Newcon Optik LRB 4000CI инструкция обслуживания

10. QUALITY CERTIFICATE LRB 4000CI is suited for usage. Production date ____________________________ Serial number _____________________________ Device performance: Actual data Measured data Reflective object, m Non-reflective object, m Azimuth, ° Elevation, ° RS-232 interface Pass Quality Inspect or signature___________________ Purchase date ___[...]

IMPORTANT INFORMATION Read prior to activation You have just purchased a complicated electronic device. To operate it properly, please read this manual carefully. Here are some comm on precautions that must be noted. • NEVER subject the unit to im pact while operati ng or being transported • NEVER transport the unit without the case • NEVER d[...]

8. WARRANTY NEWCON OPTIK warrants this product against defects in material and workmanship for one year from the date of the original date of consumer's purchase, but no more than 18 months from the date of m anufacturing. If your Newcon product proves to be defective during this period, please bring the product securely packaged in its origin[...]

CONTENTS 1. Brief description 2. Appearance of the device 3. Supplied accessories 4. Technical characteristics 5. Operation instructions 5.1. Preparing the device for operation 5.2. Measuring procedure 5.3. Mode switching procedure 5.4. Gating distance selection 5.5. Additional display information 5.6. Computer interconnectivity 5.7. Test modes 6. [...]

6. STORAGE AND MAINTENANCE INSTRUCTIONS . Precautions: LRB is a sophisticated precision optical instrument equipped with electronics. Therefore, it should be handled with due care. • Keep your device away from direct sunlight, impacts, dust, moisture, and sudden changes of temperatures. • Do not keep the device at temperatures higher than 65 o [...]

2. APPEARANCE OF THE DEVICE 1 – Eyepieces; 2 – Objective lens – receiving lens; 3 – Objective lens - emitting lens; 4 – Dioptric correctio n rings; 5 – Mo de button; 6 – Action button; 7 – B ody of the device; 8 – Rubber gri p Fig. 1 6 5.6. Computer interconnectivity The unit is equipped with standard RS-232 interface. The data is[...]

There are four statistical qualifications of the reflected signal: • NO TARGET REFLECTION – when a steady reflected signal isn’t received. Numerical display shows four dashes at the distance displaying area; • TARGET REFLECTION LOW – when the number of steady received reflected signals is just enough to make acceptable conclusion about th[...]

7 4. TECHNICAL CHARACTERISTICS 1. Optics Magnification, x Objective Lens, mm Exit Pupil Diameter, mm Field of View Type of Coating Interpupilary distance, mm Diopter adjustment range Axial Resolution, ” Image tilt, maximum - Horizontal - Vertical 7 50 7.1 5 ° Fully multi-coated optics 58-72 ±4 6 60” 30” 2. Range Finder Type Measuring Range,[...]

M/° - units of angular measurement: m ils or degrees Shape of the reticle: cross shape or rectangular shape (2). rEC1 - recall function. Upon pressing the Action button (6) (fig. 1) the Display will sequentially show results of last 10 measurements, starting from the latest one. The number appearing after word " rEC " shows the number of[...]

5. OPERATION INSTRUCTIONS Liquid Crystal Display (LCD) 1 – Low battery indicat or; 2 – Reticle (cross or rectangular selectable); 3 – Units of measurem ent (Yards, Mete rs, KMH, MPH, Mils or Degrees); 4 – Measur ement result; 5 – Target quality ind icator; 6 – Laser active ind icator 7 – Over 100m gating i ndicator, 8 – Setup m ode [...]

override reticle type and target selection with the sub selection code. For example, Standard 1 mode im plies cross reticle. If you choose rectangular reticle (sub selection code 10), you change the reticle shape and leave all ot her parameters of this mode intact. If then you choose Standard1 again, the reticle will turn back crosshair. The last s[...]

The mode selection logic allows choosing the nearest (‘first’), the farthest (‘last’) or the most reflective (‘auto’) target. Besides, you can exclude all targets that are closer than the predefined distance (gating distance selection, see below). 5.3. Mode switching procedure By pressing M button (5) (Fig.1) when the System is in READY[...]

Fig.4 Mode switching trek Mode Screen display Dis t anc e Spee d H orizontal Angl e Ver t ic al Angl e Ret ic le Tar get Typ e 1) Standar d 1 M Select this mode Go to next mode A , , , Meter Degree Degree 1) Standard 2 M Go to next mode A , , , Meter Mills Mills Codes 3) A M Go int o sub menu Code 1 A M Meter Code 2 A M Go to next mode Yard Code 3 [...]