LG Electronics LT64 инструкция обслуживания

www .lg.c om O WNER’S MANU AL LED L CD T V Please r ead this manual caref ully bef ore operating your set and r etain it f or futur e r ef erence. L T64**[...]

ENG ENGLISH 2 T ABLE OF CONTENTS 21 MAINTENANCE 21 Cleaning your TV 21 - Screen, frame, cabinet and stand 21 - Power cord 21 TROUBLESHOOTING 22 CAUTION FOR USING EZSIGN 2.0 23 SPECIFICA TIONS 26 IR CODES 27 EXTERNAL CONTROL DEVICE SETUP 27 RS-232C Setup 27 T ype of connector; D-Sub 9-Pin Male 27 RS-232C Configurations 28 Communication Parameters 28[...]

3 LICENSES / OPEN SOURCE SOFTW ARE NOTICE ENG ENGLISH LICENSES Supported licenses may differ by model. For more information about licenses, visit www .lg.com. Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. HDMI, the HDMI logo and High-Definition Multimedia Interface are [...]

4 INST ALLA TION PROCEDURE / ASSEMBLING AND PREP ARING ENG ENGLISH NOTE y Image shown may differ from your TV . y Y our TV’ s OSD (On Screen Display) may differ slightly from that shown in this manual. y The available menus and options may differ from the input source or product model that you are using. y New features may be added to this TV in [...]

5 ASSEMBLING AND PREP ARING ENG ENGLISH Remote control, Batteries (AAA) (See p.20) Owner ’ s manual Cable holder (Depending on model) (See p.14) Power cord Stand Screws 8 EA, M4 x 12 (Only 26L T64 ** ) (See p.9) Stand Screws 8 EA, M4 x 14 (Only 32/37/42/47L T64 ** ) (See p.10) Desk-mount Screw 1 EA, M4 x 20 (Only 32/37/42/47L T64**) (See p.1 1) D[...]

6 ASSEMBLING AND PREP ARING ENG ENGLISH NOTE y Antenna Isolator Installation Guide - Use this to install TV in a place where there is a voltage dif ference between TV Set and GND of antenna signal. » If there is a voltage difference between TV Set and GND of antenna signal, the antenna contact might be heated and excessive heat might cause an acci[...]

7 ASSEMBLING AND PREP ARING ENG ENGLISH Parts and buttons Button Description ∨∧ Scrolls through the saved programmes. - + Adjusts the volume level. T urns the power on or off. OPT ICA L DI GIT A L AUDI O O UT AUD IO IN RS-2 32C IN (CO NTR OL & SER VICE) RGB IN (P C) 2 1 AUD IO I N (RG B/ DV I) RS- 232 C I N (CO NT RO L & SERV ICE ) ANTE[...]

8 ASSEMBLING AND PREP ARING ENG ENGLISH y It is recommended to move the TV in the box or packing material that the TV originally came in. y Before moving or lifting the TV , disconnect the power cord and all cables. y When holding the TV , the screen should face away from you to avoid damage. y Hold the top and bottom of the TV frame rmly . Make[...]

9 ASSEMBLING AND PREP ARING ENG ENGLISH Setting up the TV Put your TV on a pedestal stand and mount the TV on a table or wall. Attaching the stand (Only 26L T64**) Front Stand Body Stand Base M4X20 T op View 1 M4 x 12 4 EA 2 3 M4 x 12 4 EA[...]

10 ASSEMBLING AND PREP ARING ENG ENGLISH (Only 32/37/42/47L T64 ** ) Front 1 Stand Body Stand Base 3 2 M4 x 14 4 EA CAUTION y When attaching the stand to the TV set, place the screen facing down on a cushioned table or at surface to protect the screen from scratches. y Make sure that the screws are inserted correctly and fastened securely . If t[...]

1 1 ASSEMBLING AND PREP ARING ENG ENGLISH Mounting on a table 1 Lift and tilt the TV into its upright position on a table. - Leave a 10 cm (minimum) space from the wall for proper ventilation. 2 Connect the power cord to a wall outlet. Securing the TV to a table (Only 32/37/42/47L T64 ** ) Fix the TV to a table to prevent from tilting forward, dama[...]

12 ASSEMBLING AND PREP ARING ENG ENGLISH Securing the TV to a wall (This feature is not available for all models.) 1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV . - If there are bolts inserted at the eye-bolts position, remove the bolts first. 2 Mount the wall brackets with the bolts to the wall. Match the locat[...]

