Grizzly G6050 инструкция обслуживания

COPYRIGHT © MAY, 2002 BY GRIZZLY INDUSTRIAL, INC. 1821 VALENCIA ST., BELLINGHAM, WA 98227 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. PRINTED IN TAIWAN ONLINE MANUAL DISCLAIMER THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS C[...]

For Your Own Safety Read Instruction Manual Before Operating This Equipment Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. Indicates a potentially hazardous situation which, if not a[...]

G6050 Round Head Framing Nailer Kit -2 - 10. USE PROPER AIR HOSE for the tool. Make sure your air hose is in good condition and is long enough to reach your work without stretching. 11. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neck- ties, rings, bracelets, or other jewel- ry which may get caught in moving parts. Non-slip footwear is[...]

G6050 Round Head Framing Nailer Kit -3 - Operating this nailer can propel objects into the air, causing immedi- ate eye damage. To protect yourself, always wear American National Standards Institute (ANSI) approved safety glasses or goggles when oper- ating this equipment. In addition, this nailer discharges at 85-90 decibels. To protect your heari[...]

G6050 Round Head Framing Nailer Kit -4 - INTRODUCTION Commentary Most important, we stand behind our tools. If you have any service questions or parts requests, please call or write us at the location listed below. Grizzly Industrial, Inc. 1203 Lycoming Mall Circle Muncy, PA 17756 Phone: (570) 546-9663 Fax: (800) 438-5901 E-Mail: techsupport@grizzl[...]

G6050 Round Head Framing Nailer Kit -5 - Compressed Air System Safety Yoke Mechanism The safety yoke is a mechanical device that can fail. Never rely on the safety yoke mechanism as an excuse to point the nailer at yourself or any bystanders. Serious injury may occur. Exceeding the maximum permissible operating pressure may cause the nailer to expl[...]

G6050 Round Head Framing Nailer Kit -6 - OPERATION Loading Nailer To load your nailer: 1. Disconnect the air supply from the nailer! 2. Pull the magazine pusher all the way back until it locks in place. 3. Place a stick of nails into the maga- zine as shown in Figure 1 . Make sure the pointed ends of the nails are fac- ing down. 3. Slide the stick [...]

G6050 Round Head Framing Nailer Kit -7 - Operating Nailer Adjusting Depth Besides damaging your workpiece, deflection can cause injury if your free hand is securing the workpiece in the location that the nail deflects. 4. Press the trigger. If the nail drove into the wood far enough, continue with your intended operations. If the nail either went t[...]

G6050 Round Head Framing Nailer Kit -8 - Always disconnect air from nailer whenever clearing a jammed nail! Clearing Jammed Nails The most frequent situation with any type of nailer is a nail jam. A jammed nail must be cleared before using the nailer again. The two places where a nail can get jammed are the magazine and the dis- charge area. To cle[...]

G6050 Round Head Framing Nailer Kit -9 - Cleaning Nailer Use a good solvent to clean the nose assembly of the nailer. Always be sure that the nailer is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body of the nail- er; this may result in leaks and damage to the nailer and the air fittings. Neve[...]

G6050 Round Head Framing Nailer Kit -10 - Replacing Pistons/O-Rings If you use your nailer day in and day out, Grizzly offers repair pistons as cheap insurance against wasted down time and lost profits in the event that a piston or pis- ton shaft becomes worn out. To replace a piston: Figure 7. Removing nailer exhaust cap. 8. With a long flathead s[...]

G6050 Round Head Framing Nailer Kit -11 - G6050 PART BREAKDOWN 25 1 2 1 4 1 3 11 1 0 9 8 59 26 6 5A 4 2A 7A 89 1A 24 30A 29 28A 82 80A 39 73 83A 74A 82 68A 28 A 88 27 31A 35A 65 85 6 7 A 8 5 61 A 66 3 9 92 90 39 23 22 19 2 1A 20 16B 15-2 15A 36 39 69 53A 52 51 50 49 48 47 46 45 42 43 44 41 37 A 40 9 5 84 30A 71A 56 56 6 2 63 64 21 - 1 12-1 58 60A 7[...]

G6050 Round Head Framing Nailer Kit -12 - 01A P6048007A BUTTON HD CAP SCR 02A P6050002A EXHAUST COVER 04 P6050004 PU WASHER 05A P6050005A CAP SCREW + SW 06 P6050006 CAP 07A P6044077 FLAT WASHER 08 P6050008 SPACER 09 P6050009 PISTON STOPPER 10 P6050010 SPRING 11 P6050011 O-RING 12 P6050012 PISTON HEAD VALVE 12-1 P6050012-1 SPACER 13 P6050013 O-RING [...]

TROUBLESHOOTING Air leaking at trigger valve area. Air leaking between hous- ing and hose. Air leaking between hous- ing and cap assembly. Tool skips nails while dis- charging. Tool runs slowly or has a loss of power. Fasteners frequently jam the nailer. Nailer does not fire. 1. O-rings must be replaced & operation of safety yoke must be checke[...]

G6050 Round Head Framing Nailer Kit -14 - Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance. This is Grizzly’[...]

Name __________________________________________________________ Street __________________________________________________________ City ____________________ State ________ Zip _________ Phone Number ____________ E-Mail ___________________ FAX ____________ Model # _______________Serial#________________ Order # ______________ The following information[...]

FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT NAIL Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here[...]