Hunter Fan M0028-01 инструкция обслуживания

www .HunterF an.com 1.888.830.1326 30 inches 7 feet PA G E 2 What to Expect with Y our Installation Ceiling Br acket Ladder PA G E 3 T ools Needed PA G E 6 Hanging the F an PA G E 8 Motor Housing T able of C ontents PA G E 7 PA G E 11 PA G E 14 Maintenanc e, Operation & C leaning T roubleshooting Light Kit ? ? ? PA G E 13 PA G E 5 Prepar ation [...]

www .HunterF an.com 1.888.830.1326 M0028-01 • 06/25/15 • © 2012–2015 Hunter F an Company What t o Expec t with Y our Installation Know your wiring If you are unfamiliar with wiring , use a qualied electrician. Y ou may need a friend to help you . Check box to see fan weight Assess location 30 inches from blade tip to nearest wall or obstr[...]

www .HunterF an.com 1.888.830.1326 T ools Needed Ladder Po wer Drill (optional) 9/64” Drill Bit (optional) Screwdrivers If mounting to a support structure, you will also need these tools . 3 M0028-01 • 06/25/15 • © 2012–2015 Hunter F an Company[...]

www .HunterF an.com 1.888.830.1326 4 M0028-01 • 06/25/15 • © 2012–2015 Hunter F an Company C eiling Bracket OFF Refer to warning w .1 on pg. 2 T o av oid possible elec trical shock, before installing y our fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. T urn Po wer Us[...]

www .HunterF an.com 1.888.830.1326 C eiling Bracket (c ontinued) Prepar ation 1.888.830.1326 www .HunterF an.com Time Sav er Tip: Get a helper to insert grommets, found in the hardware bag , into the blades while you ’r e doing the next couple of steps. 5 M0028-01 • 06/25/15 • © 2012–2015 Hunter F an Company[...]

www .HunterF an.com 1.888.830.1326 Hanging the F an While holding the wires out of the way , lif t the motor assembly and place the square hanger into the opening in the ceiling bracket. Be sure the ground wire attached to the hanger faces out of the large opening in the ceiling bracket. Ground Wire No te: Fan style may vary . Locking Screw Once th[...]

www .HunterF an.com 1.888.830.1326 Wiring F R O M F A N F R O M C E I L I N G B R A C K E T F R O M F A N Using an orange wire connector from the hardware bag , connect the 3 grounding wires (green, green/ yellow stripe , or bare copper) coming from the ceiling , fan, and hanging bracket. (Grounding) Green/Y ellow Stripe Green/Y ellow Stripe White [...]

www .HunterF an.com 1.888.830.1326 With a Phillips head screwdriv er , install the four motor housing screws f ound in the hardware bag . Tighten all four screws securely . Motor Housing Screw Holes Motor Housing Screw Indentation Notch Raise the motor housing up over the motor and ceiling bracket. T urn the motor housing so the screw holes align a[...]

www .HunterF an.com 1.888.830.1326 Blades Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardw are bag. Lightly attach the blade irons to the motor with screws found in the hardware bag , then securely tighten after both screws are attached . 9 M0028-01 • 06/[...]

www .HunterF an.com 1.888.830.1326 F eed the wire plug through the center hole of the upper switch housing , then wrap keyhole slots around the screws and twist counterclockwise. Screw two housing assembly screws from the hardware bag halfwa y into the motor housing . I t does not matter which two screw holes you choose . Insert the third screw , f[...]

www .HunterF an.com 1.888.830.1326 11 M0028-01 • 06/25/15 • © 2012–2015 Hunter F an Company Light Kit Make sure the lower switch housing is securely attached to the upper switch housing. F ailure to properly secur e all three assembly screws could result in the light xture falling. Partially install two of the switch housing screws found [...]

www .HunterF an.com 1.888.830.1326 Light Kit (c ontinued) C ONGRA TULA TIONS! Y OU’RE DONE! No te: Glass shade styl e and number of lights may vary . See next page for fan opera tion instruc tions. Connect the appropriate pull chain pendant to each of the short chains coming from the nial and nial cap . The fan pull chain controls the speed[...]

www .HunterF an.com 1.888.830.1326 Maintenanc e, Oper ation & Cleaning Cleaning the fan - use soft brushes or cloths to prevent scratching . Cleaning products may damage the nishes. Changing the bulbs - unscrew the nial and remove it from the threaded rod . Remove the nial cap and unscrew the globe keeper while supporting the globe wit[...]

www .HunterF an.com 1.888.830.1326 T roubleshooting Exc essive wobbling • Tighten all of the blade and blade iron screws until they are snug . • Use the provided balancing kit and instruc tions to balance the fan. Noisy Operation • Tighten the blade and blade iron screws until they are snug . • Check to see if any of the blades are cracked.[...]