Makita HP2010N инструкция обслуживания

INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com Hammer Drill 20 mm (3/4”) MODEL HP2010N DOUBLE INSULA TION[...]

2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA002-2 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shoc k, fire and/or s[...]

3 Electrical Safety 4. Double insulated tools are equipped with a polarized plug (one blade is wider than the other .) This plug will fit in a polarized outlet only one wa y . If the plug does not fit fully in the outlet, re verse the plug. If it still does not fit, contact a qualified elec- trician to install a polarized outlet. Do not change the [...]

4 21. Check f or misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation. If damaged, have the tool ser- viced before using. Many accidents are caused by poorly maintained tools. 22. Use only accessories that are recom- mended by the manufacturer f or your model. Accessories that may b[...]

5 4. Keep hands awa y from rotating parts. 5. Do not leave the tool running. Operate the tool only when hand-held. 6. Do not touch the bit or the w orkpiece immediately after operation; the y may be extremely hot and could b urn your skin. 7. Some material contains chemicals which may be to xic. T ake caution to prevent dust inhalation and skin con[...]

6 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Switch action CA UTION: • Bef ore plugging in the tool, always chec k to see that the s witch tr igger actuates properly and retur ns to the “ OFF ” position when released. • Switch can be lo[...]

7 Speed change T wo speed ranges can be preselected with the speed change le ver . T o change the speed, press the speed change lev er and slide it to the “ L ” position f or low speed or the “ H ” position f or high speed. If the speed change le ver does not slide easily , turn the chuck slightly in either direction while sliding the lev e[...]

8 Installing or removing drill bit T o install the bit, place it in the chuck as far as it will go . Tighten the chuck b y hand. Place the chuck k ey in each of the three holes and tighten clockwise . Be sure to tighten all three chuck holes e venly . T o remove the bit, turn the chuck k ey counterclockwise in just one hole, then loosen the chuc k [...]

9 Blow-out b ulb (optional accessor y) After drilling the hole, use the blo w-out bulb to clean the dust out of the hole. Drilling operation CA UTION: • Pressing e xcessively on the tool will not speed up the drilling. In fact, this e xcessive pressure will only serve to damage the tip of your bit, decrease the tool perf or mance and shor ten the[...]

10 MAINTENANCE CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore attempting to perform inspection or maintenance. T o maintain product SAFETY and RELIABILITY , repairs, car- bon brush inspection and replacement, any other mainte- nance or adjustment should be perf or med by Makita A uthor ized or F actor y Ser vice C[...]

Memo 11[...]

Memo 12[...]

13 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut[...]

14 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade[...]

15 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy St. Fremont, CA 94538-5107 (510) 657-9881 14930 Northam St. La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Av enue Sacramento , CA 95825 (916) 482-5197 7674 Clair[...]

W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some e xamples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and o[...]