13 ASSEMBLING AND PREP ARING ENG ENGLISH Not using the DESK-TYPE ST AND (Only 32/37/42/47L T64 **) Image shown may differ from your TV . When installing the wall-mounted unit, use the protection cover . Insert the Protection cover into the TV until clicking sound. Protection Cover CAUTION y Disconnect the power first, and then move or install the T[...]

14 ASSEMBLING AND PREP ARING ENG ENGLISH Tidying cables (Only 32/37/42/47L T64 ** ) CAUTION y Do not move the TV by holding the Cable Holder and Power Cord Holder , as the Cable holders may break, and injuries and damage to the TV may occur . (Only 26L T64 **) 1 Gather and bind the cables with the cable holder . Cable Holder 1 Install the Power Cor[...]

15 MAKING CONNECTIONS ENG ENGLISH MAKING CONNECTIONS This section on MAKING CONNECTIONS mainly uses diagrams for the 32L T64** models. Connect various external devices to the TV and switch input modes to select an external device. For more information on external device’s connection, refer to the manual provided with each device. Available extern[...]

16 MAKING CONNECTIONS ENG ENGLISH HDMI connection T ransmits the digital video and audio signals from your PC to the TV . Connect the PC and the TV with the HDMI cable as shown. Choose any HDMI input port to connect. It does not matter which port you use. NOTE y It is recommended to use the TV with the HDMI connection for the best image quality . y[...]

17 MAKING CONNECTIONS ENG ENGLISH Component connection T ransmits analog video and audio signals from an external device to the TV . Connect the external device and the TV with the component cable as shown. DVD / Blu-Ray / HD Cable Box GREEN VIDEO VIDEO AUDIO AUDIO V IDE O R A V IN A V I N V IDE O L / M O N O AU DI O R GREEN BLUE WHITE RED RED RED [...]

18 MAKING CONNECTIONS ENG ENGLISH Composit connection T ransmi ts the analogue video and audio signals from an external device to the TV . Connect the external device and the TV with the composite cable as shown. Audio connection Y ou may use an optional external audio system instead of the built-in speaker . NOTE y If you use an optional external [...]

19 MAKING CONNECTIONS ENG ENGLISH Headphone connection T ransmits the headphone signal from the TV to an external device. Connect the external device and the TV with the headphone. (*Not Provided) NOTE y AUDIO menu items are disabled when connecting a headphone. y When changing A V MODE with a headphone connected, the change is applied to video but[...]

20 REMOTE CONTROL ENG ENGLISH The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully and use the TV correctly . T o replace batteries, open the battery cover , replace batteries (1.5 V AAA) matching the and ends to the label inside the compartment, and close the battery cover . T o remove t[...]

21 MAINTENANCE / TROUBLESHOOTING ENG ENGLISH MAINTENANCE Cleaning your TV Clean your TV regularly to keep the best performance and to extend the product lifespan. CAUTION y Make sure to turn the power off and disconnect the power cord and all other cables first. y When the TV is left unattended and unused for a long time, disconnect the power cord [...]

22 CAUTION FOR USING EZSIGN 2.0 ENG ENGLISH CAUTION FOR USING EZSIGN 2.0 Only 26/32/37/42/47L T640E y Do not remove a USB drive while data is being copied. It can corrupt the data and EzSign may not work properly . y While loading a USB device or dongle, your TV may function slower than normal. y While EzSign contents is running, the movie with int[...]

23 SPECIFICA TIONS ENG ENGLISH SPECIFICA TIONS Product specifications may be changed without prior notice due to upgrade of product functions. For the power supply and power consumption, refer to the label attached to the product. MODELS 26L T64** 26L T640H-T A 26L T640E-T A Dimensions (W x H x D) With stand(mm) 626.0 x 454.0 x 192.0 Without stand([...]

24 SPECIFICA TIONS ENG ENGLISH Digital TV Analogue TV New Zealand, Singapore T elevision System DVB-T P AL /SE CAM -B /G/ D/K , P A L - I Programme Coverage UHF 21 to 69 BG : VHF/UHF 1 to 69, CA TV 01 to 47 I : VHF/UHF 1 to 69, CA TV 01 to 47 DK : VHF/UHF 1 to 69, CA TV 01 to 47 Australia T elevision System DVB-T P AL B/B Programme Coverage VHF 06 [...]

