Mitsubishi Electronics HC7000 инструкция обслуживания

LCD PROJECTOR This User Manual is important to you. Please r ead it befor e using your pr ojector . MODEL HC7000 User Manual HC7000[...]

EN-2 The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literatur e accompanying the appliance. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICE[...]

EN-3 Note: This symbol mark is for EU countries only . This symbol mark is according to the dir ective 2002/96/EC Article 10 Information for users and Annex IV , and/or to the directive 2006/66/EC Article 20 Information for end-users and Annex II. Declaration of Conformity Model number: HC7000 T rade name: MITSUBISHI ELECTRIC Responsible party: Mit[...]

EN-4 Please read all these instructions r egar ding your projector and r etain them for futur e refer ence. Follow all warnings and instructions marked on the projector . Read instructions All the safety and operating instructions should be read befor e the appliance is operated. Retain instructions The safety and operating instructions should be r[...]

EN-5 WARNING: Unplug immediately if there is something wr ong with your projector . Do not operate if smoke, strange noise or odor comes out of your projector . It might cause fi re or electric shock. In this case, unplug immediately and contact your dealer . Never remove the cabinet. This projector contains high voltage cir cuitry . An inadverten[...]

EN-6 2 3 Checking accessories The following accessories are pr ovided with this pr ojector . Check to be sure that all of the accessories ar e packed in the package. Cables Mini D-SUB 15-pin Mini D-SUB 15-pin D-SUB 9-pin D-SUB 9-pin RGB cable for PC (246C521-10) RS-232C cable (246C548-10) Used for projector contr ol by computer . •  Power supp[...]

EN-7 Overview VIDEO IN and S-VIDEO IN terminals COMPONENT VIDEO IN terminals COMPUTER IN/COMPONENT VIDEO IN terminal (mini D-SUB 15-pin) HDMI IN-1 terminal (HDMI 19-pin) HDMI IN-2 terminal (HDMI 19-pin) SERIAL terminal (D-SUB 9-pin) Used for projector contr ol by computer . Contact your dealer for details. TRIGGER terminal Used for the optional ele[...]

EN-8 Remote contr ol ON ( I ) button HDMI2 button HDMI1 button COMPONENT button A V MEMOR Y buttons ENTER button MENU button CONTRAST button* BRIGHTNESS button* GAMMA button* ZOOM/FOCUS button LENS SHIFT button NOISE REDUCTION button* COLOR button* SHARPNESS button* COLOR TEMP . button* ASPECT button AUTO IRIS button S , T , W , X buttons VIDEO but[...]

EN-9 30° 30° 30° 30° Operational range of the r emote contr ol V ertical directions (ceiling mount) Reception angle V ertical directions When operating the remote contr ol, keep the distance from the r emote contr ol to the projector via the scr een within about 5 m (15 feet). The operable range of the remote contr ol, however , depends on the [...]

EN-10 Setting up your pr ojector Setting up the scr een Install the screen perpendicularly to the pr ojector . If the screen can not be installed in such a way , adjust the projection angle of the pr ojector . (See page 12.) Install the screen and pr ojector so that the pr ojector’ s lens is placed at the same height and horizontal position of th[...]

EN-11 Setting up your pr ojector (continued) Scr een size and pr ojection distance (continued) Screen width (SW) Down side Up side 50% 50% Screen Screen height (SH) H1 H1 L Right side Left side W1 W1 When the aspect ratio of the screen is 4:3 When the aspect ratio of the screen is 4:3, the positional r elation between the projected image and the sc[...]

EN-12 Adjusting the position of the pr ojected image T o adjust the position of the projected image on the screen, use the LENS SHIFT button. Press the LENS SHIFT button. The LENS SHIFT menu appears at the center of the screen. Press the S , T , W or X button to move the image position. When the T button is pressed, the image moves down. When the S[...]

EN-13 Fr ont pr ojection, ceiling mounting For ceiling mounting, you need the ceiling mount kit designed for this projector . Ask a specialist for installation. For details, consult your dealer . The warranty on this projector does not cover any damage caused by use of any non-recommended ceiling mount kit or installation of the ceiling mount kit i[...]

