NEC LCD400 инструкция обслуживания

MultiSync ® LCD 400 ™ LCD 2000 ™ User’s Manual Contents 1 Quick Start 2-3 Controls 4-5 Recommended Use 6-7 Specifications 8-9 Features 10 Troubleshooting 11 References 12 Limited Warranty 13 MultiSync ® LCD 400 ™ LCD 2000 ™ User’s Manual 78132391 10/29/99, 8:42 AM 1[...]

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARN[...]

MultiSync LCD 2 0 0 0 M u l t i S y n c L C D 4 0 0 Contents 1 Your new NEC Technologies MultiSync ® LCD monitor box* should contain the following: • MultiSync LCD Monitor with tilt/swivel base MultiSync LCD 400 ™ monitor, LA-1421JMW or MultiSync LCD 2000 ™ monitor, LA-2031JMW • Power Cord • Video Signal Cable (LCD 400 ) • 15-pin VGA t[...]

Quick Star t To attach the MultiSync ® LCD monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. For the PC: Connect the 15-pin mini D-SUB of the appropriate signal cable to the connector of the display card in your system (Figure A.1) . Tighten all screws. For the Mac: Connect the MultiSync LCD 400 ™ or M[...]

H/CS VS R G/Sync B Quick Star t 3 Figure F.1 Figure D.1 Figure C.1 Figure E.1 MultiSync LCD 400 monitor MultiSync LCD 2000 monitor MultiSync LCD 400 monitor MultiSync LCD 2000 monitor Power Switch Power Switch 15-pin mini D-SUB 78132391 10/29/99, 8:42 AM 5[...]

4 OSM ™ (On-Screen-Manager) Controls The OSM controls on the front of the monitor function as follows: Control Main Menu Sub-Menu EXIT Exits the OSM controls. Exits to the OSM controls main menu. CONTROL / Moves the highlighted Moves the highlighted area area up/down to select up/down to select one of the one of the controls. controls. CONTROL ?[...]

5 Controls AccuColor ™ Control System Color presets select the desired color setting. If a setting is adjusted, the name of the setting will change to Custom . Color Gain (Red, Green, Blue): Increases or decreases Red, Green or Blue color depending upon which is selected. The change in color will appear on screen and the direction (increase or de[...]

Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTISYNC ® LCD COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service [...]

CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: Recommended Use • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downwar[...]

Specifications 8 Monitor MultiSync ® LCD 400 ™ Notes Specifications Monitor LCD Module Diagonal: 14.1 inch Active matrix; thin film transistor (TFT) Viewable Image Size: 14.1 inch liquid crystal display (LCD); 0.28 mm dot Native Resolution (Pixel Count): 1024 x 768 pitch, XtraView™ technology; 180cd/m 2 white luminence; 100:1 contrast ratio, t[...]

9 Monitor MultiSync ® LCD 2000 ™ Notes Specifications Monitor LCD Module Diagonal: 20.1 inch Active matrix; thin film transistor (TFT) Viewable Image Size: 20.1 inch liquid crystal display (LCD); 0.31 mm dot Native Resolution (Pixel Count): 1280 x 1024 pitch, XtraView™ technology; 150cd/m 2 white luminence; 100:1 contrast ratio, typical Input [...]

10 Features Analog Advantage: Capable of displaying unlimited colors in a continuous spectrum, providing a truer representation of color. The monitor’s high contrast LCD enhances color vibrancy and improves focus with no geometric distortion. Wider Compatibility: Because the MultiSync LCD monitor is analog through and through, it does not require[...]

11 T roubleshooting No picture • The signal cable should be completely connected to the display card/computer. • The display card should be completely seated in its slot. • Power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display card or system being use[...]

12 References • BBS (508) 635-4706 NEC Technologies’ Remote Bulletin Board System is an electronic service accessible with your system and a modem. Communication parameters are: 300/1200/2400/9600/14.4k/28.8k/33.3k bps, no parity, 8-data bits, 1 stop bit • Customer Service/ Technical Support (800) 632-4662 Fax (508) 635-4298 • Electronic Ch[...]

NEC Technologies, Inc. (hereinafter “NECTECH”), warrants this Product to be free from defects in material and workmanship and, subject to the conditions set forth below, agrees to repair or replace any part of the enclosed unit, other than the LCD backlight, which proves defective for a period of three (3) years from the date of first consumer [...]

NEC LCD Series Part No. 78132391 Printed in Japan PROPRIETARY NOTICE AND LIABILITY DISCLAIMER The information disclosed in this document, including all designs and related materials, is the valuable property of NEC Technologies and/or its licensors, as appropriate, reserve all patent, copyright and other proprietary rights to this document, includi[...]