Grizzly G9962Z инструкция обслуживания

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80

Идти на страницу of

Хорошее руководство по эксплуатации

Законодательство обязывает продавца передать покупателю, вместе с товаром, руководство по эксплуатации Grizzly G9962Z. Отсутствие инструкции либо неправильная информация, переданная потребителю, составляют основание для рекламации в связи с несоответствием устройства с договором. В законодательстве допускается предоставлении руководства в другой, чем бумажная форме, что, в последнее время, часто используется, предоставляя графическую или электронную форму инструкции Grizzly G9962Z или обучающее видео для пользователей. Условием остается четкая и понятная форма.

Что такое руководство?

Слово происходит от латинского "instructio", тоесть привести в порядок. Следовательно в инструкции Grizzly G9962Z можно найти описание этапов поведения. Цель инструкции заключается в облегчении запуска, использования оборудования либо выполнения определенной деятельности. Инструкция является набором информации о предмете/услуге, подсказкой.

К сожалению немного пользователей находит время для чтения инструкций Grizzly G9962Z, и хорошая инструкция позволяет не только узнать ряд дополнительных функций приобретенного устройства, но и позволяет избежать возникновения большинства поломок.

Из чего должно состоять идеальное руководство по эксплуатации?

Прежде всего в инструкции Grizzly G9962Z должна находится:
- информация относительно технических данных устройства Grizzly G9962Z
- название производителя и год производства оборудования Grizzly G9962Z
- правила обслуживания, настройки и ухода за оборудованием Grizzly G9962Z
- знаки безопасности и сертификаты, подтверждающие соответствие стандартам

Почему мы не читаем инструкций?

Как правило из-за нехватки времени и уверенности в отдельных функциональностях приобретенных устройств. К сожалению само подсоединение и запуск Grizzly G9962Z это слишком мало. Инструкция заключает ряд отдельных указаний, касающихся функциональности, принципов безопасности, способов ухода (даже то, какие средства стоит использовать), возможных поломок Grizzly G9962Z и способов решения проблем, возникающих во время использования. И наконец то, в инструкции можно найти адресные данные сайта Grizzly, в случае отсутствия эффективности предлагаемых решений. Сейчас очень большой популярностью пользуются инструкции в форме интересных анимаций или видео материалов, которое лучше, чем брошюра воспринимаются пользователем. Такой вид инструкции позволяет пользователю просмотреть весь фильм, не пропуская спецификацию и сложные технические описания Grizzly G9962Z, как это часто бывает в случае бумажной версии.

Почему стоит читать инструкции?

Прежде всего здесь мы найдем ответы касательно конструкции, возможностей устройства Grizzly G9962Z, использования отдельных аксессуаров и ряд информации, позволяющей вполне использовать все функции и упрощения.

После удачной покупки оборудования/устройства стоит посвятить несколько минут для ознакомления с каждой частью инструкции Grizzly G9962Z. Сейчас их старательно готовят или переводят, чтобы они были не только понятными для пользователя, но и чтобы выполняли свою основную информационно-поддерживающую функцию.

Содержание руководства

  • Страница 1

    MODEL G0445/G0582/G9962Z/9962ZX 2 4 " W I D E - B E L T S A N D E R COPYRIGHT © OCTOBER 2005 BY GRIZZLY INDUSTRIAL, INC. REVISED JUNE 2006. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #CR 7521 PRINTED IN TAIWAN INSTRUCTION MANUAL[...]

  • Страница 2

    WARNING Some dust created by power sanding, sawing, grind- ing, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks, cement, and other masonr[...]

  • Страница 3

    T able of Con ten ts INTRODUCTION ............................................................................................................................... 3 Foreword .................................................................................................................................... 3 Contact Info .............................[...]

  • Страница 4

    -2- G0445/G0582/G9962Z/9962ZX Wide Belt Sander Oscillation Timing .................................................................................................................... 30 Oscillation Speed ..................................................................................................................... 32 Table Parallelism .......[...]

  • Страница 5

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -3- If you have any comments regarding this manual, please write to us at the address below: Grizzly Industrial, Inc. C / O Technical Documentation Manager P.O. Box 2069 Bellingham, WA 98227-2069 We stand behind our machines. If you have any service questions or parts requests, please call or write us at t[...]

