Orient Technologies BTP-R880NP инструкция обслуживания

U USER’S MANUAL Receipt Printer BTP-R880NP Shandong New Beiyang Information T echnology Co., Lt d[...]

BTP-R880NP User’s Manual 1 Declaration Information in this document is subject to change without notice. SHANDONG NEW BEIY ANG INFORMA TION TECHNOLOGY CO., L TD. (hereinafter re ferred to as “SNBC”) reserves the ri ght to improve products as new technology , compone nts, so ftware, and firmware become available. If users need further data abo[...]

BTP-R880NP User’s Manual 2 General Safety Information Before installing and using the printer, please read the following items carefully. 1. Safety instructions Don’t touch the tear bar of printer. The print head is a thermal element and it is at high temperature du ring printing or just after operation, therefore please do not touch it and its[...]

BTP-R880NP User’s Manual 3 Content s TU 1 ． INTRODUCTION UT ............................................................................................................................... ........... 1 TU 1.1 O UTLINE UT .............................................................................................................................[...]

BTP-R880NP User’s Manual 4 TU 6.4 E THERNET INTERF ACE UT ............................................................................................................................... 16 TU 6.5 WLAN INTERF ACE UT ............................................................................................................................... .....[...]

BTP-R880NP User’s Manual - 1 - 1 ． Introduction 1.1 Outline BTP-R880NP is a high performance thermal printer, which can be widely used for real-time printing application, such as POS system , restaurant syste m, ATM, etc. BTP-R880NP can be connected with ot her devices via parallel interfac e, serial interface, USB, Ethernet or WIFI and is avai[...]

BTP-R880NP User’s Manual - 2 - 2 ． S pecifications 2.1 Main specification Item Specification Color Black or Ivory Print Method Direct Thermal Resolution 203 × 180 DPI(standard) Paper width 57.5/ 69.5/76/80/82.5mm Print width Max. 80mm Standard: Max 230mm/s Gray scale print speed:Max.150mm/s Print speed Bi-colour print speed: Max. 120mm/s Flash[...]

BTP-R880NP User’s Manual - 3 - Button FEED button LED POWER LED, ERROR LED Machine Interface Buzzer Built-inInternal Buzzer, the volume can be adjusted. Lifetime of print head 150 km(standard test condition) Lifetime of cutter 1,800,000 cu ts(standard test condition) MCBF 60,000,000 lines Reliability MTBF 360,000 hours Operation condition 5°C to[...]

BTP-R880NP User’s Manual - 4 - z Paper type: Continuous thermal paper z Paper supply method: Paper roll z Paper width: 82.5±0.5mm,80±0.5 mm, 76±0.5 mm,69.5±0.5mm 57±0.5mm z Paper thickness: 0.06mm-0.1mm z Thermal senstive layer: Outside z Paper roll specifications OD(MAX): ф 83mm z Recommended reference paper: Paper type Manufacturer TF50KS[...]

BTP-R880NP User’s Manual - 5 - Caution: The printer will measure the marks during the printing or feeding process. If the l engths of the mark (L1) is larger than the default value (default: 13 mm), the printer will give a paper-end alarm. 2.4 Print and tear off position 2.4.1 Print position z L1: Paper holder width: 83.5±0.5mm z L2:Max Print wi[...]

BTP-R880NP User’s Manual - 6 - 3 Outline and component s 3.1 Outline and Parts 1—Power LED 2—Error LED 3—Feed button 4—Tear bar 5—T op cover latch 6—Cutter cover 7—Middle cover 8—Power switch 9—T op cover 10—LOGO plate 1 1—T op cover 12—T op-cover-open sensor 13—Paper sensor 14—Paper guide 15—Paper near-end sensor 16[...]

BTP-R880NP User’s Manual - 7 - d- Power switch (8) “O” power is to turn off printer . “—” power is to turn on printer . e- T op cover uplifting alarm sensor Monitor top cover status: open/close. f- Paper end sensor T o detect if p aper is existing or not wh en using continuous paper; T o detect the paper mark when using black mark p ape[...]

