Impex MWB-9000 инструкция обслуживания

NOTE: Please read all i nstructions caref ully befor e using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruc tion Parts L ist Warranty Ordering Parts Model MWB-9000 Retain This Manual for Reference 06-21-05 OWNER'S MANUAL MARCY SMITH MACHINE MWB-9000 IMPEX INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 [...]

TA BLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 SMITH MACHINE HARDW ARE PACK….......…............................................. 3 SMITH MACHINE ASSEMBLY INSTRUCTIONS......[...]

IMPORTANT SAFETY NOTICE PRECA UTIONS This exerci se machine is bui lt for optimum safety. How ever , certain precauti ons apply whenev er you operate a piece of exer cise equi pment. Be sure to read the entir e manual before you assembl e or operate y our machine. In particular , note the followi ng safety precautions: 1. Keep children and pets awa[...]

SMITH MA CHINE HA RDEWA RE PA CK 3[...]

SMITH MA CHINE HA RDEWA RE PA CK 4[...]

SMITH MA CHINE HA RDEWA RE PA CK 5[...]

SMITH MA CHINE A SSEMBLY INSTRUCTION Tools Required A ssembling the Machine: Tw o Adj ustable Wrenches and A llen Wrenches. NOTE: It is strongly recommended tw o or more people assembling this machine to av oid possible injury . STEP 1 (See Diagram 1) A.) Connect the Left & Right Base Fr ame (#1 & 2) by a Cross Brace ( #3) in the mid- span.[...]

STEP 2 (See Diagram 2) A.) Attach a Fr ont Vertical Frame (#6) to the R ight Base Frame ( #2). Secure it w ith two M 10 x 2 ¾” Carri age Bolts ( #77), Ø ¾” W ashers (#87), and M10 Ai rcraft Nuts (#88). Do not tig hten the Nuts and Bolts yet. B.) R epeat Procedure A abov e to install the other side. C.) C onnect the two Fr ont Vertical Frames[...]

DIAGRAM2 8[...]

STEP 3 (See Diagram 3) A.) Attach the R ear Vertic al Frame (#14) to the Rear Base Frame ( #5). Secure it with tw o M10 x 2 ½ ” Allen Bol ts (#69), four Ø ¾” W ashers (#87), and two M10 Ai rcraft Nuts (#88). Sli de the Sliding W eight Post (#13) onto the Rear Ver tical Frame (#14). B.) Pl ace the Lat Bar Frame Bracket ( #15) onto the Rear &a[...]

STEP 4 (See Diagram 4) A.) Attach the Left & Rig ht Lat Bar Frames (#16 & #17) to the Upper Fr ame (#10). Ali gn the holes and secure each Lat Bar Fr ame to Upper Frame w ith one M10 x 5” Al len Bolt (#67) , two Ø ¾ ” W ashers (#87), and one M10 Airc raft Nut (#88). Do not ti ghten the Nut and Bol t yet. B.) Attach the Left & Rig [...]

STEP 5 (See Diagram 5) A.) Attach the Butter fly Base (#23) to the front of Middle Vertic al Frame (#4) . Attach the Butterfly Pull ey Bracket ( #24) to the back of the Frame. Secure them w ith tw o M10 x 2 ¾” Car riag e Bolts (#77), Ø ¾ ” W ashers (#87), and M10 Airc raft Nuts (#88). B.) Sl ide the Left Butterfly (#26) onto the piv ot on th[...]

CABLE LOOP DIAGRAM 12[...]

STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Inser t the 242” Upper Cable (#35) through the sw ivel pulley bracket pre-installed i n the top front of the Right Lat Bar Frame ( #17). B.) Instal l a Ball Stopper (#86) onto the end of the Cable. Attach a U -shaped Connector ( #91) to the end of the Cable. C.) Attach a Shor t Chain (#40) in be[...]

DIAGRAM 6 14[...]

STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach one end of the 76” Butter fly Cabl e (#36) to the cli p on the Left Butterfly (#26). Draw the Cable to the Butterfly Base Bracket (#24) . B.) Attach a Pul ley ( #45) to the Bracket. Secure it wi th one M10 x 1 ¾” All en Bolt (#71), one L-shaped Bracket (#25) , two Ø ¾ ” W ashers (#[...]