  • Страница 6

    -4- G0445/G0582/G9962Z/9962ZX Wide Belt Sander Con trol P anel F eat ures Ex ter na l Fea tu res A. Digital Amp Draw Meter B. Table-Height Digital Readout C. Table Up Key D. Table Down Key E. Sanding Belt Start Button F. Conveyor Belt Start Button G. Power Light H. Table Set (Enter) Key I. Table Adjustment Start Key J. Table Adjustment Stop Key K. [...]

  • Страница 7

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -5- In ter nal Feat ures A. Belt Tension Knob B. Platen Adjustment Lever C. Platen Adjustment Lock Lever D. Lock Post Release Lever E. Tracking Adjustment Knob Figure 4. Inside the left access door. F. Upper Roller G. Airflow Adjustment Knob H. Speed Control Adjustment Knob I. Air Fork and Air Jet J. Diaph[...]

  • Страница 8

    -6- G0445/G0582/G9962Z/9962ZX Wide Belt Sander Mach ine Da ta Sheet ( G 0 4 4 5 )[...]

  • Страница 9

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -7- Mach ine Da ta Sheet ( G 0 582 )   ?[...]

  • Страница 10

    -8- G0445/G0582/G9962Z/9962ZX Wide Belt Sander Mach ine Da ta Sheet ( G9 9 62Z )[...]

  • Страница 11

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -9- Mach ine Da ta Sheet ( G9 9 62Z X )   ?[...]

  • Страница 12

    -10- G0445/G0582/G9962Z/9962ZX Wide Belt Sander 4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing damage. 5. WEAR PROPER APPAREL. D O NO T wear loose clothing, gloves, neckties, rings, or jewelry which may get caught in moving parts. Wear protective hair covering to con - tain long hair and wear [...]

  • Страница 13

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -11- 7. ONLY ALLOW TRAINED AND PROP- ERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make sure operation instructions are safe and clearly understood. 8. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visitors a safe dis- tance from the work area. 9. MAKE WORKSHOP CHILD PROOF. Use padlocks, master [...]

  • Страница 14

    -12- G0445/G0582/G9962Z/9962ZX Wide Belt Sander A ddit io nal S af et y f or Wi de Belt San ders 1. INFEED/OUTFEED AREA. When feeding the workpiece into the machine, keep clear of kickback path. 2. WORKPIECE FEEDING. Never force the workpiece into the sander, and feed only one workpiece at a time. 3. CLOTHING. Roll up or button sleeves, tie all loo[...]

  • Страница 15

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -13- The following list outlines the electrical phase and voltage required to operate the various sander models, as well as the amperage draw of their motors. Note: If you do not have three-phase power available, you will have to install a phase converter such as the Griz zly Phase Converter. Amperage Draw[...]

  • Страница 16

    -14- G0445/G0582/G9962Z/9962ZX Wide Belt Sander 4 40 V Con necti on To wire the sander to 440V: 1. DISCONNECT THE SANDER FROM THE POWER SOURCE! 2. Open the electrical box located on the back of the machine. 3. On the transformer, remove the wire labeled " 1 " connected to the 220V terminal for your model of sander, and connect it to the 4[...]

  • Страница 17

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -15- Si te Con sidera tio ns Fl oor Loa d Refe r to the Ma chine Data S hee t for the weight and footprint spec ifications of your machine. So me shop flo ors may require additi onal reinforcement to sup por t both the machine and o perato r . Wo rki ng Cle ar anc e Working clearances can be thought of as [...]

  • Страница 18

    -16- G0445/G0582/G9962Z/9962ZX Wide Belt Sander To install the air line: 1. Connect the hose from your air compressor to the air inlet ( Figure 9 ) on the regulator. Air Inlet Air ON/OFF Lever (Open Position) Regulator Knob 2. Move the red handle on the regulator to the open position (parallel with the air inlet). 3. Lift the regulator knob ( Figur[...]

  • Страница 19

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -17- Figure 11. Regulator knob. Dus t Col lectio n Figure 12. Typical three-port configuration. An efficient and clean dust collection system is essential to the proper function of the sander. Ensuring a healthy work environment is also dependent upon cleaning and maintaining your dust collection system. F[...]

