Hoshizaki F-330BAH(-C) инструкция обслуживания

® Hoshizaki “A Superior Degree of Reliability” www .hoshizaki.com Model F-330BAH(-C) Self-Contained Flaker Hoshizaki America, Inc. Issued: 5-4-2007 Revised: 9-5-2007 I N S T R U C T I O N M A N U A L[...]

 IMPORTANT Only qualied service technicians should attempt to install, service, or maintain this icemaker. No installation, service, or maintenance should be undertaken until the technician has thoroughly read this Instruction Manual. Likewise, the owner/manager should not proceed to operate the icemaker until the installer has instructed the[...]

3 CONTENTS I. Specications ..................................................................................................................... 4 A. Nameplate Rating ......................................................................................................... 4 B. Dimensions/Connections ..............................................[...]

4 I. Specications A. Nameplate Rating 1. F-330BAH, F-330BAH-C See the nameplate for electrical and refrigeration specications. This nameplate is located on the rear panel. We reserve the right to make changes in specications and design without prior notice. HOSHIZAKI ICE MAKER MOTOR- COMPRESSOR THERM A LLY PRO TECT ED, NOT INTENDED F OR OU[...]

5 B. Dimensions/Connections 1. F-330BAH, F-330BAH-C Unit = inches (mm)[...]

6 II. Installation and Operating Instructions A. Checks Before Installation IMPORTANT 1. Install in accordance with all applicable national, state, and local regulations. . Remove shipping carton, tape, and packing. If any are left in the icemaker, it will not work properly. 3. Ensure all components, fasteners, and thumbscrews are securely in pl[...]

7 C. Location CAUTION This icemaker is not intended for outdoor use. Normal operating ambient temperature should be within +45°F to +100°F (+7°C to +38°C); Normal operating water temperature should be within +45°F to +90°F (+7°C to +3°C). Operation of the icemaker, for extended periods, outside of these normal temperature ranges may affe[...]

8 • Drain line should not be piped directly to the sewer system. An air gap of a minimum of  vertical inches (5 cm) should be between the end of the drain pipe from the unit and the oor drain. • This icemaker must be installed in accordance with applicable national, state, and local regulations. • A plumbing permit and services of a lic[...]

9 G. Final Checklist 1) Is the icemaker level? ) Is the icemaker in a site where the ambient temperature is within +45°F to +100°F (+7°C to +38°C) and the water temperature within +45°F to +90°F (+7°C to +3°C) all year around? 3) Is there at least 4" (61 cm) clearance at top for maintenance or service? 4) Have the shipping car[...]

10 H. Startup CAUTION 1. All parts are factory-adjusted. Improper adjustments may result in failure. . If the unit is turned off, wait for at least 3 minutes before restarting the icemaker to prevent damage to the compressor. 1) Clean the storage bin. ) Open the water supply line shut-off valve. 3) Make sure the power switch on the control bo[...]

11 III. Cleaning and Maintenance A. Cleaning and Sanitizing Instructions IMPORTANT Ensure all components, fasteners, and thumbscrews are securely in place after any maintenance or cleaning is done to the equipment. WARNING 1. HOSHIZAKI recommends cleaning this unit at least twice a year. More frequent cleaning, however, may be required in some exis[...]

1 6) Lift up the top insulation and unsnap the bin control assembly. Lift the assembly up through the insulation and set it aside. See Fig. 4. 7) Remove the top insulation. 8) Remove the thumbscrews attaching spout (B) to the bin, then remove spout (B). See Fig. 5. 9) Remove the thumbscrews attaching spout (A) and safety bracket (A) to the evapo[...]

13 19) When the gear motor starts, remove the front panel and move the ush switch to the "FLUSH" position to drain out the water from the icemaker. 0) After the water has drained, move the power switch to the "OFF" position and unplug the unit. Note: If you do not sanitize the icemaker, leave the unit plugged in with the p[...]

14 4) Remove the top panel. 5) Remove the bin control assembly from the top insulation and set it aside. Remove the top insulation. 6) Remove the thumbscrews attaching spout (B) to the bin, then remove spout (B). 7) Remove the thumbscrews attaching spout (A) and safety bracket (A) to the evaporator assembly, then remove spout (A) and safety bracket[...]

15 B. Maintenance IMPORTANT 1. This icemaker must be maintained individually, referring to the instruction manual and labels provided with the icemaker. . To achieve optimum icemaker performance, the following parts need periodic inspection and maintenance: Extruding Head and Upper Bearing Housing and Lower Bearing Evaporator Cylinder Auger Gear[...]

16 C. Preparing the Icemaker for Long Storage CAUTION When the icemaker is not used for two or three days under normal conditions, it is sufcient to only move the power switch to the "OFF" position. When storing the icemaker for extended time or in sub-freezing temperatures, turn the water off and drain out all water from the water lin[...]

17 HOSHIZAKI AMERICA, INC. 618 Hwy . 74 S., Peachtree City , GA 30269 USA TEL (770) 487-2331 F AX (770) 487-3360 www .hoshizaki.com 91A2SA10B[...]