Harbor Freight Tools 93815 инструкция обслуживания

4 T ON ELECTRIC LOG SPLITTER Model 93815 ASSEMBL Y AND OPERA TING INSTR UCTIONS 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at: http://www .harborfreight.com Cop yright © 2006 b y Harbor F reight T ools ® . All r ights reser ved. No por tion of this manual or any ar twork contained herein ma y be reproduced in an y shape or [...]

PR ODUCT SPECIFICA TIONS I t em Descri pt i on El ect r i c M ot or 2 HP , 110 V, 60 Hz, S i ngl e Phase, 1150 W at t s Power Cor d 14 AW G x 3 C, Doub l e I nsu l at ed M eas ur ed Am per age 8. 1 w i t h no l oad 10 wi t h l oad 30 at st ar t - up M ax i m um For ce 4 Tons ( 8, 000 Lbs . ) Log Si ze Capaci t y 20” L x 10” D W edge Si ze 5” [...]

ELECTRICAL SAFETY 4. Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding pr ong or modify the plug in any wa y . Do not use an y adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the[...]

12. A v oid accidental star ting. Be sure the P ower Switch is off bef ore plugging in. Plugging in the splitter with the P ower Switch on, in vites accidents . 13. Remove adjusting keys or wrenches before turning the splitter on. A wrench or a ke y that is left attached to a rotating par t of the pow er tool ma y result in personal injur y . 14. D[...]

23. Use only accessories that are recommended by the manufacturer for your model. Accessories that ma y be suitable f or one tool ma y become hazardous when used on another tool. SER VICE 24. Log Splitter service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of[...]

2. Always wear safety impact eye goggles and heavy work gloves when using the splitter . Using personal saf ety de vices reduce the risk for injury . Safety impact ey e goggles and heavy work glov es are av ailable from Harbor F reight T ools. 3. Maintain a safe working en vironment. K eep the work area well lit. Make sure there is adequate surroun[...]

GROUNDING W ARNING! GR OUNDED T OOLS: T OOLS WITH THREE PRONG PLUGS 1 . T ools mar ked with “Grounding Required” ha v e a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet. If the tool should electrically malfunction or break down, grounding provides a low resistance path to carr y electric[...]

EXTENSION CORDS 1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of p[...]

6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W -A” (“W” in Canada) to indicate it is acceptable f or outdoor use. 7. Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using [...]

UNP A CKING When unpacking, check to make sure all the parts shown on the Parts List on page 14 are included. If any par ts are missing or brok en, please call Harbor F reight T ools at the number shown on the cover of this manual as soon as possible. The only assembly required is as follows: Screw Handle A (D Below) into Handle B (E Below). The Lo[...]

OPERA TING INSTR UCTIONS NO TE: For additional inf or mation regarding the par ts listed in the follo wing pages , ref er to the Assembly Diagram on page 15 . Please Refer to Figure D on page 10 in following these instructions. 1. Plan your w ork site . W or k saf ely and sa v e eff or t b y planning y our work bef ore hand. Have your logs position[...]

9. Stack as y ou work. This will pro vide a saf er work area, by k eeping it uncluttered, and avoid the danger of tripping, or damaging the power cord. 10. Remember to retighten the Bleed Screw (14) when you are finished. INSPECTION, MAINTENANCE, AND CLEANING 1. W ARNING! Mak e sure the Switch (36) of the splitter is in its “OFF” position and t[...]

W arning: Be sure to dispose of the dir ty oil pr operl y . T ake it to your local waste oil recyc ling center . Ne ver dump it on the gr ound or mix it with trash. Refilling the Hydraulic Oil 1 . P eriodically check the le v el of the oil. It must be between the two notches on the low er end of the Dip Stic k. If the oil lev el is low , refill usi[...]

P ARTS LIST SKU 93815 P A GE 14[...]

ASSEMBL Y DIA GRAM SKU 93815 P A GE 15 NO TE: Some par ts are listed and shown f or illustration pur poses only , and are not a v ailable individually as replacement par ts.[...]

SKU 93815 P A GE 16 Harbor Freight T ools Co . makes e ver y effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from def ects in materials and wo r kmanship for the pe r iod of ninety da ys from the date of purchase. This warranty does not apply to damage d[...]