adjust the liner (if installed), refer to Figure 15: a. Align the screw holes in the trim ring with those in the back box to identify the proper liner position. b. Loosen the three Phillips screws located in t he trim ring. c. Insert the blade of a standard screwdriver in one of the adjustment groo[...]

C3427M-D (2/09) 27 Service Connector The IS150 Series Camclosure integrated camera system includes a service connector that outputs camera video. Use it at the installation site to se t up the field of view and to focus the camera. Figure 16. Service Connector Pelco offers two optional items that plug directly in to the service connector . Before u[...]

28 C3427M-D (2/09) T o assemble the cable: 1. Attach the CPM 88 miniature coaxial connector to one end of the cable. Follo w the directions supplied with the mini ature coaxial connector . 2. Attach the 2.5 mm monaural plug to the other end of the coaxial cable (refer to Figure 17): a. Remove the support sleeve from the plug. b. Slip the support sl[...]

C3427M-D (2/09) 29 Specifications GENERAL Pan/T ilt Adjustment Manual Pan 360° T ilt 80° (20° to 100° range) Rotation 360° Construction Aluminum with steel camera mounting bracket and polycarbonate dome Finish White polyester powder coat trim ri ng with gray polyester powder coat back box Light Attenuation Smoked f/1.5 light loss Clear Zero li[...]

30 C3427M-D (2/09) CAMERA/LENS If you need technical specifications for the camera itself, refer to the IS150 specification online at www .pelco.com . (Design and product specifications subject to change without notice.) 2.42 (6.15) 1.75 (4.45) 3.50 (8.89) 5.48 (13.92) NOTE: VALUE S IN PARENTHE S E S ARE C ENTIMETER S ; ALL OTHER S ARE IN C HE S . [...]

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merc handise pr oved defective in mate rial or work manship for a period of one year after the date of shipment. Exception s to this warrant y are as noted bel ow: • Five years: – Fiber optic products – TW3000 Series un shielded twiste d pair (U[...]

Pelco, Inc. W orldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el (800) 289-9100 Fax (800) 289-9150 International T el +1 (559) 292-1981 Fax +1 (559) 348-1120 www .pelco.co m[...]