EN-14 DVD player A. Connecting the pr ojector to video equipment When the projector and the connected devices ar e located too close to each other , the projected image may be affected by their interfer ence. See the owner’ s guide of each device for details about its connections. Preparation: Make sure that the power of the pr ojector and that o[...]

EN-15 1 2 1 2 Connect one end of the optional video cable to the VIDEO IN terminal of the projector . Connect the other end of the video cable to the video output terminal of the video equipment. 1. 2. Also read the instruction manual of the equipment to be connected. Contact your dealer for details of connection. When a TV tuner or VCR is connecte[...]

EN-16 Connecting to video equipment having a HDMI terminal Y ou can project high-quality images by connecting the HDMI IN terminal of this projector to video equipment having a HDMI output terminal. In addition, this projector supports HDCP and is able to r eceive encrypted digital video data that are output fr om DVD players. Select HDMI as the in[...]

EN-17 B. Plugging in the power cor d In order to ensur e the safety in case of trouble with the projector , use an electrical outlet having an earth leakage breaker to supply the power to the pr ojector . If you do not have such outlet, ask your dealer to install it. • The power cords for use in the U.S. and Eur ope are included with this project[...]

EN-18 Confi rm the POWER indicator lights-up r ed. If the projector was turned off befor e the lamp had cooled down suffi ciently , the fan may start rotating and the POWER button may not work after the power cord is plugged. (The ST A TUS indicator blinks green.) After the fan stops rotating, pr ess the POWER button to tur n back on the POWER in[...]

EN-19 Press the POWER button on the pr ojector or the OFF ( ) button on the remote contr ol. A confi rmation message is displayed. T o cancel the procedure, leave the pr ojector for a while or press the MENU button. Press the POWER button on the pr ojector or the OFF ( ) button on the remote contr ol again. The lamp goes out and the projector goes[...]

EN-20 Viewing video images (continued) Setting the aspect ratio Y ou can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Change the setting according to the type of the input video signal. : Signal size : Image area Setting Original image size 4:3 16:9 ZOOM1 ZOOM2 STRETCH ANAMORPHIC1 ANAMORPHIC2 Asp[...]

EN-21 How to change the settings: With the remote contr ol: Press the ASPECT button. Every time the ASPECT button is pressed, the aspect mode changes fr om AUTO to 4:3, 16:9, to ZOOM1, to ZOOM2, to STRETCH, to ANAMORPHIC1, to ANAMORPHIC2, and back to AUTO. Some modes are not available with certain signals. With the FEA TURE menu: (See page 26 for m[...]

EN-22 2 1 A. Connecting the pr ojector to a computer Preparation: Make sure that the power of the pr ojector and that of the computer are turned off. When connecting the projector to a desktop computer , disconnect the RGB cables that are connected to the monitor . • • Connect one end of the supplied RGB cable to the COMPUTER IN/COMPONENT VIDEO[...]

EN-23 Confi rm the POWER indicator lights-up r ed. If the projector was turned off befor e the lamp had cooled down suffi ciently , the fan may start rotating and the POWER button may not work after the power cord is plugged. (The ST A TUS indicator blinks green.) After the fan stops rotating, pr ess the power button to tur n back on the POWER in[...]

EN-24 Viewing computer images (continued) Press the LENS SHIFT button. The LENS SHIFT menu appears at the center of the scr een. Press the S or T button to adjust the vertical position and W or X button to adjust the horizontal position of the displayed image. When the projector cannot be positioned perpendicularly to the scr een, adjust the projec[...]

EN-25 Menu operation Menus are not displayed when no signal is supplied to the pr ojector . IMAGE GAMMA MODE AUTO, SPORTS, VIDEO, CINEMA USER1 REFERENCE SPORTS, VIDEO, CINEMA USER2 ADJUST MODE ALL, RED, GREEN, BLUE CONTRAST ±30 HIGH ±10(R) ±10(G) ±10(B) BRIGHTNESS ±30 MID ±10(R) ±10(G) ±10(B) COLOR TEMP . HIGH BRIGHTNESS LOW ±10(R) ±10(G)[...]