BTP-R880NP User’s Manual - 8 - 4 Inst allation 4.1 Unpacking Check whether all items, which are listed on the pa cking list, are present and in a good condition. If any item is damaged or missing, please contact y our dealer . 4.2 Printer installation The BTP-R880NP can be installed in two positions: hor izontally on a t able or vertically on a w[...]

BTP-R880NP User’s Manual - 9 - 4.3 Connecting the Power Adapter 1) Confirm the power switch is turned off. 2) Insert the power cord into the pow er socket on the back of the printer. Caution:  Use only the manufacture rs supplied power adapter or other equal model.  When connecting or disconnecting the cable connector of the po wer adapter,[...]

BTP-R880NP User’s Manual - 10 - 1) Turn off the printer. 2) Open the printer top cover, as in the following figure. 3) Drop in a paper roll in the paper house. 4) Pull the paper roll into the paper holder , and close the printer top cover . 5) T ear of f the surplus portion of the paper by using the tear bar . Caution: User can adjust the paper g[...]

BTP-R880NP User’s Manual - 1 1 - Paper guide in the slot 3&4: 57 ±0.5mm  Confirm that the paper is rolled ti ghtly on the paper roll, otherwise, paper jam or other fault may occur.  The paper roll should be placed stra ight in the paper compartment and not at an angle. The paper roll should be able to move freely. 4.8 Paper near end ad[...]

BTP-R880NP User’s Manual - 12 - 4.8.2 Remaining p aper amount adjustment of Paper near end sensor Remaining paper amount can be adjusted by adjus ti ng the position of paper near end sensor Paper near end sensor has six levels, the red mark (actual color on printer is white) shows the current leve l and it can be adjusted to a different position [...]

BTP-R880NP User’s Manual - 13 - 5 Printer maintenance Caution:  Before starting routine maintenance, confir m that the printer power is turned off.  Do not use solvents like gasoline or acetone.  When cleaning sensors, the prin ter should not be switched on until the pure alcohol has totally evaporated.  It is recommended that the mai[...]

BTP-R880NP User’s Manual - 14 - Caution:  The cutter sliding blade act s slowly during revo lving the thumb wheel. Go on revolving and observe carefully;  If the thumb wheel cannot be turned, do not force the wheel, instead turn it the opposite direction.[...]

BTP-R880NP User’s Manual - 15 - 6 Interface Signal 6.1Parallel interface Parallel interface can work in IEEE 1284 comp atible mode or half-byte mode. The interface is 36PIN CENTRONICS. The Interface is defined as below: PIN Source Functio n 1 H nStrobe 2 H Data 0 (Least Significant Bit) 3 H Data 1 4 H Data 2 5 H Data 3 6 H Data 4 7 H Data 5 8 H D[...]

BTP-R880NP User’s Manual - 16 - 6.2 RS-232 serial interface The serial interface of the printer is comp atible with RS-232, its connector is 25PIN female D type. PIN No. Signal de finition PIN1 Frame Ground PIN2 TXD PIN 3 RXD PIN 4 RTS PIN 5 Not connected PIN6 DSR PIN 7 Sign al Ground PIN 8~19 Not connected PIN 20 DT R PIN 21~25 Not connected Use[...]

BTP-R880NP User’s Manual - 17 - ¾ Supports status back ¾ Supports parameter configuration ¾ Supports firmware update on-line ¾ Supports printer status query and interfac e module maintenance bas ed on HTTP(only JK-E02 interface supports, while JK-E 04 interface does not support) 2) Interface signal definition Interface adopts 10BASE-T standar[...]

BTP-R880NP User’s Manual - 18 - requested from the local di stributor or manufacture. 6.6 Power interface definition Power supply interface signal definition PIN Signal Name 1 E 2 L 3 N 24V power interface definition PIN Signal Name 1 E 2 L 3 N 6.7 Cashdrawer interface signal definition 1) Electrical features ¾ Driving voltage: DC 24 V ¾ Drivin[...]

BTP-R880NP User’s Manual - 19 - 7 T roubleshooting In case of printer fault, consult th is section for solutions and advice. If you do not find a solution in this section, pl ease contact your local dealer for assistance. 7.1 Printer doesn’t work Problems Possible causes Solution Printer has no power supply Connect the printer power Printer pow[...]

