Kenwood TK-3202L инструкция обслуживания

© B62-1971-00 (K, K2, K3, M, M2) 09 08 07 06 05 04 03 02 01 00 TK-2202L/ TK-3202L VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER INSTRUCTION MANUAL ÉMETTEUR-RÉCEPTEUR FM VHF/ ÉMETTEUR-RÉCEPTEUR FM UHF MODE D’EMPLOI TRANSCEPTOR DE FM VHF/ TRANSCEPTOR DE FM UHF MANUAL DE INSTRUCCIONES[...]

VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER TK-2202L/ TK-3202L INSTRUCTION MANUAL ENGLISH[...]

T HANK Y OU We are grateful you have chosen KENWOOD for your land mobile radio applications. We believe this easy-to-use transceiver will provide dependable communications to keep personnel operating at peak efficiency . KENWOOD transceivers incorporate the latest in advanced technology . As a result, we feel strongly that you will be pleased with [...]

i P RECAUTIONS • Do not charge the transceiver and battery pack when they are wet. • Ensure that there are no metallic items located between the transceiver and the battery pack. • Do not use options not specified by KENWOOD . • If the die-cast chassis or other transceiver part is damaged, do not touch the damaged parts. • If a headset or[...]

ii T urn the transceiver power off in the following locations: • In explosive atmospheres (inflammable gas, dust particles, metallic powders, grain powders, etc.). • While taking on fuel or while parked at gasoline service stations. • Near explosives or blasting sites. • In aircrafts. (Any use of the transceiver must follow the instructions[...]

iii One or more of the following statements may be applicable: FCC W ARNING This equipment generates or uses radio frequency energy . Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an u[...]

iv CONTENTS UNP ACKING AND CHECKING EQUIPMENT .......................... 1 S UPPLIED A CCESSORIES ................................................ 1 PREP ARA TION .......................................................... 3 B A TTER Y P ACK P RECAUTIONS ........................................... 3 C HARGING THE B A TTERY P ACK ....................[...]

1 UNP ACKING AND CHECKING EQUIPMENT Carefully unpack the transceiver . W e recommend that you identify the items listed in the following table before discarding the packing material. If any items are missing or have been damaged during shipment, file a claim with the carrier immediately . S UPPLIED A CCESSORIES Note: A type code (K, K2, K3, M, or M[...]

2 Belt clip (KBH-10) Speaker/ microphone jack cover Screw set Speaker/ microphone locking bracket Li-ion battery pack (KNB-45L) Antenna: K, M types (TK-2202L) Battery charger (KSC-35) Antenna: K, M types (TK-3202L) AC adapter (K, K2, K3 types) Antenna: K2, M2 types (TK-3202L) AC adapter (M, M2 types) Antenna: K3 type (TK-3202L)[...]

3 B A TTER Y P ACK P RECAUTIONS Do not use battery packs or battery chargers not recommended by KENWOOD . ◆ Do not recharge the battery pack if it is already fully charged. Doing so may cause the life of the battery pack to shorten or the battery pack may be damaged. ◆ After recharging the battery pack, disconnect it from the charger . If the c[...]

4 Information concerning the Li-ion battery pack: The battery pack includes flammable objects such as organic solvent. Mishandling may cause the battery to rupture producing flames or extreme heat, deteriorate, or cause other forms of damage to the battery . Please observe the following prohibitive matters. • Do not disassemble or reconstruct bat[...]

5 • Use only the specified charger and observe charging requirements! If the battery is charged in unspecified conditions (under high temperature over the regulated value, excessive high voltage or current over regulated value, or with a remodeled charger), it may overcharge or an abnormal chemical reaction may occur . The battery may generate he[...]

6 • Do not charge the battery for longer than the specified time! If the battery pack has not finished charging even after the regulated time has passed, stop it. The battery may generate heat or smoke, rupture, or burst into flame. • Do not place the battery pack into a microwave or high pressure container! The battery may generate heat or smo[...]

7 ■ Using the Li-ion Battery Pack • Charge the battery pack before using it. •T o keep the battery discharge at a minimum, remove the battery pack from the equipment when it is not in use. Store the battery pack in a cool and dry location. • When storing the battery pack for a long period: 1 Remove the battery pack from the equipment. 2 Dis[...]

8 1 Plug the AC adapter cable into the jack located on the rear of the charger . 2 Plug the AC adapter into an AC outlet. 3 Slide a battery pack or a transceiver equipped with a battery pack into the charging slot of the charger . • Make sure the metal contacts of the battery pack mate securely with the charger terminals. • The indicator lights[...]

9 I NST ALLING / R EMOVING THE B A TTERY P ACK ◆ Do not short the battery terminals or dispose of the battery by fire. ◆ Never attempt to remove the casing from the battery pack. 1 Align the battery pack with the back of the transceiver , then press the battery pack and transceiver firmly together until the release latch on the base of the tran[...]

10 I NST ALLING THE A NTENNA Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure. Note: The antenna is neither a handle, a key ring retainer , nor a speaker/ microphone attachment point. Using the antenna in these ways may damage the antenna and degrade your tra[...]

