Honeywell T8132B инструкция обслуживания

1 69-0803—1 OWNER’S GUIDE 69-0803-1 T8132A/T8132B Electronic Programmable Thermostat[...]

2 69-0803—1[...]

3 69-0803—1 T able of Contents Programming Y our Thermostat .................................................................................................... .. 4 Program Schedule ............................................................................................................... ........ 6 Set Current Time/Day .....................[...]

4 69-0803—1 Programming Y our Thermostat The thermostat can be programmed in your hand before it is installed if the batteries are installed or after it is on the wall. If you need to install or replace the batteries, refer to the Maintaining Y our Thermostat section. The following personal Program Schedule can be helpful for planning your progra[...]

5 69-0803—1 depending on the outside temperature and your furnace response time, to give the furnace a head start to heat the house before you arrive home. SLEEP is the time period you can set for an energy-saving temperature while you are sleeping. (For more comfortable sleep- ing, some homeowners choose not to raise the cool temperature during [...]

6 69-0803—1 Program Schedule Heating Program Schedule W eekdays Star t Time Heating T emperature Cooling T emperature W AKE __________ ____________________ ____________________ LEA VE __________ ____________________ ____________________ RETURN __________ ____________________ ____________________ SLEEP __________ ____________________ _____________[...]

7 69-0803—1 IMPORT ANT Batteries are required for operation and programming. When inserting the batteries, set the system s witch to OFF . Remove the battery door (on the ther mostat left side) using a coin at the bottom. See Maintaining Y our Thermostat section. Set Current Time/Day To set the time, press and release the Set Clock/Da y ke y once[...]

8 69-0803—1 Use the Time ke ys to program W AKE time and use the T emp ke ys to program the W AKE temperature for Mon-Fri. Repeat the sequence f or LEA VE, RETURN, and SLEEP . Press the Set Schedule ke y until W AKE, SA SU and SET appear on the displa y . Use the Time ke ys to program W AKE time and the T emp ke ys to program W AKE temperature f [...]

9 69-0803—1 Check Programs  Press Set Schedule key repeatedly to view each time and temperature on the display . Press the Run Program key once to return to the program. Cancel a program—Press the Set Schedule key until the program to cancel shows. Pressing the two Time keys together cancels the program. Permanently Change a program—Repeat[...]

10 69-0803—1 Setting System Switch System switching positions control thermostat operation as follows: COOL: The thermostat controls the air conditioning system. OFF: Both the heating and air conditioning systems are off . HEA T: The thermostat controls the heating system. M5783 Auto On Fan Cool Off Heat System FAN SWITCH SYSTEM SWITCH TU AM LEAV[...]

11 69-0803—1 Maintaining Y our Thermostat Installing Batteries IMPORT ANT Batteries must be installed for prog ram- ming and operation of the thermostat and heating/cooling system.  Purchase two AA alkaline batteries; non- alkaline batteries do not last as long, and can leak causing damage to the thermo- stat or wall surf ace. W e recommend En[...]

12 69-0803—1 starts flashing. If the batteries are not replaced when bAt Lo is flashing, the indicator eventu- ally stops flashing. When bAt Lo stays on without flashing, the thermostat and heating/ cooling system have stopped working and the batteries are almost completely dead. After the batteries are completely dead, the bAt Lo indicator disap[...]

13 69-0803—1 T roubleshooting Guide I F… THEN… Display will not come on. • Set the system switch to OFF. Remove the batteries. Insert backward for at least five seconds to reset the thermostat. Correctly replace the batteries. Display should come on. • Make sure batteries are fresh and installed correctly. • Gently clean battery contact[...]

14 69-0803—1 Heating will not come on. • Check that the switch on the thermostat is set to HEAT. Allow a minimum of five minutes for time guard protection to expire. • Check the system fuse or circuit breaker and replace or reset, if necessary. • If the display is blank or displays bAt Lo , install fresh batteries. • If the temperature se[...]

15 69-0803—1 Cooling will not come on. • Make sure the outdoor disconnect is engaged (on). (Cont) • If the temperature setting is lower than the current temperature, and the SYSTEM ON indicator is lit, move the system switch from COOL to OFF for ten minutes. After ten minutes, return the switch to the COOL position. If the air conditioner com[...]

16 69-0803—1 NO TICE This equipment is a Class B digital apparatus, which complies with Canadian Radio Interference Regulations, CRC c.1374. The thermostat current temperature setting does not match the display • Check that the wiring hole in the wall behind the wallplate was plugged with insulation to prevent drafts that could adversely affect[...]

17 69-0803—1 Notes[...]

18 69-0803—1 Notes[...]

19 69-0803—1 Limited One-Y ear W arranty Carrier warrants this product, excluding battery , to be free from defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase b y the consumer. If , at any time during the warranty period, the product is defectiv e or malfunctions, Carrier [...]

20 69-0803—1 Printed on recycled paper containing at least 10% post-consumer paper fibers. 69-0803—1 J.S . Re v . 5-96 Printed in U.S.A. Copyright © 1996 Honeyw ell Inc. All Rights Reserved www .honeywell.com/yourhome Home and Building Control Honeywell Inc. 1985 Douglas Drive North Golden Valley, MN 55422 Helping You Control Your World Home a[...]