Grizzly G9922 инструкция обслуживания

OSCILLATING SPINDLE SANDER MODEL G9922 INSTRUCTION MANUAL COPYRIGHT © 2000 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. PRINTED IN CHINA.[...]

-B- G9922 Oscillating Spindle Sander[...]

G9922 Oscillating Spindle Sander -1- Table Of Contents PAGE 1. SAFETY SAFETY RULES FOR ALL TOOLS ......................................................................2-3 ADDITIONAL SAFETY INSTRUCTIONS FOR SANDERS ......................................4 2. CIRCUIT REQUIREMENTS 110V OPERATION .........................................................[...]

-2- G9922 Oscillating Spindle Sander Safety Instructions For Power Tools SECTION 1: SAFETY 5. KEEP CHILDREN AND VISITORS AWAY . All children and visitors should be kept a safe distance from work area. 6. MAKE WORK SHOP CHILD PROOF with padlocks, master switches, or by removing starter keys. 7. DON’T FORCE TOOL . It will do the job better and safe[...]

G9922 Oscillating Spindle Sander -3- 9. USE PROPER EXTENSION CORD . Make sure your extension cord is in good condi- tion. Conductor size should be in accor- dance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.[...]

-4- G9922 Oscillating Spindle Sander Additional Safety Instructions For Sanders No list of safety guidelines can be com- plete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. Use this and other machinery with caution and respect. Failure to follow guidelines could result in se[...]

G9922 Oscillating Spindle Sander -5- 110V Operation SECTION 2: CIRCUIT REQUIREMENTS A 15-amp fuse or circuit breaker should be used when fusing this oscillating spindle sander. Circuits rated any higher are not adequate to pro- tect the wiring. Equipment returned to us for service that shows evidence of being over-fused will be repaired or replaced[...]

-6- G9922 Oscillating Spindle Sander We are proud to offer the Grizzly Model G9922 Oscillating Spindle Sander. The Model G9922 is part of a growing Grizzly family of fine wood- working machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitm[...]

G9922 Oscillating Spindle Sander -7- Unpacking This Oscillating Spindle Sander is shipped from the manufacturer in a carefully packed carton. If you discover the machine is damaged after you’ve signed for delivery, and the truck and dri- ver are gone, you will need to file a freight claim with the carrier. Save the containers and all pack- ing ma[...]

-8- G9922 Oscillating Spindle Sander Clean Up WORKING CLEARANCES Working clearances can be thought of as the dis- tances between machines and obstacles that allow safe operation of every machine without limitation. Ensure that your working area offers plenty of room for free movement and a substan- tial amount of distance between you and others tha[...]

G9922 Oscillating Spindle Sander -9- SECTION 4: ASSEMBLY Overview All die-cut metal parts have a sharp edge (called “flashing”) on them after they are formed. This is generally removed at the factory. Sometimes a bit of flashing might escape inspection, and the sharp edge may cause cuts or lacerations when handled. Please examine the edges of a[...]

-10- G9922 Oscillating Spindle Sander SECTION 5: Operations Before you put your oscillating spindle sander into use, give it a quick inspection. Before inspecting, ensure that the machine is switched off and disconnected from its power source. 1. Are all fasteners tight? 2. Is the sanding sleeve properly installed and secured? 3. Rotate the spindle[...]

G9922 Oscillating Spindle Sander -11- SECTION 6: MAINTENANCE General Shielded and pre-lubricated ball bearings require no lubrication. The working table and other non-painted sur- faces on the Model G9922 should be protected against rust and pitting. Some woodworkers rec- ommend using automotive paste wax on exposed steel and cast iron surfaces. If[...]

-12- G9922 Oscillating Spindle Sander The following pages contain general machine data, parts diagrams/lists, troubleshooting guide and Warranty/Return information for your Model G9922 Oscillating Spindle Sander. If you need parts or help in assembling your machine, or if you need operational information, we encourage you to call our Service Depart[...]

-13- G9922 Oscillating Spindle Sander GRIZZLY MODEL G9922 OSCILLATING SPINDLE SANDER Design Type .................................................................................................... Floor Model Overall Dimensions and Specifications: Table ...............................................................................................[...]

G9922 Oscillating Spindle Sander[...]

G9922 Oscillating Spindle Sander -15- REF PART # DESCRIPTION 01 G2902 Motor 02 P992202 Ground Ring Connector 03 P992203 Power Fork Connector 04 P992204 Plastic Connector Sleeve 05 P992205 Flat Key 06 P992206 Connection Plate 07 P992207 Worm Gear Shaft 08 P992208 Worm Gear 09 P992209 End Cover of Worm Gear 10 P992210 M5 x 10 Bolt 11 P992211 M5 x 25 [...]

-16- G9922 Oscillating Spindle Sander SYMPTOM Motor will not start. Motor will not start; fuses or circuit break- ers blow. Motor fails to develop full power (power out- put of motor decreas- es rapidly with decrease in voltage at motor terminals). Motor overheats. Motor stalls (resulting in blown fuses or tripped circuit). Machine slows down when [...]

G9922 Oscillating Spindle Sander -17- WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. Thi[...]

-18- G9922 Oscillating Spindle Sander NOTES[...]

G9922 Oscillating Spindle Sander -19- 10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8" Grinder ___5" - 8" Drill Press ___Mini Lathe ___8" Table Saw ___10" - 12" Thickness Planer ___8" - 10" Bandsaw ___Scroll Saw ___Disc/Belt Sander ___Spindle/Belt Sa[...]

FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 Place Stamp Here TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name_______________________________ Street_______________________________ City______________State______Zip______ Send a Grizzly Catalog to a friend:[...]