Husqvarna k2500 инструкция обслуживания

E E E E n n n n g g g g l l l l i i i i s s s s h h h h K2500 Oper ator ′ s manual Please r ead the operator’ s manual carefull y and make sur e you understand the instructions before using the machine.[...]

2 – English KEY T O SYMBOLS K ey to symbols W ARNING! The machine can be a dangerous tool if used incorrectly or carelessly , which can cause serious or f atal injur y to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine . Alwa ys wear : • Approv ed pro[...]

English – 3 CONTENTS Contents KEY T O SYMBOLS K ey to symbols ............................................................. 2 CONTENTS Contents ...................................................................... 3 WHA T IS WHA T? What is what on the po wer cutter? ............................... 4 SAFETY INSTR UCTIONS Steps bef ore using a new[...]

4 – English WHA T IS WHA T? What is what on the po wer cutter? 16 17 1 Cutting blade 2 Guard f or the blade 3 Catch f or the guard 4 F ront handle 5 W ater tap 6 Rating plate 7 Switch lock 8 W ater connection with filter 9 Hydraulic hoses 10 Switch 11 Hydraulic motor 12 Flange washer 13 Belt guard 14 Belt tensioner 15 Cutting arm 16 Combination [...]

English – 5 SAFETY INSTR UCTIONS Steps bef ore using a new po wer cutter . • This machine is a h ydraulically operated po wer cutter intended f or free-hand cutting. The machine should be connected to a h ydraulic unit with an oil flow of 35-42 litres/min and a maximum pressure of 150 bar . • Please read the operator’ s manual carefully . [...]

6 – English SAFETY INSTR UCTIONS Switc h lock The s witch lock is designed to pre vent accidental operation of the s witch. When the loc k (A) is pressed in this releases the s witch (B). The s witch lock remains pressed as long as the s witch is pressed. When you release y our grip on the handle this resets both the s witch and the switch loc k.[...]

English – 7 SAFETY INSTR UCTIONS • W ear personal protective equipment. See instr uctions under the heading P ersonal protective equipment. • Ne ver use a machine that has been modified in an y wa y from its original specification. • Ne ver use a machine that is f aulty . Carry out the checks, maintenance and ser vice instructions describ[...]

8 – English SAFETY INSTR UCTIONS • Suppor t the work piece in such a wa y that it is possible to predict what will happen, and so that the cut remains open while cutting. • Check that the b lade is not in contact with anything when the machine is star ted • Alwa ys cut at maximum speed. • Star t cutting smoothly , allowing the machine to [...]

English – 9 SAFETY INSTR UCTIONS • Stand at a comf or table distance from the work piece. • T ak e care when inser ting the blade in an e xisting cut. • Ne ver cut abo ve shoulder height. • Be aler t to mov ement of the work piece or anything else that can occur , which could cause the cut to close and pinch the blade . Pull in Pull in oc[...]

10 – English SAFETY INSTR UCTIONS Check that the b lade is approv ed for the same or higher speed according to the aprov al plate of the engine. Nev er use a cutting blade with a lo wer speed rating than that of the power cutter . Ensure the blade it not cr ack ed or damaged in any other w ay . T est the abr asive disc b y hanging it on your fin[...]

English – 11 ASSEMBL Y Assemb ly Fitting the cutting blade Husqvarna’ s blades are approv ed f or hand-held power cutters. Blades are manufactured with three diff erent diameters of centre holes: 20 mm (0.787"), 22.2 mm (7/8") and 25.4 mm (1"). Bushings can be fitted on the machine axle to adjust the machine to the centre hole o[...]

12 – English ST AR TING AND ST OPPING Starting and stopping Starting • Grip the front handle with the left hand. • Grip the rear handle with the r ight hand. When you g rip the rear handle this releases the s witch lock. Stopping The machine is stopped by releasing the s witch. ! W ARNING! Note the following bef ore starting: Make sure you ha[...]

English – 13 MAINTENANCE Maintenance T ensioning the drive belt The drive belt is fully enclosed and well protected from dust and dir t. When the drive belt is to be tensioned, release the nuts holding the cutting arm. Screw the adjuster scre w so that the square headed nut comes opposite the marking on the cover . This automatically ensures that[...]

14 – English MAINTENANCE ´®z+R=@¶6r¨ ´®z+R=@¶6r¨ Daily maintenance Carr y out the f ollowing chec ks daily bef ore using the machine. 1 Check that n uts and screws are tight. 2 Check that the po wer source (the h ydraulic unit) supplies the correct oil flow and oil pressure . 3 Check that the h ydraulic hoses and couplings are clean and [...]

English – 15 TECHNICAL D A T A T echnical data Note 1: Handle vibrations are measured according to ISO 8662-4 Cutting equipment EC-dec laration of conformity (Applies to Eur ope only) Husqv arna Construction Pr oducts , SE-433 81 P ar tille, Sweden, tel: +46-31-949000, declares under sole responsibility that the power cutter K2500 from year 2006 [...]

´®z+R=@¶6r¨ 2006-12-20 ´®z+R=@¶6r¨ 1150293-26[...]