Haier HBS82-880 инструкция обслуживания

HBS82-880 A utomatic Drum W ashing Machine Operation Manual Ta b le of Contents Before using Names of Parts--------------inside front cover Matters Needing Attention--------------------1-3 Installation----------------------------------------4-5 Control Panel---------------------------------------6 Operational Functions------------------------6-7 Du[...]

Names of Parts Detergent distributor To p program knob Operation button Door Porthole Drainage hose clip Back plate Earth terminal Power supply cable Back plate screw (3) Packing bolt (3) T emperature knob Caution and W arning symbols For your safety and to prevent damages to the washing machine, any instructions in this manual with this “Stop”[...]

1 Matter s Needing Attention 1. A separate earthed socket is required f or the power supply . After installation of the washing machine,the power plug should be accessible during the normal wash. 3. Fuses in the power circuit should be rated for 15A. Refer to a washing machine techni- cian or a Haier designated service point for power cable replace[...]

2 Matter s Needing Attention 9. The washing machine should be place in a well ventilated area maintaing a space between walls or furniture. 10. Keep away from heat sources and direct sunlight to prevent plastic and rubber com- ponents from aging. 8. The washing machine must not be used in the open or in area of high moisture as water droplets may f[...]

3 Matter s Needing Attention 9. Keep the door slightly open when the washing machine is not being used. Never cover the machine with a plastic sheet. 4. Do not wash foam rubber or similar sponge materials. 5. Before washing, do up zippers, buttons ,laces and repair damaged areas,underwear or small articals should be placed in the laundry bag or a p[...]

Installation 4 Fig 1 As shown in figure1 remov e all the packing materials (including the foam base). Remove the packing screws as shown in figure 2. The packing bolts protect the appliance from shock during transpor tation The steps below should be f ollowed bef ore using the appliance, 1. Remove the rear panel of the washing machine; 2. remove th[...]

5 Installation Connection of water inlet hose and washing machine 1. Place the water inlet hose nut on the connector of the water inlet valve. 2. slightly shake the water inlet hose nut to see if it is tightly and properly fixed. connector of water inlet valve water inlet hose nut W ater drainage hose The height of the terminal of the water drainag[...]

6 Control Panel A W ashing program Tu rn the knob cloc kwise to set the desired wash program . Caution: T urn off the power and turn the program knob clockwise for setting desired wash program. B W ashing temperature Tu rn the knob clockwise to set the desired temper ature. T emperatures between 30 O C-90 O C can be setted , Cold w ash is se- lecte[...]

7 Operational Functions G Power light The light will illuminates when the power supply is connected. F Power button Press the button ,washing machine will working;release the button, the washing machine will stop. ON OFF ON OFF 7 E Economic wash button Pressing this button will reduce the consumption of water during bleaching under intense wash. It[...]

8 Program Selection NOTE: “o”means softener liquid detergent canbe added when necessary. “ ”means detergent can be added when necessary. “ ”means no detergent can be added. 8 15 20 20 45 22.5 5 12.5 5 10 5 25 10 7.5 7.5 25 10 7.5 7.5 x[...]

9 1. Power supply Plug in the power supply 220V~/50Hz. 3. Laundry treament 2. Water supply Tu rn on the tap ensure that the water is clear . Caution: Before staring the washing machine turn on the water faucrt to ensure that the water faucet and the water inlet hose are connected correctly and do not leak. sort out clothes according to type and ext[...]

W ashing Methods 10 1. Laundry loading Evenly load the laundry in the washing machine and then tightly close the door of the washing machine Note: 1) When first using the washing ma- chine, let it run unloaded for one program to prevent the laundry from being tainted by oil or dirty water from the washing ma- chine. 2) Do not overload the washing m[...]

11 W ashing Methods 7. End W ait 2-3 minutes after the washing process is finished, press the power b utton again to cut off the power supply . Open the door to take out the laundr y . T urn off the tap and unplug the washing machine. 5. Selecting the function button Select function buttons as required (refer to the directions printed on the operat[...]

12 Maintenance 6. If the machine is to be moved a distance location, replace the vibration mounting locks which were re- moved during installation as shown below. 1. T urn of the water and electricity supply after every wash. Open the door to pre- vent the formation of moisture and odors. If the washing machine is left idle for a long period, drain[...]

13 Tr ouble shooting The following circumstances do not constitute problems. Do not contact the main- tenance service until the problem has been confirmed. Problem Possible Cause Poor connection to power supply Power failure Door is not properly closed Machine has not been switched on W ashing machine does not fill with water Water is not turned on[...]

14 Te c hnical Specification Model Item Power supply HBS82-880 220V~/50Hz Maximum working current (A) W ater pressure (MP a) W ashing power (W) Spinning power (W) 0.05 P 1 330 650 10 Heating power (W) Size (HXDXW) (mm) W eight (kg) 15 1950 72 850x550x595 W ashing program 14 HBS82-880[...]

I1: Power Switch EV C ,EVP ,EVL: W ater valv e I2: Economic wash Switch P1,P2: Pressure Switch I3: No spin Switch THR: Adjustable Ther mastat MR: Door Lock D: Drain Pump TM: Timer motor MC,ML: Motor H:Heating Element C: Capacitance Wiring Cir cuit 15 15 I3: No spin Switch I2: Economic wash Switch[...]