Husqvarna 115 24 05-95 инструкция обслуживания

W ARNING The engine exhaust fr om this product contains chemicals known to the State of Calif ornia to cause cancer , birth defects or other repr oductive W ARNING Before using our pr oducts, please read this manual carefully to under stand the proper use of y our unit. Operator’ s manual 150BT English 115 24 05-95 150BT_US.fm Page 1 Friday, Apri[...]

English 2 Y OUR WARRANTY RIGHTS AND OBLIGA TIONS The EP A (The US Environmental Protection Agency), CARB (California Air Resources Board), Envir onment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2007 and later small nonroad engine. In U.S. and Canada, new small nonroad engines must [...]

English 3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SAFETY FIRST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Notes on types of warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 W arning labels on the machine . . . . . . . . . [...]

English 4 SAFETY FIRST Instructions contained in warnings within this manual and warning seals marked with a symbol on the blower concern critical points which must be taken into consideration to prevent possible serious bodily injury , and for this reason you ar e requested to read all such instructions carefully and follow them without fail. Note[...]

English 5 For safe operation and maintenance, symbols are carved in relief on the machine. Using to these indications, please be careful not to make a mistake. (a) The port to refuel the "MIX GASOLINE" Position: FUEL T ANK CAP (b) The direction to close the choke Position: INT AKE CUP (c) The direction to open the choke Position: INT AKE [...]

English 6 WORKING CONDITIONS 1. Refrain from operating the blower if you are tir ed, ill, or upset, or if you are under the influence of alcohol, drugs or medication 2. T o reduce the risk of hearing loss associated with sound levels, hearing protection is requir ed. 3. T o reduce the risk of injury associated with thrown objects, always wear eye [...]

English 7 BEFORE ST ARTING THE ENGINE Each time before starting the engine, inspect the entire unit to see if every par t is in good order and is securely tightened in place. If any damage is found in the fuel line, the exhaust line, or the ignition wiring, do not use the blower until it has been repair ed. IMPORT ANT Before starting operation, alw[...]

English 8 MAINTENANCE 1. In order to maintain your product in pr oper working order , per form the maintenance and checking operations described in the manual at regular intervals. 2. Always be sure to turn off the engine and disconnect the spark plug before performing any maintenance or checking procedur es. W ARNING The metallic parts, engine co [...]

English 9 1 . Frame 2. Harness 3. Spark Plug Cap 4. Throttle Lever 5. Net 6. Choke Lever 7. Air Cleaner 8. V olute Case, Cover 9. “CAUTION” Label 10. Elbow 11. Fuel T ank 12. Recoil Starter 13. Stop Switch with Throttle Position Setting 14. Engine Cover 15. Fan 16. Shock Absorber (Rubber) 17. Flexible Hose 18. Pipes 19. Pad 20. Concentrator Noz[...]

English 10 - The data shown above are those in the case of one straight pipe. - Specifications are subject to change without notice. MODEL 150BT Dimensions (L x W x H) mm (in) 351x446x479 (13.8x17.6x18) Dry Weight kg (lbs) (including pipe) 10.2 (22.5) Dry Weight kg (lbs) (without accessories) 9.5 (20.9) Fuel T ank Capacity liter (fl. oz) 1.25 (42[...]

English 11  SWIVEL JOINT 1. Connect the blower and swivel joint with flexible hose. Clamp both ends of the flexible hose securely with the har dware supplied with the unit. NOTE A light lubricant may be used to ease assembl y of flexible hose to blower elbo w .  THRO TTLE LEVER 1. Set up the clamp to the swivel and tighten the screw on the[...]

English 12 Tighten the side straps so that the pressure is evenly distributed acr oss the shoulders.  WAIST BEL T - The waist belt is attached to the rings on the left and right sides of the frame. Place the waist belt around your waist and not too far down on the stomach. Tighten the waist belt strap so that you feel the weight of the blower re[...]

English 13  FUEL W ARNING - Gasoline is very flammable. A void smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground f or fueling and move at least 10ft (3m) away fr om the fueling point before starting the engine . - The engines are lubricated by[...]

English 14  ST ARTING ENGINE IMPORT ANT - A void operating the b lower with the flexible tube and s wivel joint disconnected. That will reduce the cooling air and the engine could be damaged by o verheating. 1. Push the primer bulb until fuel flows out in the clear tube. 2. When the engine is cool, close the choke. (1)Choke Lever (2)Primer Bul[...]

English 15  ADJUSTING IDLE SPEED - The idling speed is set for 2200 rpm at the factory . If it is necessary to adjust the idle speed, use the adjustment screw on the top side of the carburetor . (1)Idling Adjustment Screw  ST OPPING ENGINE - Move the throttle lever to the STOP position. (1)Stop NOTE If the engine does not stop when setting th[...]

English 16 Maintenance, replacement, or r epair of the emission control device and systems may be performed by any non-road engine repair establishment or individual. W ARNING Make sure that the engine has stopped and is cool before perf orming any service to the blower . Contact with rotating blower fan or hot muffler ma y result in a personal in[...]

English 17  SP ARK PL UG - The spark plug may gather carbon deposits on its firing end with reasonable use. Remove and inspect the spark plug every 25 hours and clean the electrodes as necessary with a wire brush. The spark gap should be adjusted to .025 in (0.6 to 0.7mm). - Plug manufacturers r ecommend replacing the plug twice a year to avoid[...]

English 18  IGNITION COIL AIR GAP INSPECTION - If the gap is not accurate or when installing the coil or rotor , adjust the air gap between the ignition coil and the iron cor e of the rotor . Air Gap: 0.40 mm (0.35 to 0.45 mm) / 0.016 in (0.014 to 0.017 in) (1) Rotor (2) Ignition coil  SHOLDER STRAP - If the shoulder strap is damaged it may b[...]