Grizzly H2911 инструкция обслуживания

COPYRIGHT © JANUARY, 2002 BY GRIZZLY INDUSTRIAL, INC. 1821 VALENCIA ST., BELLINGHAM, WA 98227 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. PRINTED IN TAIWAN 18 GAUGE BRAD NAILER MODEL H2911 INSTRUCTION MANUAL[...]

For Your Own Safety Read Instruction Manual Before Operating This Equipment Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. Indicates a potentially hazardous situation which, if not a[...]

H2911 18 Gauge Brad Nailer -2 - 10. USE PROPER EXTENSION CORD for the tool. Make sure your extension cord is in good condition. Conductor size should be in accordance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheat[...]

H2911 18 Gauge Brad Nailer -3 - Operating this nailer can propel objects into the air, causing immedi- ate eye damage. To protect yourself, always wear American National Standards Institute (ANSI) approved safety glasses or goggles when oper- ating this equipment. In addition, this nailer discharges at 85-90 decibels. To protect your hearing, alway[...]

H2911 18 Gauge Brad Nailer -4 - INTRODUCTION Commentary Most importantly, we stand behind our tools. If you have any service questions or parts requests, please call or write us at the location listed below. Grizzly Industrial, Inc. 1203 Lycoming Mall Circle Muncy, PA 17756 Phone: (570) 546-9663 Fax: (800) 438-5901 E-Mail: techsupport@grizzly.com W[...]

H2911 18 Gauge Brad Nailer -5 - Compressed Air System Safety Yoke Mechanism The safety yoke is a mechanical device that can fail. Never rely on the safety yoke mechanism as an excuse to point the nailer at yourself or any bystanders. Serious injury may occur. Exceeding the maximum permissible operating pressure may cause the nailer to explode, blow[...]

H2911 18 Gauge Brad Nailer -6 - OPERATION Loading Nailer Operating Nailer To load your nailer: 1. Disconnect the air supply from the nailer! 2. Push the magazine latch in the direc- tion shown in Figure 1 . If you have not read the safety instruc- tions in this manual, do not operate the nailer. Before you operate your nailer, place one drop of the[...]

H2911 18 Gauge Brad Nailer -7 - Cleaning Nailer Oiling Nailer Special oil has been included with your new Grizzly nailer to help maintain its use- ful life. Place one drop of oil in the nailer air inlet (as shown in Figure 4 ) before every use. Wipe off any excess oil near the nail- er exhaust to avoid dust build-up. When the oil that was included [...]

Always disconnect air from nailer whenever clearing a jammed nail! H2911 18 Gauge Brad Nailer -8 - 4. The jammed nail should now be visi- ble; remove it with needle nose pliers. 5. Install the guide cover and check the safety yoke mechanism for proper operation (following the same instruc- tions as mentioned in the Safety sec- tion). Figure 5. Remo[...]

H2911 18 Gauge Brad Nailer -9 - Replacing Pistons/O-Rings If you use your nailer day in and day out, Grizzly offers repair pistons as cheap insurance against wasted down time and lost profits in the event that a piston or pis- ton shaft becomes worn out. To replace a piston: Figure 7. Removing rear cap. 6. Remove the guide cover from the nose assem[...]

H2911 18 Gauge Brad Nailer -10 - H2911 PART BREAKDOWN[...]

H2911 18 Gauge Brad Nailer -11 - 01 PH2911001 UM HD BOLT 02 PH2911002 CAP COVER 03 PH2911003 SEAL 04 PH2911004 CAP SCREW 05 PH2911005 SETSCREW 06 PH2911006 CAP 07 PH2911007 PISTON STOPPER 08 PH2911008 O-RING 09 PH2911009 COLLAR 10 PH2911010 O-RING 11 PH2911011 SPRING 12 PH2911012 PISTON HEAD VALVE 13 PH2911013 O-RING 14 PH2911014 O-RING 15 PH291101[...]

TROUBLESHOOTING Air leaking at trigger valve area. Air leaking between hous- ing and hose. Air leaking between hous- ing and cap assembly. Tool skips nails while dis- charging. Tool runs slowly or has a loss of power. Fasteners frequently jam the nailer. Nailer does not fire. 1. O-rings must be replaced & operation of safety yoke must be checke[...]

H2911 18 Gauge Brad Nailer -13 - Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance. This is Grizzly’s sole wr[...]

Name __________________________________________________________ Street __________________________________________________________ City ____________________ State ________ Zip _________ Phone Number ____________ E-Mail ___________________ FAX ____________ Model # ___________________________ Order # _______________________ The following information i[...]

FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here[...]