BTP-R880NP User’s Manual - 20 - 8. Accessories 8.1 Spill proof cover 8.2 HERALD – kitchen alarm system 8.3 Power Supply CASE This cover is used to install the AC power adapter under the printer; so that the power adapter would become an internal part of the printer (the pow er adapter will be inside of the printer). 8.4 Wall Mounting The printe[...]

BTP-R880NP User’s Manual - 21 - 2) Insert the plastic plugs in the holes and make su re that the plugs are fully inside the holes and do not stick out. 3) Screw the two screws in the plastic plugs and keep10mm spac e between the screw head and the wall surface. 4) Regulate the paper near end sensor (Please refer to 3.4.1) ,)Mount, Mount the print[...]

BTP-R880NP User’s Manual - 22 - 8.5 Cable for PoweredUSB Connections[...]

BTP-R880NP User’s Manual - 23 - 9. Power Management The power management of BTP-R880NP has four operation modes: Ready , Active, Sleep, Off. 1. Printer will enter into Ready mode after pow ering on printer or completing printing job. 2. Printer will enter into Sleep mode if there is not any printing job for 5 minutes in Ready mode. 3. Printer wil[...]

BTP-R880NP User’s Manual - 24 - APPENDIX A: Configuration setting function Parameter setting (configuring) by Feed button 1) Hold the FEED button pressed while switching the printer on. 2) After the printer has printed t he configuration sheet, pr ess and hold the FEED bu tton to configure the printer . The main menu for the key- stroke setting p[...]

BTP-R880NP User’s Manual 25 P ARAMETER SETTING BY FEED BU TTON MAIN MENU Exit ->1 Print Self T est ->2 Configuratio n ->3 CONFIGURA TION Exit W ithout Save ->1 Exit W ith Save ->2 Communication ->3 B ack T o Las t Menu ->1 USB Interface ->2 USB MODE:API MODE Back T o Last Menu ->1 WinDriver Mode ->2 API Mode ->3 S[...]

BTP-R880NP User’s Manual 26 Print '?' ->3 Rx Buff Size ->4 RX BUFFER SIZE :4K Bytes Back T o Last Menu ->1 4k Bytes ->2 45 Bytes ->3 64K Bytes ->4 Mechanism & Hardware ->4 HARDWARE SETTINGS Back T o Last Menu ->1 Mark Sensor ->2 MARK SENSOR: Disable Back T o Last Menu ->1 Enable ->2 Disable ->3 Cu[...]

BTP-R880NP User’s Manual 27 82.5mm ->6 Left Margin ->4 LEFT MARGIN:7mm Back T o Last Menu ->1 0mm ->2 1mm ->3 3mm ->4 5mm ->5 7mm ->6 9mm ->7 Right Margin ->5 RIGHT MARGIN:9mm Back T o Last Menu ->1 0mm ->2 1mm ->3 3mm ->4 5mm ->5 7mm ->6 9mm ->7 CR Command ->6 CR COMMAND: Disable Back T o Las[...]

BTP-R880NP User’s Manual 28 55% ->3 50% ->4 45% ->5 40% ->6 35% ->7 30% ->8 Gray Scale Mode ->10 Gray Scale Mode:Mode3 Back T o Last Menu ->1 Mode 0 ->2 Mode 1 ->3 Mode 2 ->4 Mode 3 ->5 Mode 4 ->6 Mode 5 ->7 Mode 6 ->8 Mode 7 ->9 Paper Senso r Settings ->6 P APER NEAR END SETTINGS Back T o Last M[...]

BTP-R880NP User’s Manual 29 Select UDFONTB ->5 Beep settings ->9 Beep settings: Disabled Back T o Last Menu ->1 Enable Ex ternal Herald ->2 Enable Int ernal buzzer ->3 BEEP MODE Back T o Last Menu ->1 Mode 1 ->2 Mode 2 ->3 Mode 3 ->4 Mode 4 ->5 Mode 5 ->6 All Beep disa bled ->4 Set Printer Mode ->10 Printer [...]