11 If you are not using a speaker/ microphone, install the cover over the speaker/ microphone jacks using the supplied 3 x 6 mm screw . Note: T o keep the transceiver water resistant, you must cover the speaker/ microphone jacks with the supplied cover . I NST ALLING THE C OVER OVER THE S PEAKER / M ICROPHONE J ACKS I NST ALLING THE O PTIONAL S PEA[...]

12 GETTING ACQUAINTED Speaker Speaker/ microphone jacks Microphone Antenna PTT (Push-T o- T alk) switch Press, then speak into the microphone to call a station. Release to receive. Side 1 key Press to activate its programmable function (page 13). LED indicator Lights red while transmitting. Lights green while receiving a signal. Flashes red when th[...]

13 PROGRAMMABLE AUXILIAR Y FUNCTIONS Y our dealer can program each of the Side 1 and Side 2 keys with one of the following auxiliary functions. Refer to their descriptions, starting on page 15. • Autodial • Key Lock • Key Lock with Backup • Monitor • Monitor Momentary • None (No function) (default setting for Side 1 key) • Scan • Sc[...]

14 BASIC OPERA TIONS 1 T urn the Power switch/ V olume control clockwise to switch the transceiver power ON. •A beep sounds if enabled by your dealer . 2 Press the key programmed with the Monitor or Squelch Off function to hear background noise, then rotate the Power switch/ V olume control to adjust the volume. 3 Rotate the Channel selector to s[...]

15 ADV ANCED OPERA TIONS The following functions are programmable by your dealer , as described on page 13. A UTODIAL Press and hold the PTT switch, then press the key programmed as Autodial to transmit the stored DTMF code. Release the Autodial key , then speak into the microphone while still pressing the PTT switch to call the other party . T ALK[...]

16 K EY L OCK Press and hold the key programmed as Key Lock for 1 second to lock/ unlock the transceiver keys. The following keys/ functions can still be used when Key Lock is active: Autodial, Key Lock, Monitor , Monitor Momentary , PTT , Squelch Off, Squelch Of f Momentary , and V olume. If the key is programmed as Key Lock with Backup , when the[...]

17 S CAN Scan is useful for monitoring signals on the transceiver channels. When scanning, the transceiver checks for a signal on each channel and only stops if a signal is present. The transceiver will remain on a busy channel until the signal is no longer present. Y our dealer programs the delay time between signal drop-out and Scan resumption. I[...]

18 ■ T emporar y Delete If a key is programmed with the T emporary Delete or Scan + T emporary Delete function, you can temporarily remove specific channels from the scanning sequence during Scan. When Scan stops at a channel, you can remove that channel from the scanning sequence by pressing and holding the key programmed as T emporary Delete or[...]

19 S CRAMBLER Scrambler allows you to hold a conversation in complete privacy . When activated, any other party listening in on your channel will be unable to understand your conversation. The transceiver scrambles your voice so that anybody listening to your conversation will not be able to understand what you are saying. In order for members of y[...]

20 VOICE OPERA TED TRANSMISSION (VOX) VOX operation allows you to transmit hands-free. This feature must first be activated by your dealer , and can only be used if you are using a supported headset. When operating VOX, you must set a VOX Gain level. This setting allows the transceiver to recognize sound levels. If the microphone is too sensitive, [...]

21 4 Press the Side 1 key to increase the VOX Gain level and the Side 2 key to decrease the level. • The VOX Gain can be adjusted from levels 1 to 10 and OFF . • The transceiver announces the VOX Gain level as you adjust it. If OFF is selected, a beep sounds. 5 Press the PTT switch to save the setting. •A beep will sound. • The transceiver [...]

22 BACKGROUND OPERA TIONS T IME - OUT T IMER (TOT) T he purpose of the T ime-out Timer is to prevent any caller from using a channel for an extended period of time. If you continuously transmit for a period of time that exceeds the programmed time set by your dealer (default is 1 minute), the transceiver will stop transmitting and an alert tone wil[...]

23 L OW B A TTER Y W ARNING Low Battery W arning alerts you when the battery needs to be recharged or replaced. While operating the transceiver , if the battery power becomes low , an alert tone will sound every 30 seconds and the LED indicator will blink red. Replace or recharge the battery pack. C HANNEL A NNUNCIA TION When changing the channel u[...]

24 S TUN When the transceiver receives a call containing a stun code, either transmit mode will be disabled, or both receive mode and transmit mode will be disabled. (This function is used when a transceiver is stolen or lost, for example.) Stun is cancelled when the transceiver receives a call with a stun reset code. D UAL -T ONE M UL TI -F REQUEN[...]

25 FleetSync O PERA TION FleetSync is a protocol owned by KENWOOD Corporation and is enabled or disabled by your dealer . This function opens the squelch only when the transceiver receives the Fleet code and ID code programmed in your transceiver . Calls that do not contain the correct codes will not be heard. ■ Receiving When you receive a signa[...]