ParaBody PBF501 инструкция обслуживания

PARABODY INC. EXS00 BASE UNIT PBFS01 :: - PRODUCT ASSEMBLY INSTRUCTION SHEETS TOOLS REQUIRED" FOR ASSEMBLY: 9/16 INC~ SOCKET 3/4 INCIt SOCKET ADJUSTABLE WRENCH B.AMMER or RUBBER MALLET 3/16 ALLEN WRENCH 5]32 ALLEN WRENCH REVISION: ..W ¯ If you experience any problems with the assembly of this product, please contact your dealer or your PARABO[...]

PBFS01 EXS00 BASE ~IT ASSEMBLY INSTRUCTIONS (STEP #I) TIIE INSTRUCTIONS FOR STEP #I ARE TO BE USED WITH DRAWING SHEET #I OF 6. THE PARABODY EXS00 BASE UNIT M’L!ST BE ASSEMBLED ON A FLAT LEVF, L SURFACE TO ASSURE ITS PROPER FUNCTION. PARABODY INC. STRONGLY RECOMMENDS THAT TI-IIS PRODUCT BE ASSEMBLED BY TWO PERSONS TO AVOID POSSIBLE INJURY *** IMPO[...]

PBFS0t EXS00 BASE UNIT ASSEMBLY INSTRUCTIONS (S~fEP #3) THE INSTRUCTIONS FOR STEP #,’3 ARE TO BE USED WITH DRAWING SHLET #4 OF 6. Place each of the two (2) WEIGHT STACK BUMPERS over the GUIDE ROD HOLES (RADIUS EDGES FACING UP) on the WEIGHT STACK SUPPORT BASE. Insert each of the two (2) GUIDE RODS through the WEIGHT STACK BUMPERS and into the WEI[...]

PBFb01 EXb00 BASE UNIT ASSEMBLY INSTRUCTIONS #!) Insert one (1) 2 IN. SQ. END CAP into the BASE SEAT SUPPORT and carefully place it on its side the floor. o , ~,8X 1- Loosely assemble the BASE SEAT SUPPORT to the MAIN BACK SUPPORT, using two (2) "~ 1/4 BOLTS, four (4) 378 WASHERS, two (2) 3/8 LOCK WASHERS, and two (2) 3/8 Insert a 2 IN. SQ. EN[...]

PBFS01 EXS00 ASSEIVI.BLY PARTS LIST FOR STEP COUNT ALL PARTS BEFORE BEGINNING ASSEIVIBLY HARDWARE:. ITEM NAME/DESCRIPTION 2. 3. 4. 5. 6. 7. 9. 10. 11. 12. 13. 14, 15. 16. 17.. 18. QTY BAG # v A (PURPLE) i/2 X 3-1/2 LG. BOLT ............................................................................................................. I/2 X 3 LG. BOLT[...]

PBFS01 E-X~0 ASSEMBLY PARTS LIST FOR STEP #2 COUNT ALL PARTS BEFOILE BEGINNI~ G ASSEMBI,¥ WELDMENTSfPARTS ~ ITEM NAME/DESCRIPTION QTY 2. 3. 4. 5. 6. 7. 8. 9. ADJUSTABLE PRE STRETCH SLIDE ...................... (PB1818-1) ....................................... 1 LEG CURL EXTENSION ’ (PB2296-1) ....................................... 1 ADJUSTABLE[...]

i0. 12. 13. 14. 15. 16. 17. ]9. 20. EXS00 BASE UNIT ASSEMBLY INSTRUCTIONS (~TEP #2) Insert two (2) 2 IN. SQ. END CAP into the TOP and BOTTOM ends of the LEG CUI~ EXTENSION. Securely assemble the LEG CURL EXTENSION onto the BASE SEAT SUPPORT, using one (1) I/2 .3 BOLT, and one (I) I/2 LOW HEIGHT LOC]:,I NUT. Attach one (1) RUBBER BUMPER to thefront [...]

