Nikon D80 инструкция обслуживания

Camera Housing – Model D80 (Nikon) User Manual Cont ent s: 1 . Introduction 2 . Specifications 3 . Set up Instructions 4 . Function Controls 5 . Use & Care of Housing 6 . Service 7 . Warranty 1 . Introduction 10 BAR Underwater Housings are small, light and rugged enough to be used on every dive. Use of clear polycarbonate allo ws for visual i[...]

2 . Specifications D80 Test Pressure 10 Bar (300 ft.) Ho usings are individually tested Closure Design Air Lock Body Material Polycarbonate Overall Size 220 x 300 x 230 mm (LxWxH) Total Weight Approximately 2.8 Kg (Housing only) Buoyancy (with camera) Approximately neutra l in salt water Features • Visible main O-ring for final pre-dive check •[...]

3 . Fu ncti on C ontro ls D8 0 1. Delete 2. Playback 3. Menu 4. Help / Protect 5. Thumbnail 6. Pl ayback zo om / Image qualit y & size 7. AE lock / AF lock 8. 9. 10. 11. Multi selector 12. O.K. 13. Main command dial 14. Pressure release plug 15. Viewfinder eyepiece 16. Shutter 17. Sub-command dial 18. Zoom control dial 19. Focus mode selector 2[...]

4.1 Air Lo ck: The body and lid are desig ned with the Air Lock System “no clip” closure arrangement. Testing has shown that this arrangement allow the water to ex ert an even pressure on the O-ring, Increase the reliabili ty of the watertight seal. 4.2 Pressure release plug To open the housing, the pressure release plug must be f irst unscrewe[...]

(Fig. 2) D80 Opening Key / Lever (Fig. 3) Turn to open 4.4 Special no te on respon sibility f or watertigh t integrit y: Each housing is individually inspected and hydrosta tically tested in the fact o ry. The design of the main piston O-ring seal is among the most reliable in the indus try and the watertig ht integrity is exce llent. This special [...]

straight away , rather than leaving it lyi ng aro und. Before replacing the lid, make sure that no contamination such as dust, hair, salt, sand etc. has fallen on to the O-ring or O-ring recess, as a precaution we recommend to inspect the O-ring ev ery time the lid is opened and to carry out the maintenance if nec essary. Procedure : • Place the [...]

(Fig. 7) (Fig. 8) (Fig. 9) Replace the lid (Fig. 8). Remember to ensure the pressure release plug is pulled all the way out while closing, otherwise the air cannot escape. Squeeze the lid closed all the way with the hissing of expe lled air. Screw home (CLOCKWISE ) the pressure release plug (Fig. 9). There is no need to excessively tighten this plu[...]

After replacing the lid, make a final visual inspecti on of the main O-ring for contamination (Fig. 10). (Fig. 10) Note: If the O-ring is in goo d contact, a thin black line, about 0.5 to 1mm in width should b e visible, where the O-ring is in contact wi th the lid. Foll ow this lin e all the way round the edge of the seal, as a final check that th[...]

5 . Use & Care of Housing: 5.1 Pre Dive Funct ion Check. Just before entering the water, make a habi t of reviewing that you have carried out the proper steps to close the housing. and the pressure release plug screwed home. Make a visual check of the O-ring seal. It is also us eful to switch o n the camera, and check that contro ls e.g. on/of [...]

5.5 Accidents. The impact resis tance of the housing is excellent . H owever after an accident the alignment of the housing may have been damaged. Therefore in the event of your ho using suffering an impact force, e.g. being dropped, it is essential you do not us e the housing for diving. Please return the housing immediately for service. Please pu[...]

7 . Warranty The warranty is valid within two years from the date of first purchase. The warrant y applies only to the housing itself. 10 BAR does not accept any liability either implicit or otherwise for any equipment housed inside, or used together with the housing. In the event of the housing flooding within the period of warranty, 10 BAR will r[...]