Light & Motion VX2000 инструкция обслуживания

Owner’ s Manual www .uwimaging.com VX2000 Bluefin[...]

3 T able of Contents Quick Start Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Bluefin VX2000 Operation - Camera Preparation . . . . . . . . . . . . . . . . . . . . . . . . . .6 Mounting the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

5 Quick Start Guide Every Light & Motion housing is pr essure tested prior to shipping. However , unseen damage may have occurred during shipping. It is str ongly recommended to test dive with only the housing prior to installing the camcorder . 1) Attach a fully charged Sony NP-750 battery to the camcorder . Install a Mini DV tape and a Memory[...]

7 Operation The Bluefin VX2000 is designed to access most camcorder featur es using a combination of infrared commands from the Smart Grips as well as mechanical interfaces on the housing. Rear Plate ON/MODE - T urns camcorder on from off state. When camcorder is in power ed state, loops between Camera - Memory and VTR modes. Program/Gain - Activat[...]

8 9 Using the Bluefin VX2000 in Camcorder mode Camcorder POWER switch should be set to MEMORY setting when installed into the housing. When the rear plate is secured to the housing, the camcorder will switch to CAM mode. Left Smart Grip (ref. fig. 9) LIGHTS - After initial power up from battery pod, cycles lights through output cycles. Press and ho[...]

Using the Bluefin VX2000 in VTR mode Left Grip (ref. fig. 1 1) F AR/- Frame Back while paused and r everse direction during playback NEAR/+ Frame Advance while paused PHOTO DIS. - Rewind during Stop and high speed reverse during Playback LIGHTS - Not used PHOTO - Captures still image to Memory Stick Right Grip (ref. fig. 12) TELE - Stop WIDE - Slow[...]

Housing Storage Store housing and T ravel Case in a dry location. 24 hours after a dive, leave the Rear Plate off the housing to allow for air circulation. Similarly , leave T ravel Case Lid about two inches open. Allow any r esidual water to evaporate from the T ravel Case prior to storing the housing. 12 13 Front Optic Installation / Removal T o [...]

Using Manual Focus The Bluefin VX2000 F AR/-, NEAR/+ and MOM.AF buttons will switch the camcorder from auto to manual focus. One technique is to toggle the F AR and NEAR buttons until the subject is in focus. Because this method is slow , we recommend the following technique. 1) While in auto focus, point the camera toward a solid object equidistan[...]

Bluefin VX2000 Lights - Getting Started Pictured below are the components of both the SunRay -X Pr o and the SunRay -X Elite lighting systems. T ake a moment to familiarize yourself with each part for later identification and use. Battery Pods Pro light heads Charger and electrical cord Light Arms Light Cable NiMH Batteries 16 6) Press the Handle C[...]

19 18 Removing Batteries 1) Rotate latch at the front of the pod counter -clockwise 1/8 turn or until it stops. 2) Pull the front cap of f the pod. 3) Pull the battery from the pod using removal strap (r ef. fig. 17 & 18). Mounting Batter y Pods Battery Pods can be mounted prior to installing batteries into pods. 1) Remove the rear plate or mon[...]

21 20 Assembly with Universal Mounts Mounting Arm to Light Heads Align top of arm with arm light head base and press FIRML Y together . Arm should snap into position. (ref. fig. 25). Removing Arm from Light Heads T o remove light head from arm, “break” the arm at the upper most joint. Applying pr essure on the Light Arm and not the Light Head ([...]

23 22 Light Operation Before you turn on the Pro lights, verify that the mode selector (flat position of black ring around red power button) is set to the P setting. Before you turn on the Elite lights, verify that the mode selector (flat position of black ring around red power button) is set to the E setting. Operation with SunRay-X Pro Lighting S[...]

25 24 Bluefin Bulkhead Installation 1) Remove the Rear Plate. 2) Locate the power switch on the circuit boar d on the inside of the Rear Plate. Switch the appropriate switch (upper or lower) to ON. This activates power to the bulkhead. (ref. fig. 29) 3) Using a flat head screwdriver or coin, remove the Port Plug (r ef. fig. 30) 4) On the inside of [...]

Bluefin Compact Monitor ID and Operation The External Monitor consists of three components • External Monitor - provides a 2.5” image of camera view • Clamp assembly - mounts monitor to back of housing • Cable - provides video signal from housing to External Monitor 1) Install monitor by first attaching clamp assembly to back of monitor . 2[...]

Diving Without a Monitor Attached If you do not use the monitor you MUST de-activate power to the bulkhead before entering the water . T o de-activate Bluefin bulkhead: 1) Remove the Rear Plate 2) Locate the on/off switch on the inside of the Rear Plate. 3) Switch appropriate bulkhead to of f position. Power On/Off with Remote Monitor On - When cam[...]

31 30 Returning Products for Care W e highly recommend a factory annual service to maintain proper operation of your Bluefin Housing. 1) Before returning your Light & Motion product for care, please call or email our service department for a RMA number . 2) Ship your product pre-paid freight with the return number printed on the outside of the [...]

905-0187-A 300 Canner y Row • Monterey , CA 93940 (831) 645-1525 • Fax (831) 375-2517 www .uwimaging.com[...]