Makita HM0860C инструкция обслуживания

INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com Demolition Hammer MODEL HM0860C 004479 DOUBLE INSULA TION[...]

2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA002-2 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shoc k, fire and/or s[...]

3 6. Do not expose power tools to rain or wet conditions. W ater enter ing a po wer tool will increase the risk of electric shock. 7. Do not abuse the cor d. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediatel y . Damaged cords increase t[...]

4 24. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized par ts or f ailure to follo w Maintenance instructions may create a risk of electric shock or injury . USE PROPER EXTENSION CORD: Mak e sure your e xtension cord is in good condition. When using an e [...]

5 tion. Without proper warm-up, hammering operation is difficult. 7. Alwa ys be sure you have a firm f ooting. Be sure no one is below when using the tool in high locations. 8. Hold the tool firmly with both hands. 9. Keep hands awa y from moving parts. 10. Do not leave the tool running. Operate the tool only when hand-held. 11 . Do not point the t[...]

6 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Switch action CA UTION: • Bef ore plugging in the tool, always chec k to see that the tool is s witched off. T o star t the tool, push the “ I (ON) ” side of the switch le v er. T o stop the to[...]

7 Indicator lamp The green pow er-ON indicator lamp lights up when the tool is plugged. The indicator lamp is lit but the tool does not start e ven if the tool is s witched on, the carbon br ushes ma y be worn out, or the electr ic circuit or the motor ma y be defectiv e. If the indicator lamp does not light up and the tool does not star t, the ON/[...]

8 Inser t the bit into the tool. T ur n the bit and push it in until it engages. If the bit cannot be pushed in, remov e the bit. Pull the chuck cov er down a couple of times. Then insert the bit again. T urn the bit and push it in until it engages. After installing, alwa ys make sure that the bit is securely held in place by trying to pull it out.[...]

9 MAINTENANCE CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore attempting to perform inspection or maintenance. Replacing carbon brushes When the resin insulating tip inside the carbon brush is e xposed to contact the commutator , it will automatically shut off the motor . When this occurs, both carbon brushes shoul[...]

10 Lubrication This tool requires no hourly or daily lubr ication because it has a grease-pac ked lubrication system. It should be relubr i- cated after e very 6 months of operation. Send the complete tool to Makita A uthor ized Service Center for this lubrication ser vice . Howe ver , if circumstances require that y ou should lubricate it by yours[...]

11 Connect the terminal and reinstall the handle. CA UTION: • Be careful not to damage the terminal or lead wires especially when wiping out the old grease or installing the handle. • Whene ver reinstalling the handle, use the two short screws f or the upper side and two long screws f or the lower side . T o maintain product SAFETY and RELIABIL[...]

Memo 12[...]

13 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut[...]

14 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade[...]

15 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy St. Fremont, CA 94538-5107 (510) 657-9881 14930 Northam St. La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Av enue Sacramento , CA 95825 (916) 482-5197 7674 Clair[...]

W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some e xamples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and o[...]