Makita 5093DZ инструкция обслуживания

85 mm (3-3/8”) MODEL 5093DZ 85 mm (3-3/8”) MODEL 5093DWA With High Capacity Battery Charger Blade Cutting depth No load speed Overall diameter 900 450 (RPM) length INSTRUCTION MANUAL Net weight 85 mm (3-318“) 0 - 24.5 mm 0 - 18“ 320 mm 2.0 kg (0 - 15/16”) (0 - 11/16”) (1 2.518”) 14.4 Ibs) 1,000 Battery Cartridge 1222 Voltage 12 v Mode[...]

GENERAL SAFETY RULES (For All Battery Operated Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. Do not o[...]

Tool Use and Care Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. .Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed[...]

Specific Safety Rules 1. DANGER! Keep hands away from cutting area and blade. Keep your second hand on auxiliary handle, or motor housing. If both hands are holding the saw, they cannot be cut by the blade. Keep your body positioned to either side of the saw blade, but not in line with the saw blade. KICKBACK could cause the saw to jump backwards. [...]

11. Causes and Operator Prevention of Kickback: Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the opera tor. When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back tow[...]

Do not use dull or damaged blade. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and KICKBACK. Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and KICKBACK. Use extra caution when making a &qu[...]

15. Place the wider portion of the saw base on that part of the workpiece which is solidly supported, not on the section that will fall off when the cut is made. As examples, Fig. 5 illustrates the RIGHT way to cut off the end of a board, and Fig. 6 the WRONG way. If the workpiece is short or small, clamp it down. DON'T TRY TO HOLD SHORT PLACE[...]

SYMBOLS Listed below are symbols commonly used on tools. G A AA .../ min G=l ... .... volts ................................. amperes ..... hens ................................. kilograms ............................. hours ................................. minutes ................................. seconds .......................... . alternating [...]

IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE 1. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 3. CAUTION - To reduce[...]

ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OoF) or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals with the batte[...]

Installing or removing the battery cartridge 1222 *Always switch off the tool before insertion or removal of the battery cartridge. *To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge. *To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the [...]

Charging *Your new battery cartridge is not charged. You will need to charge it before use. Use the high capacity battery charger Model DC1411 to charge the battery cartridge. *Plug the high capacity battery charger into the proper A.C. voltage source. The charg- ing light will flash in green color. *Insert the battery cartridge so that the plus an[...]

Removing or installing the saw blade CAUTIO N: Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the blade. To remove the blade, press the shaft lock so that the blade cannot revolve and use the hex wrench to loosen the bolt counter- clockwise. Then remove the bolt, outer flange and blad[...]

Adjusting the depth of cut Loosen the screw on the depth guide and move the base up or down. You can read the depth of cut by aligning the top of the notch in the depth guide with the graduations on its right side. (Note: This can be done for 0" bevel cutting only.) At the desired depth of cut, secure the base by tightening the screw Depth gui[...]

Sighting The front of the base is notched to provide two guide edges. For straight cuts, align the edge with 0" engraved on it with your cutting line on the workpiece. For 45" bevel cuts, align the edge with 45" engraved on it with your cutting line. For straight cuts I For 45" bevel cuts Cutting line Switch action CAUTION: Befo[...]

Guide rule The handy guide rule allows you to do extra-accurate straight cuts. Simply slide the guide rule up snugly against the side of the workpiece and secure it in position with the clamp screw on the front of the base. It also makes repeated cuts of uniform width possible. MAINTENANCE CAUTION: Always be sure that the tool is switched off and t[...]

Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. @ N i-Cd I To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b). Take the battery to your nearest Makita Authorized Service Center or [...]

ACCESSORIES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons The accessories or attachments should be used only in the proper and intended manner Part No, 721003-8 Has fewer teeth than cross-cut bl[...]

July-13-'98 US 85 mm (3-3/8") CORDLESS CIRCULAR SAW Model 5093D Note: The switch and other part configurations may differ from country to country. 19[...]

MODEL 5093D $:D DESCRIPTION MACHINE ~ 1 1 Name Plate 2 1 DC Motor 3 1 Motor Housing 4 3 Tapping Screw PT 4x18 5 I Compression Spring 4 6 1 Lock Off Lever 7 1 Housing Set iWith Item 111 8 1 Hex Nut M4 9 1 Battery Holder 10 1 Battery 11 1 Housing Set lW8th Item 71 12 3 Tapping Screw PT 4x18 13 1 Hex Nut M5 14 1 Tapping Screw PT 4x30 15 1 Pan Head Scr[...]