Impex WM-348 инструкция обслуживания

POWERHOUSE WM-348 BENCH IMPEX INC. 14777 Don Julian Rd. , City of Industry , CA 91746 Tel: (800) 999-8899 Fax (626) 961-9966 w w w .impex-fitness.com info@impex-fitness.com NOTE: Please read all instructions carefully before using this pr oduct Table of Content Safety Notice Hardw a re Identifier A ssembly Instruction Exploded Diagram Parts List Wa[...]

TA BLE OF CONTENT BEFORE YOU BEGIN...............................................................................................1 IMPORTANT SAFETY NOTICE................................................................................2 HARDW ARE IDENT IFIER.........................................................................................3 AS[...]

IM PORTA NT SA FETY NOTICE PRECA UTIONS This exerci se machine is built for optimum safety. H owever , certain precautions appl y whenev er you oper ate a piece of exercise eq uipment. Be sure to read the entir e manual before you assemble or operate your machi ne. In particular, note the follow ing safety precautions: 1. Keep children and pets awa[...]

3[...]

ASSEMBLY INSTRUCTION Tools required assembling the machine: Two Adjustable Wrenches and Allen Wrenches STEP 1 (SEE Diagram 1) A.) Connect the tw o Rear Upri ght Beams (#1) by a Cross Brace (#59) in the Mid-span. Secure them wi th two M10 x 2 3/8” Hex Bolts (#2), four ∅ ¾” W ashers (#3), one Bracket (#7), and tw o M10 Airc raft Nuts (#4) on e[...]

A.) Connect the Front Stabilizer (#42) to the Main Seat Support (#52) and secure them w ith two M 10 x ¾” H ex Bolts (#46), four ∅ ¾ ” W a shers (#3), and two M10 Ai rcraft Nuts (#4). DO NOT tighten the nuts and bol ts yet. B.) Connect the Mai n Seat Support (#52) to the open bracket on the Cr oss Brace (#59). Secure the rear hol e on the b[...]

A.) Attach a ∅ ¾” W a sher (#3) onto a M10 x 6 ¼ ” Hex Bol t (#54). Insert the Bolt through the Butterfly ( #17). Place a M10 Reg ular Nut (#57) onto the Bol t. Then insert the Bolt through the hol e on the Rear Uprig ht Beam (#1). Secure the Bol t with a Lock Knob (#8) behind the Upri ght Beam. Repeat the same step to install the other But[...]

A.) Attach the hole-si de of the Backrest Supports (#60) onto both ends of the Pivot on the Main Seat Support ( #52). The other side rest against the Backr est Adjustment Bar (#10). B.) Place the Backrest Boar d (#18) onto the Backrest Supports (#60) . Secure it wi th four M6 x 1 3/8” Hex Bolts ( #50) and ∅ ½” W ashers (#51). C.) Place Seat [...]

A.) Attach the ball end of the Cable to the Pul ley (#28) . Place the Pulley in the open slot on the Lat Bar Frame (#31) . Secure it wi th one M10 x 2 1/8” H ex Bolt (#32) , two Bushing s (#29), tw o ∅ ¾” W ashers (#3), and one M10 Air craft Nut (#4). B.) Slide the W eight Hol der (#33) onto the Lat Bar Fr ame from the bottom. Connect the Ca[...]

A.) To store the bench in a v ertical posit ion, remove the Arm C url and the Lat Bar Frame from the bench and place them onto the storage posts on the R ear Uprig ht Beams. B.) Pull out the 3” Lock Pin (#58) on the Main Seat Suppor t to fold up the bench. Make sure to re-inser t the Lock Pin on the bracket to secure the v ertical position. DIA G[...]

10 PARTS LIST[...]

KEY NO. DESCRIPTION QUA NTITY 1 Rear Upright B eam 2 2 M10 x 2 3/8” Hex Bolt 5 3 ∅ ∅ ∅ ∅ ¾” Washer 20 4 M10 Aircr aft Nut 10 5 1 5/8” x 3 1/8” Square End Cap 6 6 1 ¼” Square End Cap 2 7 Bracket 2 8 Lock Knob 2 9 ∅ ∅ ∅ ∅ 1” Round End Cap 11 10 Backrest A djustment Bar 1 11 Bar Catch Panel 2 12 ∅ ∅ ∅ ∅ ¾” Bar [...]

IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IM PEX") w arrants this product to be free from defects in wo rkmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This w arranty extends only to the original purchaser. IM PEX's obligation under this Warranty is lim[...]