MTD 500, 510 инструкция обслуживания

PRINTED IN U .S.A. FORM NO . 770-10509 E.fm (5/2004) Oper ator’ s Man ual Log Splitter Model Series 500 & 510 IMPORT ANT : Read saf ety rules and instr uctions ca refully bef ore operating equipment. Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest- covered, brush-covere[...]

2 TABLE OF CONTENTS FINDING MODEL NUMBER This Operator’s Ma nual is an important part of your new log splitter. It will help you assemb le, prepare and maintain the unit fo r best performance. Plea se read and understand wh at it says. Before you star t assembling your new equipment , please locate t he model plate on the equipment and copy th e [...]

3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES General Practices 1. Read, understand, and follow all instructi ons on the machine and in the manual(s) before attempti ng to assemble and ope rate. Keep this manual in a safe place for future and regular re ference and for o rdering replacement parts. 2. Be familiar with all controls and proper opera[...]

4 Operation 1. Before starting th is machine, review the “Safety Instructions”. Failure to foll ow these rules may result in serious injury to the operator or bystanders. 2. Never leave this machi ne unattended with the en gine running. 3. Do not ope rate machine while u nder the infl uence of alcohol, drugs, o r medication. 4. Never allow anyo[...]

5 SECTION 2: ASSEMBLING YOUR LOG SPLITTER Unpacking from Cr ate • Pry top, sid es, and en ds off the crate. Set pan els aside to avoid tire punct ure or personal injury. • Remove and discard plastic ba g that covers unit. • Remove any loose par ts if included with unit (i.e., operator’s manu al, etc.) • Cut and remove st raps which secure[...]

6 • Disconnect the lo g cradle from the beam on th e side of the control valve. See Figure 4. Figure 4 • Lift and slid e the cylinder up to the top of beam and into the weld brackets. • Attach the dislodger over the wedge assembly and secure with hard ware, previous ly removed, to the weld brackets. See Figure 5. NOTE: Once the six hex screws[...]

7 SECTION 3: KNOW YOUR LOG SPLITTER Compare the illustration in Fi gure 7 below with the controls on your log splitter, and get familiar with its features before start ing to operate. Know how to stop t he machine quickly in the event of an em ergency. Figure 7 Control Handle The control handle has three positio ns. See Figure 7. • FORWARD: Move [...]

8 SECTION 4: OPERATING YOUR LOG SPLITTER Gas and Oil Fill-Up • Service the engine with gasoline an d oil as instructed in the en gine manual packed with your log splitter. Read in structions carefully. IMPORT ANT : Your log splitter is shippe d with motor oil in the engi ne. Howev er, you MUST check the oil level before operating. Be ca reful not[...]

9 • To lock the beam in th e vertical position, pull out on the vertical beam lock and rotate it to secur e the beam. See Figure 7. • Stand in fron t of the unit to operate the control handle and to stabilize th e log. See Figure 8A. Figure 8 Horizontal Position • Pull the vertical beam lock out and rotate it down. See Figure 7. Pivo t beam t[...]

10 NOTE: Use caution when backing up. It is recommended to use a spotter outside the vehicle. SECTION 5: ADJUSTING YOUR LOG SPLITTER We d g e A s s e m b l y As normal wear occurs and there i s excessive “play” between the wedge and be am, adjust the bolts on the side of the wedge assembly to eliminate excess space between the wedge and t he be[...]

11 • Maintain flu id level at all times wit hin the range specified on the dipstick, or within 3- 3.5” from top edge of the pipe . • Change the hydr aulic fluid in the reservoir every 100 hours of ope ration. • Disconnect the suction ho se from the bottom of the reservoir tank and dra in the fluid into a suitable container. Refill using on [...]

12 SECTION 7: STORING YOUR LOG SPLITTER Prepare your log splitter for st orage at the end of the season or if the log splitter will not be used for 30 days or more. • Clean the log splitter thor oughly. NOTE: We do not recommend the use of pressure washers or garden hose to clea n your unit. They may cause damag e to the log splitter co mponents,[...]

13 Hydraulic Cylinder: T roubleshooting NOTE: For repa irs beyond thos e listed here, contac t your neares t authorized servic e center. Prob lem Cause Remedy Cylinder rod will not move 1. Broken drive shaft. 2. Shipping plu gs left in hydr aulic hoses. 3. Set screws in coupling not adjusted properly. 4. Loose sha ft coupling. 5. Gear sections dama[...]

14 SECTION 9: PARTS LIST FOR MODEL SERIES 500 AND 510 1 2 3 4 5 6 7 8 9 80 11 12 13 14 15 16 17 18 19 20 21 10 22 23 24 25 23 26 27 28 29 30 33 18 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 23 51 52 53 54 55 56 57 44 58 59 41 61 44 44 62 63 64 66 66 65 67 68 68 69 70 A A B B C C 31 71 40 44 50 41 59 79 77 75 73 74 78 48 81 41 59 63 66 76 32[...]

15 Model Series 500 and 510 Ref. No. P ar t No. P art Description 1. 718 -0773 Hydraulic Cylinder 2. 727 -0634 Hydraulic T ube 3. 710 -1018 He x Cap Screw 1/2-20 x 2.75 4. 737 -0192 90 Degree Solid Adapter 5. 718 -0481 Control V alve 6. 737 -0153 Retur n Elbow 7. 737 -0238 Nipple Pipe 1/2-14 8. 710 -1806 He x Cap Screw 1/2-13 x 3.25 9. 719 -0550 W [...]

MANUF A CTURER’S LIMITED W ARRANTY FOR: The limited warranty set forth below is given by MTD LLC with respect to new merchandise purchased and used in the United States, its poss essions and territories. “MTD”warrants this product ag ai nst defects in material and workmanship for a period of two (2) years commen cing on the date of original p[...]