Jet JML-1014I инструкция обслуживания

Operating Instructions and Parts Manual Mini Lathe Models JML - 1014 I and JWL - 1220 WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No. M - 708376 Ph.: 800 - 274 - 6848 Revision A 9/06 www.wmhtoolgroup.com Copyright © WMH Tool Group[...]

2 WARRANTY AND SERVICE WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these WMH Tool Gro up Authorized Service Centers can authorize warranty repair, assist you in obtainin[...]

3 Table of Contents Table of Contents ............................................................................................................................... 3 Warning ............................................................................................................................................. 4 Specifications ...............[...]

4 Warning For your own safety, read this instruction manual before operating the lathe. Wear eye protection. Do not wear gloves, necktie, or loose clothing. Tighten all locks before operating. Rotate the workpiece by hand before applying power. Rough out the workpiece before in stalling on the faceplate. Do not mount a split workpiece or one contai[...]

5 • Give your work undivided attention. Looking around, carrying on a conversation and “horse - play” are careless acts that can result in serious injury. • Some dust created by power sanding, sawing, grinding, drilling and other construction activities contain chemicals known to cause cancer, birth defects or other reproductive harm. Some [...]

6 Specifications Model Number .......................................................... JML - 1 014 I ............................................. JW L - 1220 Stock Number .............................................................. 708375 ................................................. 708376 Swing Over Bed (in.) ............................[...]

7 Electrical Requirements In the event of a malfunction or breakdown, grou nding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment - grounding conductor and a grounding plug. The plug must be plugged into a matching outlet t hat is properly [...]

8 Unpac king 1. Remove contents from the shipping box. 2. Inspect contents for shipping damage and report damage, if any, to your distributor. 3. Be sure to keep the box and packing material should you need to pack the lathe for moving. 4. Do not clean the lathe with anything other than a damp cloth or a mild solvent. Use of heavy solvents, paint t[...]

9 Operations Tailstock Movement Tailstock Han dwheel (A, Figure 2) – Turn clockwise to move tailstock spindle forward. Turn counterclockwise to retract tailstock spindle. Tailstock Spindle Lock (B, Figure 2) – Locks tailstock spindle. Release to adjust with handwheel. Tailstock Lock (C, Figure 2) – Lo cks tailstock in position on the bed. Rel[...]

10 Face Plate (Figure 6) – Screws on to the headstock and is used in face plate turning operations. Mount your workpiece onto the faceplate with brass screws (not provided). Make sure the screws are not so long that they will enter the area of the workp iece where the material is to be removed. To remove the face plate from the spindle, place the[...]

11 4. Move the belt (E, Figure 9) to the desired pulley groo ve according to the speed chart found on the inside of the headstock access door. Be sure the belt is aligned with spindle pulley and motor pulley. 5. Tension the belt by pushing down on the motor plate handle (D, Figure 11) and re - tighten lock handle (C, Fig ure 11) Belt Replacement 1.[...]

12 Index Pin The index feature allows you to cut evenly spaced features in a workpiece while keeping the Lathe headstock spindle locked; for example, when cutting flutes on a spindle blank with a router, while the spind le blank is secured within the Lathe centers. There are 24 index positions on the lathe. 1. To use the index pin (Figure 13), scre[...]

13 JML - 1014 I Mini Lathe[...]

14 Parts List for JML - 1014 I Mini Lathe Index No. Part No. Description Size Qty 1 .............. JML 1014 - 1 01 .......... Headstock .......................................................................................... 1 2 .............. JML - 2 ...................... Faceplate ......................................................... 3” [...]

15 58 ............ JML - 58 .................... Eccentric Locking Rod ........................................................................ 1 59 ............ JML - 59A .................. Lock Handle Assembly, Tailstock ......................................................... 1 60 ............ JML - 60W ................. White Tailstock .......[...]

16 JWL - 1220 Lathe[...]

17 Parts List for JWL - 122 0 Lathe Index No. Part No. Description Size Qty 1 .............. J W L 1220 - 1 01 .......... Headstock .......................................................................................... 1 2 .............. JML - 2 ...................... Faceplate ......................................................... 3” ....[...]

18 55 ............ JML - 55 .................... Tailstock Spindle ................................................................................ 1 56 ............ JML - 56 .................... Leadscrew ......................................................................................... 1 57 ............ JML - 57 .................... E - Ri[...]

19 Electrical Connections for JWL - 1220[...]

20 WMH Tool G roup 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800 - 274 - 6848 www.wmhtoolgroup.com[...]