  • Страница 20

    -18- G0445/G0582/G9962Z/9962ZX Wide Belt Sander To install the sanding belt: 1. DISCONNECT THE SANDER FROM THE POWER SOURCE! 2. De-activate the belt tension piston by turning the belt tension knob ( Figure 13 ). 3. Remove the lock post release lever ( Figure 13 ) by turning it counterclockwise 1 ⁄ 2 turn and pulling it up and out of the mounting [...]

  • Страница 21

    P ress ure Ro l ler T est It is absolutely essential to keep the pres- sure rollers set below the level of the sand - ing roller. If the pressure rollers are even, or higher than the sanding roller, the wood WILL be propelled from the sander at a high rate of speed. This situation could cause serious kick-back injury. To check the pressure roller h[...]

  • Страница 22

    -20- G0445/G0582/G9962Z/9962ZX Wide Belt Sander Reco mmen ded A dj ust ments For your convenience, the adjustments listed below have been performed at the factory and require no further adjustment. However, we rec - ommend that you verify that the adjustments are correct and to your satisfaction. Recommended adjustment checklist: — Table Calibrat[...]

  • Страница 23

    Ch oos in g Sandp aper Operati on Saf ety Your safety is important! Please follow the warnings below during this entire section: The grit you choose will depend on the type of work, the species of wood and the stage of finish - ing. Below is a chart that groups abrasives into different categories and shows which grits fall into each-one. We recomme[...]

  • Страница 24

    -22- G0445/G0582/G9962Z/9962ZX Wide Belt Sander T able Mo ve ment Table height can be adjusted manually or with the digital key pad and motor (see Figure 15 ). Manual Table Movement: Turn the handwheel located under the front of the infeed table for manual table positioning. Motorized Table Moveme nt: Press the TABLE UP or TABLE DOWN key once for m[...]

  • Страница 25

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -23- Am p Dra w Meter The amperage draw meter ( Figure 17 ) is located above the control panel. Use the meter to monitor the amperage draw on the machine while per- forming sanding operati ons. As a general rule, always start with a small load and work your way up. DO NOT work your machine to its maximum l[...]

  • Страница 26

    -24- G0445/G0582/G9962Z/9962ZX Wide Belt Sander Sand i ng W orkp iece Typically, no more than 0.5mm (approx. 1 ⁄ 64 ") of material is removed during each pass. Attempts to remove too much material can cause jamming, wood burning, rapid paper wear or tearing, poor finish, short motor life. Make sure that you mea - sure the workpiece thickness[...]

  • Страница 27

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -25- Figure 20. Sanding belt cleaning pad. H2845 Cleaning Pads Cleaning pads are the perfect accessory for wide belt sanders. Simply set the conveyor table to height and feed the pad through to “unload” a dirty sanding belt. Regular cleaning greatly increases the lifespan of sanding belts. Check with t[...]

  • Страница 28

    -26- G0445/G0582/G9962Z/9962ZX Wide Belt Sander Disconnect power to the machine when perform - ing maintenance, assem - bly or adjustments. Failure to do this may result in serious person - al injury. We ekl y Grease the grease fittings located on the feed belt roller axles and the sanding belt roller axles. They are identified with yellow labels. [...]

  • Страница 29

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -27- Figure 21. Water trap on the regulator. Dus t and W at er T ra ps There are two traps on this wide belt sander. One water trap is attached to the bottom of the air regulator, and the other trap is attached on the air diaphragm assembly. Cleaning is easy, with the system under air pressure, you can pus[...]

  • Страница 30

    -28- G0445/G0582/G9962Z/9962ZX Wide Belt Sander T able Cal i brat ion Use the first board fed through the sander to test the accuracy of the digital thickness gauge. To calibrate the digital thickness scale: 1. Using a properly set-up planer, plane a board to uniform thickness. 2. Lower the sander table far enough to place the planed board under th[...]

  • Страница 31

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -29- T ools N e ede d : Qt y 1 4mm O pen End Wr ench .................................. 1 Small Snap Ring Pliers ..................................... 1 6mm Hex W rench .............................................. 1 # 2 Phillips Sc rew driver ..................................... 1 Eventually the brake p[...]

