Lanzar Lanzar Vibe VBD300 инструкция обслуживания

OWNER’S MANUAL VBD 300 PLL SYNTHESIZER STEREO RADIO WITH COMP ACT DISC PLA YER DIGIT AL[...]

2 INST ALLA TION Notes: • Choose the mounting location where the unit will not interfer e with the normal driving function of the driver . • Before finally installing the unit, connect the wiring temporarily and make sur e it is all connected up properly and the unit and the system work pr operly . • Use only the parts included with the unit [...]

1. Dashboard 2. Nut (5mm) 3. Spring washer 4. Scr ew (5 x 25mm) 5. Screw 6. Strap Be sure to use the strap to secur e the back of the unit in place. The strap can be bent by hand to the desired angle. 7. Plain washer Removing the unit 1. Frame 2. Insert fingers into the gr oove in the fr ont of frame and pull out to remove the frame. (When reattach[...]

4 HOW TO REMOVE AND INST ALL THE FRONT P ANEL (OPTIONAL) 1. Pr ess the r elease button and pull-off the fr ont panel. Keep front panel into the case. 2. T o install the front panel, insert the panel into the housing and make sur e the panel is properly installed, otherwise, abnormalities occurs on the display or some keys will not function properly[...]

ANTENNA CONNECT OR MEMORY BACK-UP FRONT Lch SPEAKER MAIN UNIT FRONT Rch SPEAKER IGNITION SWITCH (B+) POWER ANTENNA REAR Lch SPEAKER REAR Rch SPEAKER GROUND (B–) RED YELLOW BLACK CHOKE BOX BLUE + – + – + – + – Rch RED Lch WHITE (FOR RCA LINE OUT VERSION ONL Y) FRONT RCA CABLE REAR RCA CABLE (BROWN) (GREY) WHITE WHITE/BLACK GREEN GREEN/BLAC[...]

6 LOCA TION AND FUNCTION OF CONTROLS (1) ON/OFF Press POWER button (1) to turn on. Press it again to turn it off. If the power is off, press BND button (11) or MOD button (12) also can turn on the unit. (2) DISC PLA Y Gently insert a compact disc with the label side facing up into the disc slot (2). The disc is then automatically loaded into the un[...]

7 FM1 FM2 FM3 AM1/MW AM2/L W BAS TRE BAL F AD VOL (Bass) (T r eble) (Balance) (Fader) (Volume) (4) MONO/STEREO (FOR MON VERSION ONL Y) Press MON button (4) to select monaural or ster eo (Mono reception for radio stations). Y ou can sometimes improve r eception of distant stations by selecting mono operation. (4) SUB-WOOFER (FOR SUB.W . VERSION ONL [...]

(13) LIQUID CR YST AL DISPLA Y The LCD (13) can show the current state of the unit. (14 & 15) SELECT ST A TIONS Press and r elease a TUNE/SEEK/TRACK button /– (14) or +/ (15) immediately to move radio frequency number up or down on step. Press and hold a TUNE/SEEK/TRACK button /– (14) or +/ (15) for several seconds to seek the next clear st[...]

9 (23) AUTOMA TICALL Y STORING & PROGRAM SCANNING Automatically Storing Press and hold AMS button (23) for several seconds to toggle automatically storing function. It starts searching next fr equency in local mode and stores the clear station into the preset memory . If 6 ch. is not fully memorised, it would start the second searching in dista[...]

10 Remote Control Handset 8 6 2 1 3 4 5 7 14 9 13 11 12 15 10 Contr ol & Function Keys 1. POWER = Power ON/OFF Button 2. MOD = Mode Button 3. SEL = Select Button 4. EQ = Equalization Button 5. BND = Band Select Button 6. MUTE = Mute Button 7. VOL + = V olume Up Button 8. VOL – = V olume Down Button 9. TUN/SEK = T une/Seek Up Button 10. TUN/SE[...]

11 SPECIFICA TION GENERAL Po w er Supply Requirements : DC 12 V olts, Negative Ground Chassis Dimensions : 178 (W) x 155 (D) x 50 (H) Tone Controls - Bass (at 100 Hz) : +10 dB / –10 dB -T r eble (at 10 KHz) : +10 dB / –10 dB Maximum Output P ow er - Version v : 7W x 4 (ch) or 25W x 2 (ch) - Version z : 25W x 4 (ch) - Version y : 40W x 4 (ch) CD[...]

TROUBLE SHOOTING Before going thr ough the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer . Symptom Cause Solution No power . The car ignition is not on. If the power supply is properly connected to the car accessory terminal, switch the ignition key to “ACC?[...]