Metrik Mobile Electronics MCD-479 инструкция обслуживания

PLL SYNTHESIZER STEREO RADIO WITH COMP A CT DISC PLA YER DIGIT AL + – OWNER'S MANU AL MCD-479[...]

2 INST ALLA TION Notes: • Choose the mounting location where the unit will not interfere with the normal driving function of the driver . • Before completly installing the unit, connect the wiring temporarily and make sure it is functioning properly. • Use only the parts included with the unit to ensure proper installation. The use of unautho[...]

3 1. Dashboard 2. Nut (5mm) 3. Spring washer 4. Screw (5 x 25mm) 5. Screw 6. Strap Be sure to use the strap to secure the back of the unit in place. The strap can be bent by hand to the desired angle. 7. Plain washer Removing the unit 1. Frame 2. Insert fingers into the groove in the front of frame and pull out to remove the frame. (When re-attachi[...]

HOW TO REMOVE AND INST ALL THE FRONT P ANEL 1. Press the release button and pull-off the front panel. Place the front panel into the supplied case to protect it. 2. T o install the front panel, insert the right side of thepanel into the housing first, then press the left side in until it locks in place. If the panel is not correctly installed some [...]

5 WIRING CONNECTIONS 1. All connections should be soldered and insulated with electrical tape. 2. Be sure to connect the red power input lead to + 12V power terminal after all the other leads have been properly connected. 3. Run all ground wires to a common ground. 4. After all the connections are completed, press the “RESET” (26) button. ANTEN[...]

6 + – 25 6 9 8 12 10 13 4 7 5 18 19 20 17 24 15 1 14 2 16 11 3 21 22 23 Basic Operation 1.0 ON/OFF Press PWR button (1) to turn on. Press PWR again to turn it off. 2.0 Select Mode Press SEL button (2) to move display through volume, bass, treble, balance and fader functions. Use + (3) and – (4) buttons to adjust the selected mode. When mode has[...]

7 8.0 Mute Press MUTE (13) to silence the receiver . Press again to resume listening. 9.0 Set the Clock 10.1 Press and hold DSP button (1 1) for three seconds until the display flashes. 10.2 Press (7) to change hours, (6) to change minutes. 10.0 Release Press REL button (25) until "tack" sound is heard, then the left-hand side of the pane[...]

8 Radio Operation 1.0 Select a Band Press BND button (5) to change between three FM bands and AM/L W bands. Each band stores up to six preset stations. 2.0 Select a Station T ouch a TUNE button (7) or (6) for less than two seconds to move radio frequency number down or up on step. Hold a TUNE button (7) or (6) for more than two seconds to seek the [...]

9 CD Player Operation 1.0 Insert and Eject CD Insert a CD into the loader slot. The CD will begin to pla y . Press (eject) (10) to stop CD play and eject the CD. The Receiver automatically switches to radio operation. 2.0 Skip T racks Press TUNE (7) or (6) to advance CD to next track. T rack numbers show on display . 3.0 Pause CD During CD player o[...]

10 SPECIFICA TION GENERAL Power Supply Requirements : DC 12 V olts, Negative Ground ONLY Chassis Dimensions : 178 (W) X 155 (D) X 50 (H) Tone Controls - Bass (at 100 Hz) : +10 dB/ – 10 dB - T reble (at 10 KHz) : +10 dB/ – 10 dB Maximum Output Power : 25W X 4 (ch) CD PLA Y ER Signal to Noise Ratio : < 60 dB Channel Separation : < 60 dB Fre[...]

11 TROUBLE SHOO TING Be f ore going through the che c k list, check all wiring connections. If any of the problems persist after check list has been completed, consult your Metrik deale r . Symptom Cause Solution No power . The car ignition is not If the power supply is properly on. connected to the car accessor y terminal, switch the ignition key [...]

88-06902-37 L I M I T E D O N E Y E AR W ARRAN T Y This warranty shall be in e ffect for a period of one year fro m the date of the first consumer purchase. This w arranty is valid during the warranty period providing that proo f of date of purchase fro m an authorized deale r is presented whenever warranty service is required. To receive serv ice [...]