  • Страница 32

    -30- G0445/G0582/G9962Z/9962ZX Wide Belt Sander Os ci l lat io n Ti mi n g When the oscillation is correctly adjusted, the sanding belt oscillates to the left and to the right at the same speed. If the sanding belt makes contact with a limit switch, as shown in Figure 25 , the emergency braking system will activate and stop the sander immediately. [...]

  • Страница 33

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -31- 5. Tighten the lock nut ( Figure 27 ) to secure the airflow adjustment knob. 6. Restrict the airflow across the air fork gap with a scrap piece of wood. You should notice the roller pivot to the right. When the stick is removed, the roller should pivot back to the left. 7. Test the oscillation by runn[...]

  • Страница 34

    -32- G0445/G0582/G9962Z/9962ZX Wide Belt Sander NOTICE The table has been adjusted at the fac- tory and should require no further attention. However, we recommend verifying that it is parallel with the sanding roller. The oscillation speed of the sanding belt is adjustable. Different oscillating speeds yield dif - ferent sanding results. We recomme[...]

  • Страница 35

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -33- To adjust the table parallelism: 1. Pass a 24" wide board through the sander until the entire surface of the board is mak- ing contact with the sanding belt. 2. Measure the thickness of the board at vari- ous points around the edge. 3. If there is a variation of thickness, the table can be adjust[...]

  • Страница 36

    -34- G0445/G0582/G9962Z/9962ZX Wide Belt Sander Figure 33. Pressure roller adjustment locations for platen and drum type sanders. 6. Loosen the roller lock nuts ( Figure 33 ) on the infeed pressure roller . Turn the adjust- ment studs ( Figure 33 ) to lower the pressure roller until it just touches the boar d. Note: DO NOT continue to lower the rol[...]

  • Страница 37

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -35- I. Oscillation Timing Piston and Diaphragm Assy. J. Oscillation Speed Control Piston K. Belt Tension Control Piston L. Belt Tension Control Switch M. Emergency Stop Button Switch N . Emergency Stop Push Brake Switch O. Left Belt Limit Switch P. Right Belt Limit Switch Q. Belt Tension Limit Switch R. E[...]

  • Страница 38

    -36- G0445/G0582/G9962Z/9962ZX Wide Belt Sander 7. Insert the 2x4' wooden studs under the table for support, and with help, lift the table slightly and move it out of the rear of the machine. 8. Disconnect the limit switch, remove all mount- ing screws, and remove the emergency stop push-panel assembly . 9. Turn both tracking adjustment bolts [...]

  • Страница 39

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -37-                    ?[...]

  • Страница 40

    -38- G0445/G0582/G9962Z/9962ZX Wide Belt Sander NOTICE Adjust the feed belt tension before adjusting the feed belt tracking. F e ed Belt T ens io n F e ed Belt T rac ki ng To adjust the feed belt tracking: 1. Turn the feed belt ON . 2. If the feed belt is tracking to the right side of the table, turn the right adjustment bolt ( Figure 38 ) clockwis[...]

  • Страница 41

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -39- Maintenanc e Per formed Approximate H ours Of Use Mai nt ena nce Lo g Date[...]

  • Страница 42

    -40- G0445/G0582/G9962Z/9962ZX Wide Belt Sander T ro ubles hoo ti ng SYMPTOM Motor will not start. Motor will not start; fuses or circuit breakers blow. Motor overheats. Motor stalls (resulting in blown fuses or tripped cir - cuit). Machine slows when oper - ating. Loud, repetitious noise com - ing from machine. Machine is loud, overheats or bogs d[...]

  • Страница 43

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -41- T ro ubles hoo ti ng SYMPTOM Snake shaped marks on workpiece. Lines across width of work - piece. Glossy spots or streaks on workpiece. Sanding belt clogs quickly. Sanding belt does not ten - sion correctly; rollers pad under belt. Sanding belt runs off to one side, stopping the sander. Sanding belt w[...]

  • Страница 44

    -42- G0445/G0582/G9962Z/9962ZX Wide Belt Sander Control Panel Electrical Diagram (G0445/G0582/G9962Z/9962ZX)        [...]

