Makita 9566CV 004051 инструкция обслуживания

INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com Angle Grinder 150 mm (6”) MODEL 9566CV 004051 DOUBLE INSULA TION[...]

2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA002-2 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shoc k, fire and/or s[...]

3 5. A void body contact with gr ounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. 6. Do not expose power tools to rain or wet conditions. W ater enter ing a po wer tool will increase the risk of electric shock. 7. Do not abuse the cor d. Never use the cord t[...]

4 USE PROPER EXTENSION CORD: Mak e sure your e xtension cord is in good condition. When using an e xtension cord, be sure to use one heavy enough to carr y the current y our product will draw . An undersized cord will cause a drop in line v oltage resulting in loss of power and o verheating. T able 1 shows the correct siz e to use depending on cord[...]

5 12. Make sure cord is c lear of wheel. Do not wrap cord ar ound your arm or wrist. If control of tool is lost, cor d may become wrapped around y ou and cause personal injury . 13. Make sure the wheel is not contacting the workpiece bef ore the switch is turned on. 14. Before using the tool on an actual w ork- piece, let it run for a while. Watc h[...]

6 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Shaft lock CA UTION: • Ne ver actuate the shaft lock when the spindle is mo ving. The tool ma y be damaged. Press the shaft lock to pre vent spindle rotation when install- ing or removing accessori[...]

7 Speed adjusting dial The rotating speed can be changed by turning the speed adjusting dial to a given n umber setting from 1 to 5. Higher speed is obtained when the dial is turned in the direc- tion of number 5. And low er speed is obtained when it is turned in the direction of number 1. Ref er to the table f or the relationship between the numbe[...]

8 Installing side grip (handle) CA UTION: • Alwa ys be sure that the side grip is installed securely bef ore operation. Screw the side grip securely on the position of the tool as shown in the figure. Installing or removing abrasive cut-off wheel W ARNING: • When using an abrasiv e cut-off wheel, be sure to use only the supplied wheel guard , i[...]

9 Loosen the le ver on the wheel guard. Mount the wheel guard with the protrusion on the wheel guard band aligned with the notch on the bearing box. Then rotate the wheel guard around 180 degrees. Tighten the le ver to f asten the wheel guard. If the le ver is too tight or too loosen to f asten the wheel guard, loosen or tighten the screw to adjust[...]

10 Installing or removing abrasive disc (optional accessory) NO TE: • Use sander accessories specified in this manual. These must be purchased separately . Mount the rubber pad onto the spindle. Fit the disc on the rubber pad and screw the loc k nut onto the spindle. T o tighten the lock n ut, press the shaft lock fir mly so that the spindle cann[...]

11 Grinding and sanding operation (optional accessory) AL W A YS hold the tool fir mly with one hand on housing and the other on the side handle. T ur n the tool on and then apply the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an angle of about 15 degrees to the workpiece surf ace. During the break-in peri od [...]

12 Unplug tool and place it upside down allowing easy access to spindle. Remo ve any accessories on spindle. Thread wire wheel brush onto spindle and tighten with the wrenches. When using wire wheel brush, av oid applying too much pres- sure which causes ov er bending of wires, leading to prema- ture breakage. MAINTENANCE CA UTION: • Alwa ys be s[...]

13 002986 2 3 5 2 9 10 4 6 7 8 1 11 13 14 12 15 9566CV 1 Grip 36 2 Wheel guard 3 Inner flange 82 4 Depressed center grinding wheel / Multi-disc 5 Lock nut 5/8-45 6 Rubber pad 125 7 Abrasiv e disc 8 Sanding lock nut 5/8-48 9 W ire wheel brush 10 Wire cup brush 11 Wheel guard (For cut-off wheel) 12 Inner flange 48 13 Spacer 14 Cut-off wheel 15 Lock n[...]

Memo 14[...]

Memo 15[...]

Memo 16[...]

17 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut[...]

18 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade[...]

19 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy St. Fremont, CA 94538-5107 (510) 657-9881 14930 Northam St. La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Av enue Sacramento , CA 95825 (916) 482-5197 7674 Clair[...]

W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some e xamples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and o[...]