EN-26 How to set the menus: The following describes how to set AUTO POWER OFF time as an example. Press the MENU button. IMAGE opt. A V MEMORY 1 Press the W or X button to select a menu to use. INS T ALL A TION opt. A V MEMO R Y 1 Press the ENTER button (or T button). opt. A V MEMORY 1 INST ALLA TION KEYSTONE 0 1. 2. 3. 1. IMAGE menu ITEM SETTING F[...]

EN-27 2. INST ALLA TION menu ITEM SETTING FUNCTION KEYSTONE ±15 Use to corr ect vertical keystone distortion. LAMP MODE ST ANDARD Select this option when you want to view images in a well-lit room. LOW Select to moderate the intensity of the lamp. The fan operating sound is reduced and the lamp lifetime becomes longer . AUTO POWER ON ON / OFF When[...]

EN-28 3. FEA TURE menu FE A TURE AUTO AUTO AUTO opt. MENU POSITION CINEMA MODE VIDEO SIGNAL ? ASPECT RESET ALL English LANGUAGE A Ë OFF AUTO OK DISPLA Y INPUT P ASSWORD FUNCTION 1. MENU DIMMER A V MEMO R Y 1 SETUP SCART INPUT OFF Menu operation (continued) 3. FEA TURE menu ITEM SETTING FUNCTION ASPECT AUTO Select to change the aspect ratio automat[...]

EN-29 4. SIGNAL menu 5. USER menu R G B R G B SIGNAL HORIZ. POSITION 0 VERT . POSITION 0 TRACKING 0 COMPUTER INPUT AUTO FINE SYNC. 0 USER opt. OK ON HOLD 100% OVER SCAN A V MEMO R Y 1 CLAMP POSITION USER 1 CLAMP WIDTH 1 LPF OFF SHUTTER(U) 0 SHUTTER(L) 0 VERT . SYNC AUTO ? SHUTTER(LS) 0 SHUTTER(RS) 0 Menu operation (continued) 4. SIGNAL menu ITEM SE[...]

EN-30 6. INFORMA TION menu Menu operation (continued) INFORMA TION opt. LAMP TIME(LOW) INPUT RESOLUTION VERTICAL FREQUENCY HORIZONT AL FREQUENCY SYNC. TYPE 5wir e 60.02 KHz 75.04 Hz 1024X768 COMPUTER 0 H R G H V B 6. INFORMA TION menu ITEM DESCRIPTION LAMP TIME(LOW) This item shows a lamp operating time (hour) calculated based on that LAMP MODE is [...]

EN-31 T o adjust the brightness (CONTRAST and BRIGHTNESS): Y ou can make adjustments for the brightness of the projected image using the menu. (See page 26 for menu setting.) Display the IMAGE menu. Select CONTRAST or BRIGHTNESS by pressing the S or T button. Adjust the selected item by pressing the W or X button. T o cancel the menu: Press the MEN[...]

EN-32 T o adjust the tone of white (COLOR TEMP .): Y ou can select a preset color temperature (white tone) using the menu. (See page 26 for menu setting.) Display the IMAGE menu. Select COLOR TEMP . by pressing the S or T button. Select your desired color temperatur e by pressing the W or X button. The color temperature of each option is as follows[...]

EN-33 Adjusting pr ojected images (continued) T o adjust the ratio of change in brightness (GAMMA MODE): Y ou can select a preset gamma mode using the menu. (See page 26 for menu setting.) Display the IMAGE menu. Select GAMMA MODE by pressing the S or T button. Select your desired gamma mode by pr essing the W or X button. T o cancel the menu: Pres[...]

EN-34 This projector automatically and pr operly projects video signals supplied from the computer . However , some video signals may not be projected, depending on the type of the computer . In such a case, press the AUTO POSITION button. (See page 24.) When the signal is still not projected pr operly , adjust the projected image using the SIGNAL [...]

EN-35 Password function This projector is equipped with the passwor d function that is designed for prevention of theft and wr ong operation by children and r estriction on operation by other than specifi ed users. The passwor d function has two modes as follows. DISPLA Y INPUT .......... When the projector is turned on, the startup screen (or spl[...]

EN-36 This projector is equipped with a lamp to pr oject images. This lamp is a consumable. It may bur n out or its brightness may decrease during use. In such cases, r eplace the lamp with a new one as soon as possible. Be sure to replace the lamp with a new lamp sold separately that is exclusive to this projector . Contact your dealer for purchas[...]

