Lincoln Electric IM972 инструкция обслуживания

®  • Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com • World's Leader in Welding and Cutting Products • OUTBA CK 185 ™ OPERA T ORʼS MANUAL IM972 September, 2010 Safety Depends on You Lincoln arc welding[...]

®  FOR ENGINE powered equipment. 1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors. _________________________________________[...]

®  ii SAFETY ii ARC RA YS can burn. 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87. I standards. 4. b . Use suitable clot hing made from durable flame-resistant material to protect[...]

®  iii SAFETY iii FOR ELECTRICALL Y powered equipment. 8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment. 8.b. I ns t a ll equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturerʼs recommendations. 8.c. Ground the equipment in accordance with the U[...]

®  iv SAFETY iv PRÉCAUTIONS DE SÛRETÉ Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suiv- antes: Sûreté Pour Soudage A LʼArc 1. Protegez-vous contre la secousse électrique: a. Les circ[...]

v v Thank Y ou for selecting a QUALITY product by Lincoln Electric. We want you to take pride in operating this Lincoln Electric Company product ••• as much pride as we have in bringing this product to you! Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it handy for quick reference. Pa[...]

vi vi T ABLE OF CONTENTS Page Installation .......................................................................................................................Section A Technical Specifications ....................................................................................................... A-1 Safety Precautions. .........................[...]

A-1 INST ALLA TION OUTBACK™ 185 A-1 ®  TECHNICAL SPECIFICA TIONS - OUTBACK™ 185 (K2706-1) Make/Model Description Speed (RPM) Displacement Ignition Capacities System KOHLER 1 cylinder 3750RPM High Idle 21.96 cu. in Electric & Recoil Fuel: 6.86 gal. CS 12.75 4 cycle 1825RPM Low Idle (360 cc) Start; (24.9L) air-cooled 3400RPM Full Load OHV[...]

A-2 INST ALLA TION OUTBACK™ 185 A-2 ®  ELECTRIC SHOCK can kill. • Do not touch electrically live parts or electrode with skin or wet cloth- ing. • Insulate yourself from work and ground. • Always wear dry insulating gloves. W ARNING ENGINE EXHAUST can kill. • Use in open, well ventilated areas or vent exhaust outside. • Do not stack[...]

A-3 INST ALLA TION OUTBACK™ 185 A-3 ®  CAUTION SP ARK ARRESTER Some federal, state or local laws may require gaso- line engines to be equipped with exhaust spark arresters when they are operated in certain locations where unarrested sparks may present a fire hazard. The standard muffler included with this machine does not qualify as a spark a[...]

A-4 INST ALLA TION OUTBACK™ 185 A-4 ®  ELECTRICAL OUTPUT CONNECTIONS See Figure A.1 for the location of the current control dial, weld output terminals, ground stud, circuit break- ers, 240 and 120 volt receptacles. WELDING CABLE CONNECTIONS Cable Size and Length Be sure to use welding cables that are large enough. The correct size and length[...]

A-5 INST ALLA TION OUTBACK™ 185 A-5 ®  MACHINE GROUNDING Because this portable engine driven welder or genera- tor creates its own power, it is not necessary to con- nect its frame to an earth ground, unless the machine is connected to premises wiring (your home, shop, etc.). To prevent dangerous electric shock, other equipment to which this [...]

A-6 INST ALLA TION OUTBACK™ 185 A-6 ®  PREMISES WIRING The OUTBACK™ 185 is not recommended for premises wiring. The OUTBACK™ 185 does not have a combined 120/240 volt receptacle and cannot be connected to a premises as described in other Lincoln literature. The OUTBACK™ 185 is intended only for backup, intermittent use power. Certain el[...]

A-7 INST ALLA TION OUTBACK™ 185 A-7 ®  CAUTION Certain Electrical devices cannot be powered by the OUTBACK™ 185. See Table A.2 TABLE A.2 ELECTRICAL DEVICE USE WITH THE OUTBACK™ 185 Type Resistive Capacitive Inductive Capacitive / Inductive Common Electrical Devices Heaters, toasters, incandescent light bulbs, electric range, hot pan, skil[...]

B-1 OPERA TION OUTBACK™ 185 B-1 ®  SAFETY INSTRUCTIONS Observe additional Safety Guidelines detailed throughout this manual. W ARNING W ARNING ENGINE EXHAUST can kill. • Use in open, well ventilated areas or vent exhaust outside. • Do not stack anything on or near the engine. MOVING PARTS can injure. • Do not operate with doors open or [...]

B-2 OPERA TION B-2 OUTBACK™ 185 ®  GRAPHIC SYMBOLS USED ON THIS EQUIPMENT OR IN THIS MANUAL W ARNING / CAUTION CHOKE OIL FUEL AIR CLEANER CIRCUIT BREAKER GROUND (AUXILIAR Y POWER) WORK CLAMP ELECTRODE WELDING ARC FA S T SLOW AUT O IDLE ENGINE OFF ENGINE ST ART[...]

B-3 OPERA TION B-3 OUTBACK™ 185 ®  GENERAL DESCRIPTION The OUTBACK™ 185 is designed for commercial use welder/generator applications. As a welder it provides 185 amps of DC constant current for welding with DC stick electrodes. A single dial lets you select a full range of welding output from 50 to 185 amps. As a generator it can supply up [...]

