Northern Industrial Tools 9560CV инструкция обслуживания

INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com Angle Grinder 100 mm (4”) MODEL 9560CV 100 mm (4”) MODEL 9563CV 115 mm (4-1/2”) MODEL 9561CV 115 mm (4-1/2”) MODEL 9564CV 125 mm (5”) MODEL 9565CV DOUBLE INSULA TION[...]

2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA002-2 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shoc k, fire and/or s[...]

3 5. A void body contact with gr ounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. 6. Do not expose power tools to rain or wet conditions. W ater enter ing a po wer tool will increase the risk of electric shock. 7. Do not abuse the cor d. Never use the cord t[...]

4 24. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized par ts or f ailure to follo w Maintenance instructions may create a risk of electric shock or injury . USE PROPER EXTENSION CORD: Mak e sure your e xtension cord is in good condition. When using an e [...]

5 8. Be careful not to damage the spindle, the flange (especially the installing surface) or the lock n ut. Damage to these par ts could result in wheel breakage. 9. NEVER use tool with wood cutting bl ades or other sawblades. Suc h blades when used on a grinder frequently kic k and cause loss of control leading to per sonal injury . 10. Hold the t[...]

6 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Shaft lock CA UTION: • Ne ver actuate the shaft lock when the spindle is mo ving. The tool ma y be damaged. Press the shaft lock to pre vent spindle rotation when install- ing or removing accessori[...]

7 CA UTION: • If the tool is operated continuously at lo w speeds for a long time, the motor will get o verloaded and heated up. • The speed adjusting dial can be turned only as far as 5 and back to 1. Do not f orce it past 5 or 1, or the speed adjusting function ma y no longer work . The tools equipped with electronic function are easy to oper[...]

8 Loosen the le ver on the wheel guard. Mount the wheel guard with the protrusion on the wheel guard band aligned with the notch on the bearing box. Then rotate the wheel guard around 180 degrees. Tighten the le ver to f asten the wheel guard. If the le ver is too tight or too loosen to f asten the wheel guard, loosen or tighten the screw to adjust[...]

9 Installing or removing abrasive disc (optional accessory) NO TE: • Use sander accessories specified in this manual. These must be purchased separately . Mount the rubber pad onto the spindle. Fit the disc on the rubber pad and screw the loc k nut onto the spindle. T o tighten the lock n ut, press the shaft lock fir mly so that the spindle canno[...]

10 grinder in the B direction or it will cut into the workpiece. Once the edge of the wheel has been rounded off by use , the wheel ma y be wor k ed in both A and B direction. Operation with wire cup brush (optional accessory) CA UTION: • Check oper ation of br ush b y r unning tool with no load, insuring that no one is in front of or in line wit[...]

11 Operation with abrasive cut-off wheel (optional accessory) W ARNING: • When using an abrasiv e cut-off wheel, be sure to use only the special wheel guard designed fo r use with cut- off wheels. • NEVER use cut-off wheel f or side gr inding. During cutting operations, ne ver change the angle of the wheel. Placing side pressure on the cut-off [...]

12 guards as recommended in this manual. Y our failure to do so could result in personal injury to y ou and others. If you need an y assistance for more details regarding these accessories, ask your local Makita service center . 9560CV/9563CV 9561CV/9564CV 9565CV 1 Grip 36 2 Wheel guard 3 Inner flange 35 Inner flange 45 4 Depressed center grinding [...]

13 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut[...]

14 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade[...]

15 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy St. Fremont, CA 94538-5107 (510) 657-9881 14930 Northam St. La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Av enue Sacramento , CA 95825 (916) 482-5197 7674 Clair[...]

W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some e xamples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and o[...]