KitchenAid 3182048 инструкция обслуживания

HOME APPLIANCES Installation Instructions Create-a-Cooktop I D I I Part No. 3182048 Rev. E Important: IMPORTANT: Read and save these instructions. Installer: Leave Installation Instructions with the homeowner. Homeowner: Keep Installation Instructions for future reference. Save Installation Instructions for local electrical inspector’s use. Write[...]

Minimum cabinet width above one appliance: cooktops - 12” Grill - 14” IMPORTANT: Observe all governing codes and ordinances. Downdraft vent - 6” For each additional appliance combined with the first appliance, add the minimum cabinet width for that appliance. LElectric - I” min. Gas - 1’ min to backsplash or vertical wall ’ I See Note* [...]

Before vou start... Proper installation iz your responsibility. Make sure you have everything necessary for correct installation. It is the responsibility of the installer to comply with the installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the bottom of cooktops and grills and on the ri[...]

Product/cutout Dimensions Single Installations - One product per cutout Electric and Gas cooktops Electric Grill lf-1345/16” -4 WARNING: To reduce the risk of fire, electric shock and injury to persons, the downdraft vent system must be installed with either the KitchenAid Model KPED890T exterior mounted motor unit or the KitchenAid Model KPID850[...]

Combinations - When installing cooktops, grills and downdraft vents in the same cutout, use the following width dimensions: Combination 2 cooktops 3 cook-tops 4 cooktops 1 cook-top and 2 cooktops and 3 cooktops and 1 downdraft vent 1 downdraft vent 2 downdraft vents Cutout Width 23’ min. 35’ min. 47” min. 16-7/a’ min. 29” min. 47’ min. [...]

Tools/Parts Electric Cooktop and Grill Tools and materials needed for installation: Electric cooktops and grills pipejoint compound Downdraft vents l Phillips screwdriver l metal snips l wire stripper or utility knife l duct tape l caulking gun l measurmg tape/ruler l flat-blade screwdriver or 7/16” nut driver l pencil l power supply cable l sabe[...]

Electrical connection This appliance is manufactured with a frame- connected, green or bare, ground wire. Connect the appliance cable to the junction box through the U.L.-listed conduit connector. Complete electrical connection according to local codes and ordinances. Electrical Shock Hazard Turn power supply off before connecting wires. Electrical[...]

Electric Cooktop and Grill (cont.) Now start... With cooktop and/or grill in kitchen. If installing more than one appliance in the same cutout, work with one appliance at a time. Start with the appliance that will be to the left side of the cutout. Make all adjustments: then follow steps to add adjacent appliances. q 1 Remove the shipping materials[...]

Do Not overtighten screws. glass cooktop countertop El 5/16” clamping 7 bracket screw . One cooktop or grill in cutout: Rotate the mounting brackets away from the burner box. Tighten the mounting brackets to the burner box. Insert the 2-l/2” clamping screws into the mounting brackets. Use a screwdriver to tighten the screws against the undersid[...]

Downdraft Vent Electrical requirements WARNING: To reduce the risk of fire, electric shock and injury to persons, the downdraft vent system must be installed with either the KitchenAid Model KPED890T exterior mounted motor unit or the KitchenAid Model KPID850T interior mounted motor unit. These units are marked to indicate their suitability with th[...]

Venting requirements Ductwork needed for installation is not supplied. Wall cap is provided with interior mounted motor. I Fire Hazard Venting system MUST terminate to the outside. Do Not terminate the ductwork in an attic or other enclosed space. Do Not use 4-inch laundry-type wall caps. Do Not use plastic-type ductwork. Use only metal ductwork. F[...]

Downdraft Vent (cont.) Exterior mounted vent motor installation methods To install ductwork under a concrete slab, see Insert Sheet. Do not install exterior vent motor in a window well. Island location Figure 5 Interior wall location Figure 6 Roof venting Figure 7 One exterior power vent motor can be used to operate two downdraft vent systems. The [...]

Now start . n n n El 1 Place cardboard or other form of . protection on top of a flat surface where you can easily assemble the downdraft vent system. Remove downdraft blower box and motor section from cartons. Remove any shipping materials, tape and protective film from downdraft blower box and motor. Remove parts package from inside blower box op[...]

Downdraft Vent /cont.) If downdraft vent is installed next to another appliance in the same cutout, go to Step 11. If downdraft vent will be installed in a separate cutout (no other appliances in same cutout), remove the motor from the blower box. Carefully insert the blower box into the countertop cutout. Lift motor up and place on blower box. Con[...]

other brown wire to the other capacitor terminal. Replace the rubber cap over the top of the capacitor. Put the capacitor into the mounting bracket on the lower section of the wiring box. the front of the blower box under the control using the four screws removed in Step 3. If the vent is installed in the cutout, it may have to be lifted out of the[...]

Downdraft Vent (cont.) Exterior roof-mounted system requires Roof Mount Kit, Part No. 4173296. 11.1 Place cardboard or other form of protection on top of a flat surface where you can easily assemble the downdraft vent system. Remove downdraft blower box and motor sections from cartons. Remove any shipping materials, tape and protective film from do[...]

Position the downdraft vent cover so that it is aligned with light pencil marks made on the countertop in Step 6. Use screws to attach legs to cabinet floor. Check that blower box is vertical. (Adjust legs until blower box is vertical.) Tighten screws that attach the legs to the blower box. Determine the location where the exterior blower assembly [...]

Downdraft Vent (cont.) green ground Power supply wiring is not provided. ‘;r !/I lfT3ire Aconnector Thread the power supply cable through the conduit connector. Tighten the screws on the conduit connector. Disconnect power supply. Connect the two white wires together with twist- on wire connector. Connect the black wire from the power supply cab[...]

Sealed Gas Cooktop Gas supply requirements Explosion Hazard Use a new AGA approved gas supply line. Install a shut-off valve. Securely tighten all gas connections. If connected to LP, have a qualified person make sure gas pressure does not exceed water column rating specified in LP conversion kit. Examples of a qualified person include licensed hea[...]

Sealed Gas Cooktop (cont.) Electrical requirements Electrical Shock Hazard Plug into a grounded 3-prong outlet. Do not remove ground prong. Do not use an adapter. Failure to follow these instructions can result in death, fire, or electrical shock. If codes permit and a separate ground wire is used, it is recommended that a qualified electrician det[...]

To avoid scratching countertop, lift entire cooktop up from cutout when repositioning cooktop into countertop opening. 13.) I I Insert the cooktop into the countertop opening. Check that the front of the cooktop is parallel to the front edge of the countertop. Check that all required clearances are met. Use a pencil to mark a line along the rear of[...]

Sealed Gas Cooktop (cont.) Multiple cooktops and/or grill combinations: Rotate the left mounting bracket away from the burner box of the first appliance. Tighten the mounting bracket to the burner box. Insert the 2-l/2” clamping screw into the mounting bracket. Use a screwdriver to tighten the screw against the underside of the countertop. Rotate[...]

. Plug the power supply cord into-the grounded outlet. I I 115.1 t I Place burner grates over burners and caps. Install control knobs on valve stems. Electronic Ignition System - initial lighting Cooktop burners use electronic ignitors in place of standing pilots. When the cooktop control knob is turned to the “HI” position, the system creates [...]

W iring diagram (WNHT, BkK) (GEN) II L-h I I I I I / , (RED) wHT) (RED (BLK) I (BLK) - 0 - n GAS VALVE GAS VALVE FRONT REAR Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. If the cooktop, grill or downdraft vent does not oper[...]