PBFS01 EXS00 BASE UNIT ASSEMBLY INSTRUCTIONS (STIgP #2) THE INSTRUCTIONS FOP, STEP #2 ARE TO BE USED WITH DRAWING SHEET #2 & #3 OF 6. Securely assemble ~wo (2) 3/8 DIA. x 2 IN. BUSHING PULLEYS into the TOP BOO[V/SECTION and tl~ee (3) 318 DIA. x 2 Ii~. BUSHING PULLEYS ~nto the MAIN BACK SUPPORT, using five (5) 3/8 6-1/2 BOLTS, ten (10) 3/8 WASHE[...]

PBFS01 EXS00 BASE U-NIT ASSEMBLY INSTRUCTIONS (~,TEP #2) 24. Attach eight (8) PARAGLIDE STRIPS to the ADJUSTABLE SEAT FRAME and the :BASE SEAT SUPPORT as shown in DETAIL A and B on the reverse side of the main assembly drawing for STEP #2, (SHEET #3 of 6), using the following steps: A. Thoroughly clean all inside and outside surfaces where the para[...]

¯ y PBFS0i EXS00 ASSEIViBL ’ PARTS LIST FOR STEP COUNT ALL PARTS BEFORE. BEGIIN-NING ASSEMBL HA~A~:. ITE~ N~E~ESC~PTION ~.~G ~ ~ (Om~G~) I. ~IGHT STACK BUMPE~ ................................................................................................... 2.. 3/8 ~. DIA. GUIDE ~OD ~S~ATO~ ......................................................[...]

PBFS01 EXS00 ASSEiVEBLY PARTS LIST FOR STEP #4 COUNT ALL PARTS BEFORE BEGINNING ASSEIVEBLY I-IAR_D ~rARE,:. ITEM NAME/DESCRIPTION QTY 2. 3. 4. 8. 9. 10. 11. BAG # ~. (BRO~.~) 5/16 X I BOLT ........................................................................................................................ 1 3/8 X I-3/4 BOLT .....................[...]

PBFS01 EXS00 BASE UNIT ASSEMBLY INSTRUCTIONS iL~i~r ~.) TIIE INSTRUCTIONS FOP, STEP #4 A_~.E TO BE USED WITH DI%4.W~NG SI-~:ETS #S & #6 OF 6. Assemble the SWIVEL PULLEY BRACKETS using (1) 3/8 Dia x 3/4 BOLT, (2) :511 5 WASHER, 3/8 WASHER and (1) 3/8 LOCKNUT (TIGHTEN TILL LOCKED THEN BACK[ NUT OFF 1/4 TURN). Loosely assemble two (2) 3/8 DIA. x 1[...]

PBFS0! EXS00 BASE UNIT ASSEIVIBLY INSTRUCTIONS (STEP #4) ![! WARNING MAKE SURE SN.A-P HOOKS ARE FASTENED BEFORE DOING ET~]~&CISES. !t! WARNING !!! DO NOT OPERATE TId[IS IVIACHINE WITII LAT BA~. OFF SAFETY HOOKS EXCEPT DURING I-IIGI:! PULLEY EXERCISES. ALSO, LAT BAI’,. _IS NOT TO BE USED FOR PULL-UPS. ~ !!! ATTENTION USER INSTRUCTION !!! BEFOR[...]

oo[...]

.! DETA I L ~A" UNIT STEP ~ 1 SHEET ~ OF (~[...]

INSII3E £/]NNECTION Z. 5 .~ . E..N~ ~JIVEL PULLEY[...]

EXS’OD BASE UNIT ._STEP SH EET ?_ OF E,[...]

31’.4 REVISIONS ¢_HAF’F LE.~, CURL EXTEN ¢,I~3N ROLLER PAD SLEEVE bETA/L "N" % "~ I ParaBody~ inc. RAMSEY, MINNESOTA 1~.,,,,,,’-,*" t’ ~ Ass"r, STEP ~’ _ I..,,_,-~_.,~, I DI PtSF501[...]

UNIT STEP #?_ CONT’D _SHEET S OF G,[...]

~’. .’.[...]

"bETA I L’E" ¯ .. ~ ..::’.’ .....,..:,,.....~;. ¯ . :: : . .’..~ ....,... ~. WFJ~iT ,’PLATE, ¯ C Z PER.. PLA’TE’~ . ~TA C1¢. L DETAIL "F" :’~ "~EE DE[...]

I[...]

[...]

PULLEY i ~.AI~LE ROUTIN~ I?IAbRA/4[...]

o¢ DETAIL[...]