  • Страница 45

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -43- Control Panel Component Locations (G0445/G0582/G9962Z/9962ZX) Sanding Belt STOP Button Conveyor Belt STOP Button Emergency Stop Button Sanding Belt START Button Conveyor Belt START Button Power Lamp Digital Amp Draw Meter Digital Panel[...]

  • Страница 46

    -44- G0445/G0582/G9962Z/9962ZX Wide Belt Sander                  [...]

  • Страница 47

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -45- Wiring Box Components (G0445/G0582/G9962ZX) Conveyor Motor Contactor Emergency Brake Contactor UP/DOWN Table Motor Contactors Conveyor Motor Overload Relay 220V Single- Phase Power Supply Junction Block Sanding Motor Contactor Sanding Motor Overload Relay Amp Meter Current Sensor 4 Amp Fuses[...]

  • Страница 48

    -46- G0445/G0582/G9962Z/9962ZX Wide Belt Sander L 1 L2 L 3 T1 T2 T3 98 9 7 95 9 6 21 N C 13 N O 14 N O 22 N C 1 2 3 4 5 6 NO N C 8 2 U V L 1 L 2 U3 1 6 1 7 1 8 1 9 1 2 1 1 6 5 3 2 1 4 1 5 14 22 A 2 T1 T2 T3 2 4 6 NC NO 2 0 2 1 97 98 95 9 6 N O N C 13 21 A 1 L L2 L 3 1 3 5 NO N C R S 1 1 U1 V1 3 9 T1 T2 T3 2 4 6 T1 T2 T3 2 4 6 S R S 14 22 A 2 T1 T2 [...]

  • Страница 49

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -47- Wiring Box Components (G9962Z) Transformer Sanding Motor Contactor Conveyor Motor Contactor Amp Meter Current Sensor Emergency Brake Contactor UP/DOWN Table Motor Contactors Sanding Motor Overload Relay Conveyor Motor Overload Relay Two 4 Amp Fuses 220V/440V Three-Phase Power Supply Junction Block[...]

  • Страница 50

    -48- G0445/G0582/G9962Z/9962ZX Wide Belt Sander M 1 R U S V 3 A W L 1 2 S O L 1 3 F R 2 0 2 1 R F 1 7 1 9 1 6 1 8 L S L S L S 1 O L 1 M1 G L S TO P S TA R T M1 8 9 7 6 A 5 L S 2 L S 3 L S 4 P O WE R S O UR CE BR AKE T A B L E L I F T I N G & LO W E RI N G R U S V U V 3 2 S A NDI N G B E L T CONV E Y OR B E L T R Em e rg e nc y S t o p S A NDI N[...]

  • Страница 51

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -49- MO TO R M1 R U S V 3 A W L 1 2 SO L 1 3 F R 2 0 2 1 R F 1 7 1 9 1 6 1 8 L S L S L S 1 L S 2 L S 3 L S 4 O L 1 M 1 GL ST OP ST AR T M 1 9 7 6 A 5 P OWE R S OU R C E B R A K E T A B L E L I F T I N G & L O W E R I N G MO TO R R U S V U V 3 2 S A N D I N G B E L T C O N V E Y O R B E L T E m e r g e [...]

  • Страница 52

    -50- G0445/G0582/G9962Z/9962ZX Wide Belt Sander 1 2 4 7 3 13 9 8 6 5 12 11 10 T o ol Bo x and A ccess or ies Diag ram[...]

  • Страница 53

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -51- T o ol Bo x and A ccess or ies Pa r ts Li st REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH29330001 PLATEN REMOVAL TOOL 7 P0582007 SANDING BELT (#100, 75" LONG) (G0445/G0582) (G0445/G0582) 2 P9962Z0002 LIMIT SWITCH ROD 7 P0582009 SANDING BELT (#180, 75" LONG) 3 P9962Z0003 TOOL BOX (G0445[...]

  • Страница 54

    -52- G0445/G0582/G9962Z/9962ZX Wide Belt Sander   Sand i ng Mot or Sy st em Dia gra m[...]

