Harbor Freight Tools 95671 инструкция обслуживания

Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at: http://www .harborfreight.com Cop yr ight © 2007 by Harbor F reight T ools ® . All rights reser ved. No por tion of this manual or any ar twork contained herein may be reproduc[...]

PR ODUCT SPECIFICA TIONS SA VE THIS MANU AL Y ou will need this manual f or the safety warnings and precautions, assembly , operating, inspection, maintenance and cleaning pr ocedures, par ts list and assembly diagram. Keep y our in voice with this man ual. Write the in voice n umber on the inside of the front co ver . K eep this manual and in v oi[...]

3. Keep bystanders, children, and visitors away while operating welding equipment. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. Children should not be allowed in the work area. 5. Dress properl y . Do not wear loose clothing or jewelry . Cont[...]

13. T ool service must be perf ormed only b y qualified repair personnel. Ser vice or maintenance perf or med by unqualified personnel could result in a risk of injur y . 14. When servicing a tool, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthorized[...]

structure, as in walls or ceilings , without an approv ed method for eliminating the hazard. Do not dispose of hot slag in containers holding combustible materials. K eep a fire e xtinguisher nearby and kno w how to use it. After welding or cutting, make a thorough e xamination f or evidence of fire . Be aw are that easily visible smoke or flame ma[...]

7. Read and understand all instructions and saf ety precautions as outlined in the manufacturer’ s manual for the material y ou will weld or cut. 6. Alwa ys keep the W elding Hoses (7, 8) awa y from mo ving par ts on the tool. Examine the W elding Hoses f or cuts, bu r ns, or worn areas before each use . If any damaged areas are f ound, replace t[...]

chemical known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety Code 25249.5 et seq.) When unpacking, chec k to make sure all the par ts sho wn on the P ar ts List on page 11 are included. If an y par ts are missing or broken, please call Harbor F reight T ools at the number shown on th[...]

5. IMPOR T ANT! The Pressure Adjusting Scre w on the Acetylene Regulator (not included) and the Pressure Adjusting Screw on the Oxygen Regulator (not included) should be opened slightly by turning counterclockwise to relie ve pressure on the regulator diaphragms bef ore opening the cylinder valv es. If this is not done, pres- sure from the cylinder[...]

8. Depending on use, attach a Tip (1, 12, 13, 14, 15) to the Mixer (2) on the T orch Handle (5). (See Figure B.) 9. Open the Oxygen V alve Stem (9) on the T orch Handle (5). Adjust the Oxygen Regulator to the desired working pressure. Then, close the Oxygen V alv e Stem on the T orch Handle. (See Figure B.) 10. Open the Acetylene V alve Stem (10) o[...]

INSPECTION, MAINTENANCE, AND CLEANING 1. W ARNING! Make sure the Welding T orch Mini-Kit is cool to the touc h and disconnected from its o xygen and acetylene cylinder s before performing any inspection, maintenance, or cleaning procedures. 2. BEFORE EA CH USE, inspect the general condition of the W elding T orch Mini-Kit. Check f or loose screws ,[...]

NO TE: Some par ts are listed and shown f or illustration pur poses only , and are not av ailable individually as replacement parts. P ARTS LIST AND ASSEMBL Y DIA GRAM 12 13 14 15 SKU 95671 For technical questions, please call 1-800-444-3353 P AGE 11 Par t # Des cr ip ti o n Qt y. Par t # Des cr ip ti o n Qty . 1 Welding Tip (0.2m m) 1 9 Valve Stem[...]