Grizzly H6143 инструкция обслуживания

COPYRIGHT © AUGUST, 2005 BY GRIZZLY INDUSTRIAL, INC., REVISED DECEMBER, 2007 (TS) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #TR7323 PRINTED IN CHINA M O D E L H 6 1 4 3 1 6 G A U G E F I N I S H N A I L E R INSTRUCTION MANUAL[...]

Safety Instructions For Pneumatic Tools 1. KEEP ALL SAFETY DEVICES IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND WRENCHES . Form habit of check- ing to see that keys and adjusting wrenches are removed from tool before operation. 3. KEEP WORK AREA CLEAN . Cluttered areas and benches invite accidents. 4. DO NOT USE IN DANGEROUS ENVIRONM[...]

H6143 16 Ga. Finish Nailer -1 - 10. USE PROPER AIR HOSE for the tool. Make sure your air hose is in good condition and is long enough to reach your work without stretching. 11. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neck - ties, rings, bracelets, or other jew- elry which may get caught in moving parts. Non-slip footwear is recom- [...]

H6143 16 Ga. Finish Nailer -2 - 1. HAND INJURIES: Do not place your hands near the nail point of entry. A nail can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 2. COMBUSTIBLE GASES: Never connect the nailer to pressurized oxygen or other combustible gases as a power source . Only use fil- tered, lubricated[...]

H6143 16 Ga. Finish Nailer -3 - Operating this nailer can propel objects into the air, causing imme- diate eye damage. To protect your- self, always wear American National Standards Institute (ANSI) approved safety glasses or goggles when oper- ating this equipment. In addition, this nailer discharges at approximately 85-90 decibels. To protect you[...]

H6143 16 Ga. Finish Nailer -4 - INTRODUCTION If you have any c omme nts re gard ing th is man ual, pl ease w rite to u s at th e follo wing add ress : Grizzly Industrial, Inc. C/O Technical Documentation Manager P.O. Box 2069 Bellingham, WA 98227-2069 Mo st i mpor t antl y , we st and b ehi nd o ur too ls. If you have any ser vi ce que sti ons or p[...]

H6143 16 Ga. Finish Nailer -5 - SET UP Figure 1. Model H6143 inventory. Unpacki ng Y our Mo del H 6 143 l eft ou r ware hous e in a c arefu lly pac ked b ox. If you di scover th e nai ler is dam age d af ter you have sig ned fo r del iver y , pl ease i mme diat ely cal l Cus tomer Ser vice at ( 5 70 ) 546 -9 66 3 for advic e. Save th e co ntai ners[...]

H6143 16 Ga. Finish Nailer -6 - Compressed Air Sy stem The M ode l H 61 4 3 is des igne d to b e o per- ated at 60 –1 0 0 PSI using c lean, dr y , reg u- late d, c ompr ess ed a ir . DO NO T exce ed th e 120 P SI m axi mum op er atin g pre s- sur e fo r you r m ode l. Befo re u sing your new n ailer, reg ulate the air pr essu re on you r air co m[...]

H6143 16 Ga. Finish Nailer -7 - Safety Nose Mechanism A s afety me cha nis m on the no se o f the nai ler p rotec ts ag ain st ac ci dent al f irin g. Whe n the tri gge r is pres sed, t he nail er will not fire un til th e safet y nos e me cha nism is dep ress ed. Befo re you us e your nai ler for t he fir st tim e, chec k the safet y nose me chan [...]

H6143 16 Ga. Finish Nailer -8 - OPERATIONS Loadin g Figure 3. Sliding magazine pusher back and engaging catch lever. When replacing nails in your Model H6143, follow these guidelines: Gauge: 16 Length: 1 1 ⁄ 4 " – 2 1 ⁄ 2 " Capacity: 74 To load your nailer: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. Grip the nailer firmly, and pul[...]

H6143 16 Ga. Finish Nailer -9 - Figure 6. Depth adjustment controls. A depth adjustment knob is attached to the nose for setting the nail depth. To adjust the dep th: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. Rotate the adjustment knob ( Figure 6 ) clockwise to drive the nails deeper or counterclockwise to drive the nails shallower. 5. Pull the [...]

H6143 16 Ga. Finish Nailer -10 - A jammed nail m ust be cleared before using the nailer again. To clear a jammed nail from the dis- charge area: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. Pull back and latch the magazine pusher. 3. Remove the nail stick from the maga- zine. Cleari ng Jammed Nails Figure 7. Nose opened to clear a jam. Nose Cover N[...]

H6143 16 Ga. Finish Nailer -11 - Replacin g Pist ons / O - Rin gs If yo u use your nail er day i n an d day out , re pair pist ons are cheap ins uran ce agai nst wa sted d own tim e and lo st prof its, in t he event t hat a p isto n or p isto n shaf t bec ome s wo rn out. For yo ur co nvenie nce, refer to th e par ts brea kdown dur ing thi s pro ce[...]

H6143 16 Ga. Finish Nailer -12 - CLEANING & LUBRICATION Cleanin g Use a go od so lvent to c lean t he n ose ass emb ly of the nai ler . Al ways be sure tha t th e n ailer is dr y before us ing it a gain. Do n ot all ow du st, c hip s, san d, etc . i nto the ai r c onne cto rs or into t he b od y of t he nai ler; t his may re sul t i n leak s an[...]

H6143 16 Ga. Finish Nailer -13 - H6143 PARTS BREAKDOWN                                               [...]

H6143 16 Ga. Finish Nailer -14 - H6143 PARTS LIST REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH6143001 SPECIAL CAP SCREW 48 PH6143048 PIN 2 PH6143002 AIR DEFLECTOR 49 PEC09M E-CLIP 6MM 3 PH6143003 BUMPER WASHER 50 PH6143050 DIRECTION PIN 4 PSB38M CAP SCREW M5-.8 X 25 51 PH6143051 DIRECTION STAND 5 PLW01M LOCK WASHER 5MM 52 PH6143052 ADJ. NUT 6[...]

H6143 16 Ga. Finish Nailer -15 - TROUBLESHOOTING Symptom Possible Cause Solution Air leaking at trig- ger valve area. 1. O-rings in trigger valve hous- ing are damaged. 1. O-rings must be replaced & operation of safety nose must be checked. Air leaking between housing and hose. 1. Loose screws in housing. 2. Damaged O-ring. 3. Loose air fitting[...]

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warr[...]

WARRANTY CARD Name _________________________________________________________________ Street _________________________________________________________________ City _______________________ State _________________________ Zip _________ Phone # ____________________ Email ________________________ Invoice # _____ Model # ____________________ Order # ____[...]

FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here[...]