  • Страница 55

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -53- REF PART # DESCRIPTION REF PART # DESCRIPTION 1101 P9962Z1101 MACHINE FRAME 1121 P9962Z1121 BRAKE BRACKET 1102 P9962Z1102 MOTOR BASE 1122 PW02 FLAT WASHER 3/8 1103 P9962Z1103 MOTOR BASE HINGE 1123 PB21 HEX BOLT 3/8-16 x 3/4 1104 PN13 HEX NUT 1/2-13 1124 P9962Z1124 TABLE LIFTING COLLAR 1105 P9962Z1105 [...]

  • Страница 56

    -54- G0445/G0582/G9962Z/9962ZX Wide Belt Sander T able Li f t Sy st em Dia gra m[...]

  • Страница 57

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -55- T able Li f t Sy st em P ar ts L is t REF PART # DESCRIPTION REF PART # DESCRIPTION 2101 P9962Z2101 ELEVATION SCREW 2321 P9962Z2321 HANDWHEEL 2102 PB03 HEX BOLT 5/16-18 X 1 2322 P9962Z2322 MOTOR BASE 2103 PW07 FLAT WASHER 5/16 2323 PB31 HEX BOLT 1/4-20 X 1 2104 PLW01 LOCK WASHER 5/16 2324 PLW02 LOCK W[...]

  • Страница 58

    -56- G0445/G0582/G9962Z/9962ZX Wide Belt Sander Con v e y or Sy stem Diag ram[...]

  • Страница 59

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -57- Con v e y or Sy stem Pa r ts Li st REF PART # DESCRIPTION REF PART # DESCRIPTION 3101 P9962Z3101 CONVEYOR TABLE 3123-2 P9962ZX3123-2 FAN COVER 3102 P9962Z3102 CONVEYOR BELT (G9962ZX/G0582/G0445) 3103 P9962Z3103 GEARBOX FIX PLATE 3124 PLW06M LOCK WASHER 10MM 3104 P9962Z3104 CUSHION 3126 P9962Z3126 TIMI[...]

  • Страница 60

    -58- G0445/G0582/G9962Z/9962ZX Wide Belt Sander                        [...]

  • Страница 61

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -59- F e ed, Dru m, and P ressu re R ol ler P ar ts L is t REF PART # DESCRIPTION REF PART # DESCRIPTION 4101 P05824101 PISTON SLIDE RAIL (G0582) 4205 PSS07 SETSCREW 1/4-20 X 1/2 4102 P05824102 PISTON BRACKET (G0582) 4301 P9962Z4301 PISTON ROD 4103 P9962Z4103 COMPRESSION SPRING (G9962Z/G9962ZX/G0445) 4104 [...]

  • Страница 62

    -60- G0445/G0582/G9962Z/9962ZX Wide Belt Sander                        [...]

  • Страница 63

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -61- Sand i ng D r um, a nd P laten Sy st em P ar ts L is t REF PART # DESCRIPTION REF PART # DESCRIPTION 5104 P9962Z5104 BEARING UCC206 5314 P05825314 BRACKET SHAFT (G0582/G0445) 5107 PK11 KEY 5/16 X 5/16 X 1-3/16 5315 PSB16 CAP SCREW 3/8-16 X 3/4 5108 PLW01 LOCK WASHER 5/16 (G0582/G0445) 5110 PLW07 LOCK [...]

  • Страница 64

    -62- G0445/G0582/G9962Z/9962ZX Wide Belt Sander                       ?[...]

  • Страница 65

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -63- Upper Ro l ler Sy stem Pa r ts Li st REF PART # DESCRIPTION REF PART # DESCRIPTION 6101 P04456101 SQUARE FRAME (G0445) 6132 PB07 HEX BOLT 5/16-18 X 3/4 6101 P9962Z6101 SQUARE FRAME 6133 PS08 PHLP HD SCR 10-24 X 3/4 (G9962Z/G9962ZX/G0582) 6134 PN07 HEX NUT #10-24 6103 P04456103 FRAME SEAL (RIGHT) (G044[...]

  • Страница 66

    -64- G0445/G0582/G9962Z/9962ZX Wide Belt Sander Cab ine t As semb ly Diag ram[...]