STEP 8 (See Diagram 8 & Cable Loop Diagram) A.) Attach one end of the 140” H igh- Low Cabl e (#38) to the br acket on the Sliding W eight Post (#13). Secure i t wi th one M10 x 1 3/8” Allen Bolt ( #72), two Ø ¾” W ashers (#87), and one M10 Aircr a f t Nut (#88). B.) D raw the Cable upw ard to the open bracket underneath the Lat Bar Fram[...]

STEP 9 (See Diagram 9 & Cable Loop Diagram) A.) Attach the 68” Lower Cable ( #37) to the opening on the bottom of Middle Verti cal Frame (#4). Attach a Pul ley to the openi ng. Secure i t wi th one M10 x 2 ½ ” Allen Bol t (#69), tw o Long Pulley Bushing s (#48), and one M10 Aircr aft Nut (#88). B.) D raw the Cable underneath the Pul ley to[...]

18[...]

SMI TH M ACHINE PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Left Bas e Fram e 1 51 2” x 1 ¾” Sleeve 2 2 Right Base Fram e 1 52 1” End Cap 2 3 Cross Brace 1 53 Ø 1” Con-s haped End Cap 8 4 Middle Vertical F ram e 1 54 6” x 2” Rubber Bum per 1 5 Rear Base Fr am e 1 55 Ø 3” Rubber Bum per 4 6 Front Vertic al Fram e 2 56 Ø 1 ½” Rubber [...]

MULTI-PURPOSE BENCH HA RDWA RE PA CK 20[...]

MULTI-PURPOSE BENCH A SSEMBLY INSTRUCTION Tools Required A ssembling the Machine: Tw o Adj ustable Wrenches and A llen Wrenches. NOTE: It is strongly recommended this machine be assembled by tw o or more people to avoid possible inj ury. STEP 1 (See Diagram 1) A.) Attach the Main Frame (#1) to the Front & Rear Stabilizers (#2 & 3). Secure e[...]

STEP 2 (See Diagram 2) A.) Attach four Bushi ngs (#21) to a Seat Support Frame (#6) . B.) Attach a Backr est Support (#7) to the rear of the Seat Support Frame (#6) . Alig n the holes and secure them w ith one M10 x 1 ¾” Al len Bolt (#31) and ∅ ¾” W asher (#36). Repeat the same procedure to instal l the other side. C.) Attach tw o Bushings [...]

STEP 3 (See Diagram 3) A.) Pl ace the Backrest Board (#12) onto the Backrest Supports (#7) . Secure it with four M 8 x 2” Al len Bolts ( #34) and ∅ 5/8” W ashers (#37). B.) Pl ace the Seat Pad (#11) onto the Seat Support Fr ames (#6). Secure it wi th four M8 x 2” Allen Bolts ( #34) and Ø 5/8” W ashers (#37). DIAGRAM 3 23[...]

STEP 4 (See Diagram 4) A.) Attach the Leg Dev eloper (#5) to the open bracket on the Mai n Frame (#1). Secur e it w ith an Axle ( #14), tw o M10 x ¾” All en Bolts (#30), and tw o ∅ ¾” W ashers (#36). B.) Insert one Foam Tube (#10) hal fway through the hol e on the Main Frame. Inser t two Foam Tubes halfway thr ough the holes on the Leg Deve[...]

STEP 5 (See Diagram 5) A.) Attach the Ar m Curl Pad ( #13) to the Arm C url Stand (#4) . Secure it w ith two M8 x 5/8” Allen Bolts ( #35) and tw o ∅ 5/8” W ashers (#37). Insert the Arm Cur l Stand into the front opening on the M ain Frame (#1) . Use the Lock Knob to hold the desir ed Arm Curl height. B.) The Leg Devel oper can be locked w hen[...]

26[...]

MULTI-PURPOSE BENCH PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Main Frame 1 2 Front Stabilizer 1 3 Rear Stabilizer 1 4 Arm Curl Stand 1 5 Leg Devel oper 1 6 Seat Support Frame 2 7 Backrest Support 2 8 Slidin g Blo ck 1 9 Incline Adjustment Bar 1 10 Foam Tube 3 11 Seat Pad 1 12 Backrest Board 1 13 Arm Curl Pad 1 14 Axle 1 15 Ø 2 3/8” Bushing 2 16 Ol[...]

IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be f ree fr om defects in workm ans hip and m aterial, under norm al us e and ser vice c onditions , f or a period of two years on the Fram e f rom the date of pur chas e. T his warranty extends only to the original purchas er. IMPEX's obligation under this W a[...]