25 SPECIFICA TIONS ENG ENGLISH HDMI/DVI-DTV supported mode Resolution Horizontal Frequency (kHz) V ertical Frequency (Hz) 720x480 31.469 31.5 59.94 60 720x576 31.25 50 1280x720 37.5 44.96 45 50 59.94 60 1920x1080 33.72 33.75 28.125 26.97 27 33.716 33.75 56.25 67.43 67.5 59.94 60 50 23.97 24 29.976 30.00 50 59.94 60 Component port connecting informa[...]

26 IR CODES ENG ENGLISH Code (Hexa) Function Note 08 (POWER) Remote control Button (Power On/Off) 95 ENERGY SA VING Remote control Button 30 A V MODE Remote control Button 0B INPUT Remote control Button F0 TV/RAD Remote control Button 10-19 Number Key 0-9 Remote control Button 53 LIST Remote control Button 1A Q.VIEW Remote control Button 02 Remote [...]

27 EXTERNAL CONTROL DEVICE SETUP ENG ENGLISH EXTERNAL CONTROL DEVICE SETUP RS-232C Setup Connect the RS-232C (serial port) input jack to an external control device (such as a computer or an A/V control system) to control the product’s func- tions externally . Connect the serial port of the control device to the RS-232C jack on the product back pa[...]

28 EXTERNAL CONTROL DEVICE SETUP ENG ENGLISH Command reference list Communication Parameters y Baud rate: 9600 bps (UART) y Data length: 8 bits y Parity : None y Stop bit: 1 bit y Communication code: ASCII code y Use a crossed (reverse) cable. y * Note : During USB operations such as DivX or EMF , all commands except Power(ka) and Key(mc) are not e[...]

29 EXTERNAL CONTROL DEVICE SETUP ENG ENGLISH T ransmission / Receiving Protocol T ransmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] : First command to control the TV .(j, k, m or x) [Command 2] : Second command to control the TV . [Set ID] : Y ou can adjust the set ID to choose desired monitor ID number in option menu. Adj ust me[...]

30 EXTERNAL CONTROL DEVICE SETUP ENG ENGLISH 08. Colour (Command: k i) ► T o adjust the screen colour . Y ou can also adjust colour in the PICTURE menu. Data Min : 00 to Max : 64 * Refer to ‘Real data mapping’. See p.33. T ransmission [k][i][ ][Set ID][ ][Data][Cr] Ack [i][ ][Set ID][ ][OK/NG][Data][x] 04. V olume Mute (Command: k e) ► T o [...]

31 EXTERNAL CONTROL DEVICE SETUP ENG ENGLISH Data Min : 00 to Max : 64 * Refer to ‘Real data mapping’. See p.33. 12. Remote control lock mode (Command: k m) ► T o lock the front panel controls on the monitor and remote control. T ransmission [k][m][ ][Set ID][ ][Data][Cr] Data 00 : Lock off 01 : Lock on * If you are not using the remote contr[...]

32 EXTERNAL CONTROL DEVICE SETUP ENG ENGLISH 19. Tune Command (Command: m a) ► Select channel to following physical number . T ransmission [m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][Cr] Ack [a][ ][Set ID][ ][OK/NG][Data][x] Data Min: 00 to Max: 7DH 18. Auto Configure(Command: j u) ► T o adjust picture position and minimize image shaking au[...]

33 EXTERNAL CONTROL DEVICE SETUP ENG ENGLISH * Real data mapping 00 : S te p 0 A : St ep 1 0 ( S e t I D 1 0) F : S t ep 1 5 (S et I D 1 5 ) 10 : S te p 16 ( S e t I D 1 6) 64 : S te p 10 0 6E : St ep 1 1 0 73 : S te p 1 15 74 : S te p 1 16 CF : S t e p 1 99 FE : S t ep 2 5 4 FF : St ep 2 5 5 23. Input select (Command: x b) (Main Pictu re In put) ?[...]

25. 3D(Command: x t) (only 3D models) (Depending on model) ► T o ch a n ge 3D m od e f or T V . D a ta S t ru ct ur e D a ta 01 0 0 : 3 D O n 01 : 3 D O ff 02 : 3 D t o 2 D 03 : 2 D t o 3 D D a ta 02 0 0 : T op a nd B o tt om 01 : S id e by Si d e 02 : C he ck B oa rd 03 : F ra me S eq ue n t ia l D a ta 03 0 0 : R ig ht t o Le f t 01 : L ef t to[...]