  • Страница 67

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -65- Cab ine t As semb ly Pa r ts Li st REF PART # DESCRIPTION REF PART # DESCRIPTION 7101 P9962Z7101 UPPER FRAME COVER 7105 P9962Z7105 RIGHT DOOR, UPPER FRAME (G9962Z/G9962ZX) (G9962Z/G9962ZX) 7101 P04457101 UPPER FRAME COVER (G0445) 7105 P05827105 RIGHT DOOR, UPPER FRAME 7101 P05827101 UPPER FRAME COVER [...]

  • Страница 68

    -66- G0445/G0582/G9962Z/9962ZX Wide Belt Sander G9962Z G9962ZX G0445 G0582 8104 8107 8133 8113 8116 8106 8128-1 8109 8117 8111 8132 8115 8112, 220V 8118 8129-1 8110 8129-2 8131 8108 8128-2 8130 8121 8120 8119 8123 8122 8122 8124 8103 8102 8101 8126A 8114, 220V 8135, 440V 8136, 440V 8105 8104 8113 8116 8106 8109 8117 8132 8115 8112 8118 8114 8105 81[...]

  • Страница 69

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -67- REF PART # DESCRIPTION REF PART # DESCRIPTION 8101 P9962Z8101 ELECTRICAL CONTROL BOX 8114 P9962ZX8114 OVRLD RELAY LR3D-086 220V 8102 P9962Z8102 HINGE (2.5-4A SET TO 3.4A) 8103 P9962Z8103 CONTROL BOX DOOR (G0445/G9962ZX/G0582) 8104 P9962Z8104 BASE PLATE 8115 P9962Z8115 CONTACTOR LC1-D096 8105 PN05 HEX [...]

  • Страница 70

    -68- G0445/G0582/G9962Z/9962ZX Wide Belt Sander                        [...]

  • Страница 71

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -69- Belt Osc il lati on Sy st em P ar ts L ist REF PART # DESCRIPTION REF PART # DESCRIPTION 9101 P9962Z9101 FILTER CUP 9121 P9962Z9121 CONNECTOR 1/4N X 1/8T 9102 P9962Z9102 PRESSURE REGULATOR 9122 P9962Z9122 AIR SWITCH 9103 P9962Z9103 BRONZE CONNECTOR 9123 P9962Z9123 CONNECTOR 1/4N X 1/8T 9105 P9962Z9105[...]

  • Страница 72

    -70- G0445/G0582/G9962Z/9962ZX Wide Belt Sander Lab el Dia gram Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Gri[...]

  • Страница 73

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -71- REF PART # DESCRIPTION REF PART # DESCRIPTION 200 P9962Z200 LABEL (MODEL G9962Z) 211 P9962ZX211 LABEL (AMP LOAD FOR G9962ZX) 200 P9962ZX200 LABEL (MODEL G9962ZX) 211 P0582211 LABEL (AMP LOAD FOR G0582) 200 P0582200 LABEL (MODEL G0582) 211 P0445211 LABEL (AMP LOAD FOR G0445) 200 P0445200 LABEL (MODEL G[...]

  • Страница 74

    -72- G0445/G0582/G9962Z/9962ZX Wide Belt Sander Hard w are Reco gn iti on C har t[...]

  • Страница 75

    G0445/G0582/G9962Z/9962ZX Wide Belt Sander -73- Not es[...]

  • Страница 76

    -74- G0445/G0582/G9962Z/9962ZX Wide Belt Sander Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzl[...]

  • Страница 77

    CUT ALONG DOT TED LINE Name _____________________________________________________________________________ Street _____________________________________________________________________________ City _______________________ State _________________________ Zip _____________________ Phone # ____________________ Email ________________________ Invoice # __[...]

  • Страница 78

                                  ?[...]

  • Страница 79

    [...]

  • Страница 80

    Buy Direct and Save with Grizzly ® – Trusted, Proven and a Great Value! -OR- • SECURE ORDERING • ORDERS SHIPPED WITHIN 24 HOURS • E-MAIL RESPONSE WITHIN ONE HOUR Visit Our Website Today And Discover Why Grizzly ® Is The Industry Leader! Call Today For A FREE Full Color Catalog[...]