EN-37 Replacing the lamp (continued) T o replace the lamp: Unplug the power cord. Loosen two screws (a) using a Phillips scr ewdriver (+) and remove the left side panel fr om the projector . (a) Loosen the screw (b) using a Phillips scr ewdriver (+), and remove the lamp cover (c). (b) (c) Loosen the screws (d) using a Phillips scr ewdriver (+). (d)[...]

EN-38 When removing the lamp fr om the ceiling-mounted projector When removing the lamp fr om the ceiling-mounted projector , use the lamp replacement tray packed with the projector or option lamp to pr event glass fragments from scattering. Assemble the lamp replacement tray accor ding to the procedure shown on it. Follow steps 1 to 5 on page 37. [...]

EN-39 W ar ning: Never use fl ammable air duster or other materials when cleaning the air -fi lter . Flammable substances may ignite causing fi r e or breakdown when the lamp is illuminated. Do not use fl ammable solvents (benzene, thinner , etc.) and fl ammable aerosols when cleaning the pr ojector body and lens. Flammable substances may igni[...]

EN-40 Before asking for r epair of the projector , check the following. If the symptom persists, stop using the projector , be sure to unplug the power plug, and then contact your dealer . No image appears on the screen. Problem Solution Power can not be turned on. Check whether the indicators are on or of f and how they are lightning. POWER ST A T[...]

EN-41 No image appears on the screen. (continued) Problem Solution The screen for entering the password appears. P ASSWORD FUNCTION in the FEA TURE menu has been set to DISPLA Y INPUT to enable the password lock. Enter the password or contact the person in char ge of management of the projector . (See page 35.) • J “NO SIGNAL” is displayed. T[...]

EN-42 Others Problem Solution The exhaust vents emit warm air . This air comes out after cooling the inside of the projector . Y ou may feel hot, but this is not a malfunction. • The menu can’t be used. The microcomputers inside the pr ojector may be wrongly operating because of noise. Press the POWER button to turn off the lamp and wait about [...]

EN-43 Normal condition POWER ST A TUS CONDITION NOTE Steady red Off Stand-by Steady green Blinking green Lamp stand-by (about 1 minute) The POWER button cannot be used to switch between on and off. Steady green Steady green The power is on. (Normal condition) Abnormal condition POWER ST A TUS CONDITION POSSIBLE SOLUTION Steady green or Steady red B[...]

EN-44 The specifi cations and outside appearance of the pr ojector are subject to change without prior notice. T ype LCD pr ojector Model HC7000 Display technology 0.74-inch LCD panel: 3 pieces (for R, G, B) (aspect ratio 16:9) Pixel: 1920 x 1080 = 2073600 pixels T otal 6220800 pixels Projection lens F 2.5 - 3.1 f= 23.5 - 37.6 mm Light-source lamp[...]

EN-45 *1: When ASPECT in the FEA TURE menu is set to AUTO. *2: Available for the signal fr om the HDMI IN terminal. Important: Some computers aren’ t compatible with the projector . The projector’ s maximum resolution is 1920 x 1080 pixels. It may not display images of higher resolutions than 1920 x 1080 correctly . If the resolution and fr equ[...]

EN-46 Specifi cations (continued) Connectors SERIAL (D-SUB 9-pin) 1 5 6 9 Pin No. Name I/O 1– – 2 TXD IN 3 RXD OUT 4– – 5 GND – 6– – 7– – 8– – 9– – COMPUTER IN/COMPONENT VIDEO IN (Mini D-SUB 15-pin) Pin No. Spec. 1 R(RED)/P R /C R 2 G(GREEN)/Y 3 B(BLUE)/P B /C B 4 GND 5 GND 6 GND 7 GND 8 GND 9 DDC 5V 10 GND 11 GND 12 DDC [...]

1 Zusho Baba, Nagaokakyo-City , Kyoto Japan M I T SUBIS HI ELECTRIC CORPORA T I O N A Mitsubishi Pr ojector W arranty , Sales Support and Service Information North America MDEA (Mitsubishi Digital Electronics America, Inc.) Presentation Products Division 9351 Jeronimo Road Irvine CA 92618, USA For Warranty Registration, visit: http://www .mitsubish[...]