Kenmore 31130 инструкция обслуживания

Models 31130 (30” wide - Stainless) 31133 (36” wide - Stainless) Range Hood Use & Care Guide Installation Manual ENGLISH 09030 rev. A SEARS CANADA INC., Toronto, Ontario M5B 2B8 www.sears.ca HB0108[...]

2 W ARNING T O REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJUR Y T O PERSONS, OBSER VE THE FOLLO WING: 1 . Use this unit only in the manner intended by the manufacturer. I f you have questions, contact the manufacturer at the address listed in the warranty. 2. Before servicing or cleaning unit, switch power off at service panel and lock the servi[...]

3 OPERA TION OPERA TION W arranty Safety Cleaning Operation Installation Service Parts Always turn ON your hood before you begin cooking in order to establish an air fl ow in the kitchen. Let the blower run for a few minutes to clear the air after you turn off the range. This will help keep the whole kitchen cleaner and brighter. 1. Blower Delay s[...]

4 P AR TS INCLUDED WITH HOOD T OOLS NEEDED FOR HOOD INST ALLA TION Aluminum grease fi lters (2 per hood) P ar ts Bag including: 5 no. 8 x 1½” countersunk screws 8 no. 8 x 3/4” screws 6 no. 8 x 3/8” screws 6 Drywall anchors 3 Washers Screwdriver (Robertson or Phillips) P encil T ape Measure Drill Sabre Saw K eyhole Saw -or- Duct T ape Wire S[...]

5 HL0142 RANGE HOOD SYSTEM W all & Roof Caps Broan Model 643 8” Round Wall Cap Broan Model 634 or 644 Roof Cap 8” Round Adjustable Elbow 8” Round Standard Duct 31130 or 31133 Range Hood Elbow Ductwork W arranty Safety Cleaning Operation Service Parts Installation Broan Model 639 3¼” x 10” Standard Wall Cap Upper Decorative Flue Lower[...]

6 EQUIV ALENT DUCT LENGTH CHART HR0049 HR0048 HR0047 Straight Duct 8-in. round x 2-ft. long Equivalent length 2 ft. Broan Model 643 8-in. Round Wall Cap Equivalent length 30 ft. (15-ft. w/o damper) Broan Model 634 or 644 8-in. Round Roof Cap Equivalent length 30 ft. (7-ft. w/o damper) Kenmore range hoods are designed to perform ef fi ciently when [...]

7 1. Plan where and how the ductwork will be installed. Install proper-sized ductwork, transition(s), elbow(s), and roof or wall cap. For best results, use a minimum number of transition and elbows. 2. The minimum hood distance above cooktop m ust not be less than 24’ ’. A maximum of 30’ ’ above cooktop is highly recommended for best captur[...]

8 W ARNING: Impr oper grounding can result in a risk of electric shoc k. Consult a qualifi ed electrician if the grounding instructions are not completel y understood, or if doubt exists as to whether the appliance is properl y grounded. Do not use an extension cor d. If the power supply cor d is too shor t, have a qualifi ed electrician install [...]

9 2. Choose the opening: HO0142 V ERTICAL DISCHARGE : Using a Robertson or a Phillips no. 2 screwdriver, remove the 4 top metal plate retaining screws in order to clear the vertical discharge opening (see illustration beside). Discard the metal plate and its screws. H ORIZONT AL DISCHARGE : In order to ease a retro fi t installation, the horizonta[...]

10 PREP ARE THE HOOD 4. Using a 5/16” socket, or a Robertson or a Phillips no. 2 screwdriver, remove all blower mounting screws from the inner top of the hood. Set aside the blower and its screws. HD0385 HD0386 HJ0040 1 2 5. According to your needs, the adapter/damper can be installed to the higer or lower back discharge using the upper screw hol[...]

11 INST ALL THE HOOD 1. Construct wood wall framing that is fl ush with surface of wall studs. Wood wall framing must be at least 1/2” thick and 3” high. Ensure to assemble wood wall framing to wall studs for a solid installation. Ensure the height of the framing will allow the mounting bracket to be secured to the framing within the dimension[...]

12 V ERTICAL DISCHARGE ONL Y : 6. Mount the 8” round adapter/damper (included in a separate box) to the hood using 4 no. 8 x 3/8” sheet metal screws (included). FINALIZE THE INST ALLA TION 1. Remove protective plastic film covering the lower flue only. Peel off both corners at the top of the upper fl ue. Position the lower fl ue rear notches [...]

13 INST ALLING GREASE FIL TERS Rest rear fi lters edge on fi lter springs ( A ) in the range hood. Using metal latch tab, tilt up the fi lters into position. Make sure fi lter tabs ( B ) are securely engaged in range hood front edge after installation. HD0393 A B HO0140 U PPER FLUE MOUNTING BRA CKET F RONT VIEW U PPER FLUE 3. Slide up the upper[...]

SER VICE P ARTS K EY NO .P ART NO .D ESCRIPTION Q TY . ( HOOD WIDTH ) 30” 36” 1 18504 U PPER FLUE MOUNTING BRACKET 11 2 18494 U PPER DECORATIVE FLUE 11 3 18496 L OWER DECORATIVE FLUE 11 4 18515 C OVER PLATE FOR 8” ROUND TOP EXHAUST 11 5 18522 E LECTRONIC CONTROL MODULE ( INCLUDING O VERLAY , ITEM 6) 11 6 07322 O VERLAY 11 7 05917 S OCKET (GU1[...]