Jonsered GT2123 инструкция обслуживания

Oper ator ′ s manual Please read the oper ator’ s manual carefully and make sure y ou understand the instructions before using the machine .[...]

2 – English KEY T O SYMBOLS Symbols W ARNING! A clearing saw , brushcutter or trimmer can be dangerous if used incorrectly or carelessly , and can cause serious or fatal injury to the operator or others. It is extremely impor tant that you read and understand the contents of this operator’ s manual. Please read the operator’ s manual carefull[...]

English – 3 CONTENTS Contents Note the f ollowing bef ore starting: Please read the oper ator’ s manual carefully . KEY T O SYMBOLS Symbols ....................................................................... 2 CONTENTS Contents ...................................................................... 3 Note the f ollowing bef ore star ting: ..[...]

4 – English INTR ODUCTION Dear Customer , Cong ratulations on y our choice to buy a Jonsered product! W e are convinced that you will appreciate with g reat satisfaction the quality and perf ormance of our product for a v er y long time to come. The purchase of one of our products giv es you access to prof essional help with repairs and service w[...]

English – 5 WHA T IS WHA T? What is what on the grass trimmer? 17 19 16 18 1 2 3 5 4 14 15 10 6 11 12 13 8 9 7 1 T rimmer head 2 Cord cutter 3 Cutting attachment guard 4 Shaft 5 Loop handle 6 Throttle control 7 Stop s witch 8 Star ter handle 9 Fuel tank 10 Choke control 11 Air purge 12 Air filter cov er 13 Clutch cov er 14 Cylinder cov er 15 Spa[...]

6 – English GENERAL SAFETY PRECA UTIONS Impor tant P ersonal pr otective equipment HEARING PR O TECTION W ear hear ing protection that provides adequate noise reduction. EYE PRO TECTION Alwa ys wear approv ed ey e protection. If y ou use a visor then you m ust also wear approv ed protective goggles . Approv ed protective goggles m ust comply with[...]

English – 7 GENERAL SAFETY PRECA UTIONS Mac hine ′ s safety equipment This section descr ibes the machine ′ s saf ety equipment, its pur pose, and ho w checks and maintenance should be carried out to ensure that it operates correctly . See the ”What is what?” section to locate where this equipment is positioned on your machine . The lif e[...]

8 – English GENERAL SAFETY PRECA UTIONS Cutting equipment This section describes how to choose and maintain your cutting equipment in order to: • Reduce the risk of blade thrust. • Obtain maximum cutting perf or mance. • Extend the lif e of cutting equipment. T rimmer head • Only use the recommended trimmer heads and tr immer cords. These[...]

English – 9 ASSEMBL Y Fitting the main bod y Connect the engine (A) to the tube (B) with f our screws (C). Connecting thr ottle cable and stop switc h wires 1 Fit the plastic tube (B) around the throttle cable and stop s witch wires as shown. 2 Inser t the throttle cable through the cab le adjuster sleev e on the carburettor br acket. Make sure t[...]

10 – English ASSEMBL Y Assembling the cutting equipment Fitting the trimmer guar d and trimmer head • Attach the cord cutter (A) to the trimmer guard using two M5x16 screws , locking washers and n uts as shown. • Fit the guard (B) to the gear housing (C) using the suppor t plate (D) and two scre ws. • T ur n the output shaft until one of th[...]

English – 11 FUEL HANDLING Fuel safety Ne ver star t the machine: 1 If you ha ve spilt fuel on it. Wipe off the spillage and allo w remaining fuel to e vaporate . 2 If you ha ve spilt fuel on y ourself or your clothes , change your clothes . W ash any part of your body that has come in contact with fuel. Use soap and w ater . 3 If the machine is [...]

12 – English FUEL HANDLING Mixing • Alwa ys mix the petrol and oil in a clean container intended f or fuel. • Alwa ys star t by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol. • Mix (shake) the fuel mixture thoroughly bef ore filling the[...]

English – 13 ST AR TING AND ST OPPING Chec k before starting • Check that the trimmer head and trimmer guard are not damaged or crac ked. Replace the trimmer head or trimmer guard if they hav e been e xposed to impact or are crac ked. • Ne ver use the machine without a guard nor with a def ective guard. • All cov ers must be correctly fitt[...]

14 – English W ORKING TECHNIQ UES General w orking instructions Basic safety rules 1 Look around you: • T o ensure that people, animals or other things cannot aff ect your control of the machine. • T o ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects that are thrown out b y the cutting a[...]

English – 15 W ORKING TECHNIQ UES Grass trimming with a trimmer head T rimming • Hold the trimmer head just above the g round at an angle. It is the end of the cord that does the work. Let the cord work at its own pace. Nev er press the cord into the area to be cut. • The cord can easily remov e grass and weeds up against walls , fences , tre[...]

16 – English MAINTENANCE Carb urettor Y our Jonsered product has been designed and manuf actured to specifications that reduce harmful exhaust fumes. The engine will be run in after it has used 8-10 tanks of fuel. T o ensure that the engine runs at peak performance and produces as little harmful exhaust fumes as possible after the running-in per[...]

English – 17 MAINTENANCE Cooling system T o keep the working temperature as low as possib le the machine is equipped with a cooling system. The cooling system consists of: 1 Cooling fins on the cylinder . 2 Cylinder cov er (directs cold air ov er the cylinder). Clean the cooling system with a brush once a week, more often in demanding conditions[...]

18 – English MAINTENANCE Maintenance sc hedule The f ollowing is a list of the maintenance that must be perf or med on the machine. Most of the items are descr ibed in the Maintenance section. The user m ust only carr y out the maintenance and ser vice work described in this Operator’ s Manual. More e xtensive work must be carried out by an aut[...]

English – 19 TECHNICAL D A T A T echnical data Note 1: Noise emissions in the environment measured as sound po wer (L W A ) in conf ormity with EC directive 2000/14/EC . Repor ted sound power le v el for the machine has been measured with the original cutting attachment that giv es the highest lev el. The diff erence between guaranteed and measur[...]

20 – English TECHNICAL D A T A EC-dec laration of conformity (Applies to Eur ope onl y) W e, Husqv arna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare that the gr ass trimmers Jonsered GT2123 with serial numbers dating from 2009 onwards (the y ear is clear ly stated on the rating plate , follo wed by the serial number), comply with [...]

[...]

[...]

[...]

´®z+UHT¶6_¨ 2010-02-26 ´®z+UHT¶6_¨ 1153405-26 Original instructions[...]