Harbor Freight Tools 90692 инструкция обслуживания

LA THE DUPLICA T OR A TT A CHMENT (FOR USE WITH LA THE MODEL 90265) MODEL 90692 ASSEMBL Y AND OPERA TING INSTR UCTIONS 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at http//www .harborfreight.com Cop yr ight 2003 by Harbor F reight T ools. All rights reser v ed. No portion of this manual or any ar twork contained herein ma y be[...]

PR ODUCT SPECIFICA TIONS SA VE THIS MANU AL Y ou will need this manual for the safety warnings and precautions, assembly , operating, inspection, maintenance and cleaning procedures, parts list and as- sembl y diagram. Keep your in voice with this man ual. Write the in voice n umber on the inside of the front co ver . K eep this manual and in voice[...]

SKU 90692 P A GE 3 3. Store idle equipment. When not in use, tools and equipment should be stored in a dr y location to inhibit rust. Alwa ys lock up tools and equipment, and k eep out of reach of children. 4. Do not use this product if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgement or r[...]

SKU 90692 P A GE 4 cannot cov er all possible conditions and situations that ma y occur . The operator must understand that common sense and caution are factors, which cannot be b uilt into this product, but must be supplied b y the operator . SPECIFIC PRODUCT W ARNINGS AND PRECA UTIONS 1. This Lathe Duplicator Attachment is designed f or use ONL Y[...]

SKU 90692 P A GE 5 ASSEMBL Y INSTR UCTIONS NOTE: For additional references to the parts listed in the following pages, refer to the Assembly Diagram on page 14 . T o Attac h The T ool Rest Base: 1. Loosen the T ool Rest Handle of the lathe , and slide the T ool Rest Base of the lathe to as near the Headstock of the lathe as possibl e. (See Figure A[...]

SKU 90692 P AGE 6 3. Install one Low er V er tical Suppor t Bar (46) onto the T ool Rest Base of the lathe , and secure it by tightening the Suppor t Bar Handle of the lathe. (See Figure A.) 4. Loosen the T ailstock Handle of the lathe , and remov e the T ailstock from the Bed of the lathe . (See Figure B.) T AILST OCK HANDLE T AILST OCK 5. Loosen [...]

SKU 90692 P AGE 7 U-BRACKET (38) HANDLE (3) P A TTERN SUPPORT B AR (41) P A TTERN BOL T (42) LOWER VERTICAL SUPPORT BAR (46) U-BRACKET ASSEMBL Y LOWER VERTICAL SUPPORT BAR (46) U-BRACKET ASSEMBL Y FIGURE C T o Attac h The Suppor t Bar: 1. Remove the End Cap (12) from each end of the Support Bar (54). (See Assy . Diagram.) 2. Remove the two Square N[...]

SQUARE NUT (47) SQUARE NUT (47) SUPPORT BAR (54) FLA T W ASHER (40) LOCKW ASHER (34) HANDLE (48) FLA T W ASHER (40) LOCKW ASHER (34) HANDLE (48) FIGURE D T o Assemb le The T ool Holder: 1. Loosen the two Set Scre ws (20) on the T ool Holder (24), and e xtend the Cutting T ool (31) out about 4 inches. Then re-tighten the two Set Screws to secure the[...]

T o Attac h The T ool Holder Assemb l y: 1. Slide the Cutting T ool (31) of the T ool Holder (24) into the Slot located on the Side Plate (50). (See Figures E and F .) 2. Attach the Spring (19) over the Pointer (14) on the Side Plate (50). (See Figure F .) 3. Adjust the Spring (19) so that there is enough tension to keep the T ool Holder (24) firml[...]

FIGURE G SAFETY SHIELD (8) HANDLE (51) SAFETY SHIELD PLA TE (43) SUPPORT BAR (54) BOL T P AN HEAD SCREW (9) FLA T W ASHER (21) HEX NUT (7) HEX HEAD BOL T (11) FLA T W ASHER (40) HEX NUT (39) OPERA TING INSTRUCTIONS T o Adjust The Cutting T ool: 1. Prior to use, the Cutting T ool (31) must be set appro ximately 1/8” above the Spindle of the lathe [...]

3. The Cutting T ool (31) also can be adjusted vertically by loosening the Soc ket Head Bolt (25) which secures the T ool Holder (24) in place. Once adjusted, make sure to re-tighten the Socket Head Bolt. (See Figure H.) 4. The Cutting T ool (31) can be adjusted horizontally b y moving the T ool Rest Base across the Bed of the lathe, towards or awa[...]

SKU 90692 P A GE 12 occurs, have the problem corrected before further use. Do not use damaged equipment. 2. F or better and safer perf or mance, alw ays k eep the Cutting T ool (31) clean and sharp. 3. Daily , with a clean cloth, br ush, or vacuum remo ve all debris fromthe Lathe Dupli- cator Attachment. Then, use a lightweight machine oil to lubr [...]

P AR TS LIST SKU 90692 P AGE 13 PLEASE READ THE FOLLO WING CAREFULL Y THE MANUF A CTURER AND/OR DISTRIBUT OR HAS PRO VIDED THE P ARTS LIST AND ASSEMBL Y DIA GRAM IN THIS MANU AL AS A REFERENCE T OOL ONL Y . NEI- THER THE MANUF A CTURER OR DISTRIBUT OR MAKES ANY REPRESENT A TION OR W ARRANTY OF ANY KIND T O THE BUYER THA T HE OR SHE IS QU ALIFIED T [...]

NO TE: Some par ts are listed and shown f or illustration pur poses only , and are not available individually as replacement parts. ASSEMBL Y DIA GRAM SKU 90692 P AGE 14 12 38 3 45 2 39 41 42 49 54 53 52 50 51 16 32 38 1 23 22 21 13 24 30 25 26 27 5 28 29 6 20 19 46 31 33 32 18 34 35 36 37 14 15 17 39 41 42 2 48 34 40 1 38 3 12 45 44 46 47 39 49 10[...]