Hunter Fan 52090 инструкция обслуживания

www .HunterF an.com 1.888.830.1326 PA G E 12 PA G E 9 PA G E 5 PA G E 15 PA G E 11 30 inches 7 feet PA G E 2 What to Expect with Y our Installation Ceiling Br acket Ladder PA G E 3 T ools Needed Wiring C anopy Maintenanc e & Cleaning Blades T roubleshooting Downrod Light Kit T able of C ontents ? ? ? PA G E 10 PA G E 14 Mounting Options PA G E [...]

www .HunterF an.com 1.888.830.1326 M0008-01 • 04/14/14 • © Hunter F an Company What t o Expec t with Y our Installation Know your wiring If you are unfamiliar with wiring , use a qualied electrician. Y ou may need a friend to help you . Check box to see fan weight Assess location 30 inches from blade tip to nearest wall or obstruction 7 fee[...]

www .HunterF an.com 1.888.830.1326 3 M0008-01 • 04/14/14 • © Hunter F an Company T ools Needed Ladder Po wer Drill (optional) 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers If mounting to a support structure, you will also need these tools .[...]

www .HunterF an.com 1.888.830.1326 If you ha ve an angled ceiling: 1. Y ou will need a longer downrod (sold separately) . 2. If your ceiling angle is greater than 34°, y ou will also need an Angled Mounting Kit (sold separately) . Guide T ouches BOTH Ceiling & Wa ll S I T U A T I O N 1 Guide T ouches W all but NOT Ceiling S I T U A T I O N 2 Y[...]

www .HunterF an.com 1.888.830.1326 C eiling Bracket OFF F or angled ceilings, point opening toward peak. Refer to warning w .1 on pg. 2 If you are unable to do this, call T echnical Support at 1-888-830-1326. Use wood scr ews (included) when securing to support struc ture with approved electrical outlet box. Drill 9/64” pilot holes in support str[...]

www .HunterF an.com 1.888.830.1326 6 M0008-01 • 04/14/14 • © Hunter F an Company Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Sold Separately Included Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling Standard Downrod for ceilings 8-10’ high Option 1 Option 2 Option 3 skip to nex[...]

www .HunterF an.com 1.888.830.1326 7 M0008-01 • 04/14/14 • © Hunter F an Company KEEP! 8” 3/8” C U T & S T R I P (not to scale) Remove the pr e-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops. The wires can be cut, but leave at least 8” extending from the top o[...]

www .HunterF an.com 1.888.830.1326 Downrod (c ontinued) DO NO T PICK THE F AN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and do wnrod through the canopy . Let the canop y sit loosely on top of the fan. 8 M0008-01 • 04/14/14 • © Hunter F an Company[...]

www .HunterF an.com 1.888.830.1326 Wiring F R O M F A N F R O M C E I L I N G B R A C K E T F R O M F A N Using an orange wire connector from the hardware bag , connect the 3 grounding wires (green, green/ yellow stripe , or bare copper) coming from the ceiling , downrod, and hanging bracket. (Grounding) Green/Y ellow Stripe Green/Y ellow Stripe Wh[...]

www .HunterF an.com 1.888.830.1326 Canop y Position the canop y so that, when lifted into place , the canopy ts into the hanging bracket as shown. No te: Fan style may vary . Lift the canopy into place so that the screw holes are aligned . Screw Holes Insert the two canopy screws found in the hardwar e bag. 10 M0008-01 • 04/14/14 • © Hunter[...]

www .HunterF an.com 1.888.830.1326 Blades Y our blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. F or cleaning the fan, use soft brushes or cloths to prevent scratching . Cleaning agents ma y damage the nishes. Align the three blade holes with the three blade iron posts. Squeeze the blade and the blade ir[...]

www .HunterF an.com 1.888.830.1326 12 M0008-01 • 04/14/14 • © Hunter F an Company Partially install two of the switch housing screws found in the bag . Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Align the notches in the sides of the lower switch housing with the uppe[...]

www .HunterF an.com 1.888.830.1326 Light Kit (c ontinued) C ONGRA TULA TIONS! Y OU’RE DONE! No te: Glass shade styl e and number of lights may vary . See next page for fan opera tion instruc tions. Connect the appropriate pull chain pendant to each of the short chains coming from the nial and nial cap . The fan pull chain controls the speed[...]

www .HunterF an.com 1.888.830.1326 Maintenanc e & Cleaning Changing the bulbs - unscrew the nial and remove it from the threaded rod . Remove the nial cap and unscrew the globe keeper while supporting the globe with your other hand. C arefully remove the globe. Unscrew bulbs and replace with bulbs of same type and wattage. Reinstall the g[...]

www .HunterF an.com 1.888.830.1326 T roubleshooting Exc essive wobbling • Make sure that the blades are properly installed on the blade iron posts. • T urn the power off , support the fan carefully , and check that the hanger ball is properly seated . • Use the provided balancing kit and instruc tions to balance the fan. Noisy Operation • M[...]