Haier AU162AFNAA инструкция обслуживания

AS182A TNDA AU182AFNBA (HSU-18CW03/R1) AS162A TNCA AU162AFNAA (HSU-16CW03/R1) AS072AZBDA AU072ABBAA (HSU-07HW03/R1) AS072AZNDA AU072ABNAA (HSU-07CW03/R1)[...]

Contents Cautions Parts and functions Operation Maintenance T rouble shooting 1-2 3-6 7-14 15-17 18[...]

Cautions Disposal of the old air conditioner Before dispos ing an o ld air condit ioner that goes out of use, please make sure it's inoperative and safe. U nplug the air conditioner in order to avoid the risk of child entrapment. It m u s t b e n ot i c e d t h a t ai r c o nd i t i on e r s y s t e m c o n t a i n s r e f r i g e r a n t s , [...]

Cautions Always remember to unplug the air conditioner before opening inlet grill. N e v e r u n p lu g y o u r a i r c o n d i t i o n e r b y pulling on the power cord. Always grip plug firmly and pull straight out from the outlet. All electrical repairs must be carried out by qualified electricians. Inadequate repairs may result in a major sourc[...]

P ar ts and Functions Indoor Unit AS182A TNDA AU182AFNBA (HSU-18CW03/R1) AS162A TNCA AU162AFNAA (HSU-16CW03/R1) AS072AZBDA AU072ABBAA (HSU-07HW03/R1) AS072AZNDA AU072ABNAA (HSU-07CW03/R1) Power Operation mode indicator Lights up when Timer operation is selected. Lights up during compressor running. Inlet grill Air filter Vertical flap Use remote co[...]

AU182AFNBA (HSU-18CW03/R1) AU162AFNAA (HSU-16CW03/R1) AU072ABBAA (HSU-07HW03/R1) AU072ABNAA (HSU-07CW03/R1) For models: For models: 14 Power Failure Resume (to be applied for a necessary situation): Setting Method: When the remote controller is on (excluding timer mode and fan mode), press the " SLEEP " button on the remote controller 10 [...]

O N O F F TEMP SWING MODE CLOCK SLEEP SET LOCK RESET TIMER FAN OFF ON AUTO AM PM AM PM AM PM P ar ts and Functions Buttons and display of the remote Power TEMP. FA Used to set auto fan Used to set correct Used to set correct time Used to select  TIMER ON, TIMER OFF, Used to lock buttons Used to set clock and Used to select fan speed: Used to sel[...]

O N O F F TEMP SWING MODE CLOCK SLEEP SET LOCK RESET TIMER FAN OFF ON AUTO AM PM AM PM AM PM P ar ts and Functions Buttons and display of the remote Operation Hints AUT AUT DR AUT FAN Clock TEMP FAN HEA When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: Press CLOCK button[...]

[...]

Unit will run in selected mode. Stop display at " " AUTO or " " FAN. Oper a tion Enjoy yourself by just a gentle press. (1) Unit start (2) Select operation mode (3) FAN (4) Unit stop AUT AUT AUT DR HEA FA Press ON/OFF button, unit starts. Previous operation status appears on display. (Not Timer setting) Press MODE button. For ea[...]

Oper a tion AUT DR HEA FA COOL AUT AUT LO MED HI (1) Unit start (2) Select operation mode (3) Select temp.setting Press MODE button. For each press, operation Unit will run in operation mode displayed on LCD. Press FAN button. For each press, fan speed changes Hints (4) Fan speed selection Unit will start running to reach the temp. setting on Recom[...]

After operation mode is selected, vertical flap will open automatically according to the mode. Referring to the Fig. Oper a tion When humidity is high, condensate water  might occur at air outlet if all horizontal  louvers are adjusted to left or right. Unit won't restart until 3 minutes have  elapsed, due to system protection. HEAT m[...]

Oper a tion TIMER operation Hints Set Clock correctly before starting Timer operation(referring to page 6) You can let unit start or stop automatically at following times: Before you wake up in the TIMER ON/OFF (2)TIMER mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as Select your desired T[...]

Oper a tion TIMER ON-OFF (1)After unit start, select your desired operation mode Operation mode will be displayed on LCD. Power indicator on indoor unit lights up. (2) Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: Select TIMER ON-OFF. "ON" will (3)Time setting for TIMER ON Press HOU[...]

Oper a tion Emergency Carry out this operation only when the remote controller is defective or lost. When the emergency operation switch is pressed, a " Pi " sound starts once, which means the start of this operation. In this operation, it is not possible to change the  settings of temperature and air flow speed, it is  also impossi[...]

Oper a tion In COOL mode In HEAT mode Approx. 6 Temp. Unit stop Temp. Unit stop Approx. 3 Note: In AUTO mode, unit will run in SLEEP  function according to operation mode. In FAN mode, comfortable sleep is not  available. Fig.1 Fig.2 Comfortable SLEEP Before going to bed at night, you can simply press the SLEEP button and unit will bring you [...]

Maintenance Cut off power supply  before cleaning wipe unit casing with soft cloth. In case of heavy stain, clean it with neutral detergent. squeeze water in the cloth, wipe off the detergent on unit Cleaning of unit casing Cleaning of remote controller Cleaning of air filter Don't use water to wash unit casing, please use dry cloth. Don&ap[...]

Maintenance[...]

Maintenance Proper room Closing of doors and windows  during operation. Effective use of the Never fail to observe the Do not block the inlet or outlet. Do not use for other Do not pull power plug. Once every Avoid time- wasteful Better use of air conditioner Cleaning of the air filter. Proper temperature Curtains or blinds for windows Do not sp[...]

T r ouble Shooting Before asking for service, check the following first. Cause or check Normal Performanc e Smells are Mist or steam are blown Multiple  check Is power plug inserted? Is there a power failure? Is fuse blown out? Poor Phenomenon When unit is stopped, it won't restart immediately until 3 minutes have elapsed  to protect the[...]