1 2 7 8 3 or 4 6 9 10 12 11 5 1 2 7 8 3 or 4 6 9 10 12 11 5 B-4 OPERA TION B-4 OUTBACK™ 185 ®  CONTROLS AND SETTINGS All welder/generator controls are located on the Output Control Panel. Gasoline engine controls are mounted on the engine. See Figure B.1 and the figures in engine operation section. WELDER/GENERA T OR CONTROLS See Figure B.1 f[...]

B-5 OPERA TION B-5 OUTBACK™ 185 ®  ENGINE OPERA TION Starting/Shutdown Instructions Be sure all Pre-Operation Engine Service has been performed. Also, Read owners manual before starting for the first time. (See INSTALLATION section) Remove all loads connected to the AC power recepta- cles. Before starting, first open the fuel shutoff valve. A[...]

B-6 OPERA TION B-6 OUTBACK™ 185 ®  4. Insert the electrode into the electrode hold er. 5. Set the current control dial to the desired output current . 6. Start the gasoline engine. See ENGINE OPERATION in this section of the manual. 7. Strike an arc and begin welding. AFTER YOU FINISH THE WELD: 1. Stop the gasoline engine. See ENGINE OPERA- T[...]

B-7 OPERA TION B-7 OUTBACK™ 185 ®  TABLE B.2 ELECTRODE SELECTION GUIDE 120V Receptacle Operation: • Set the Output Control on the Pro-Cut 25 no higher than the 15 amp position.( Higher settings may cause circuit breaker on the OUTBACK™ 185 to trip.) • Maximum material thickness that can be cut is 1/4". 240V Receptacle Operation: ?[...]

B-8 OPERA TION B-8 OUTBACK™ 185 ®  TABLE B.3 AUXILIARY POWER APPLICATIONS Suggested Power Applications Running Watts *Start-up Watts (Continuous) (Peak) *Air Compressor - 1 HP 2,000 4,000 - 8,000 *Air Compressor - 3/4 HP 1,250 3,100 - 5,000 *Airless Sprayer - 1/3 HP 600 1,500 - 2,400 Chain Saw 1,200 Circular Saw 1,200 Coffee Maker 1,000 *Deep[...]

C-1 ACCESSORIES C-1 OUTBACK™ 185 ®  OPTIONS/ACCESSORIES The following options/accessories are available for your OUTBACK™185 from your local Lincoln Distributor: Accessory Kit (K875) – Includes the following: • Twenty feet (6.1 meters) of #6 AWG electrode cable with lug. • Fifteen feet (4.6 meters) of #6 work cable with lugs. • Work[...]

D-1 MAINTENANCE D-1 OUTBACK™ 185 ®  SAFETY PRECAUTIONS • Have qualified personnel do all maintenance and troubleshooting work. • Turn the engine off before working inside the machine. • Remove guards only when necessary to perform maintenance and replace them when the mainte- nance requiring their removal is complete. • If guards are [...]

D-2 MAINTENANCE D-2 OUTBACK™ 185 ®  To service the pre-cleaner : Remove the cover. Carefully remove the foam pre- cleaner from the filter element. 1. Wash in liquid detergent and water. 2. Squeeze dry in a clean cloth. 3. Saturate in clean engine oil. 4. Squeeze in a clean, absorbent cloth to remove all excess oil. Carefully place the pre-cle[...]

®  E-1 TROUBLESHOOTING OUTBACK™ 185 E-1 If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed. CAUTION This Troubleshooting Guide is provided to help you locate and r[...]

E-2 TROUBLESHOOTING E-2 OUTBACK™ 185 ®  Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed. CAUTION P[...]

E-3 TROUBLESHOOTING E-3 OUTBACK™ 185 ®  Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed. CAUTION P[...]

E-4 TROUBLESHOOTING E-4 OUTBACK™ 185 ®  Observe all Safety Guidelines detailed throughout this manual If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed. CAUTION P[...]

F-1 DIAGRAMS F-1 OUTBACK™ 185 ®  NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement. Give the equipment co[...]

F-2 DIMENSION PRINT F-2 OUTBACK™ 185 ®  M21768 B 6.75 29.00 31.47 NOTES : N.A. CENTER OF GRAV I TY W I TH O I L I N ENG I NE AND EMPTY FUEL TANK. N.A. 25.62 21.60 7.79 13.50 8.25 17.50 14.17 M21768 B 6.75 29.00 31.47 NOTES : N.A. CENTER OF GRAV I TY W I TH O I L I N ENG I NE AND EM PTY FUEL TANK. N.A. 25.62 21.60 7.79 13.50 8.25 17.50 14.17[...]

NOTES OUTBACK™ 185 ® [...]

W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TENÇÃO Spanish French German Portuguese Japanese Chinese Korean Arabic READ AND UNDERST AND THE MANUF ACTURERʼS INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYERʼS SAFETY PRACTICES. SE RECOMIENDA LEER Y ENTENDER LAS INSTRUCCIONES DEL F ABRICANTE P ARA EL US[...]

W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TENÇÃO Spanish French German Portuguese Japanese Chinese Korean Arabic LEIA E COMPREENDA AS INSTRUÇÕES DO F ABRICANTE P ARA ESTE EQUIP AMENTO E AS P ARTES DE USO, E SIGA AS PRÁTICAS DE SEGURANÇA DO EMPREGADOR. G Keep your head out of fumes. G Use ventilation or exhaust to remove fumes from b[...]

®  • Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com • World's Leader in Welding and Cutting Products •[...]