Grizzly G1061 инструкция обслуживания

BUFFING SYSTEM MODEL G1061/G1061Z INSTRUCTION MANUAL COPYRIGHT © 1992 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. JANUARY, 2002 PRINTED IN TAIWAN.[...]

WARNING Some dust created by power sanding, sawing, grind- ing, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks, cement, and other masonr[...]

Table Of Contents PAGE 1. SAFETY SAFETY RULES FOR POWER TOOLS ..............................................................2-3 ADDITIONAL SAFETY INSTRUCTIONS FOR BUFFERS ......................................4 2. CIRCUIT REQUIREMENTS 110V OPERATION ..................................................................................................5 [...]

-2- G1061/G1061Z Buffing System SECTION 1: SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. Indicates[...]

G1061/G1061Z Buffing System -3- 9. USE PROPER EXTENSION CORD . Make sure your extension cord is in good condi- tion. Conductor size should be in accor- dance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your[...]

-4- G1061/G1061Z Buffing System Additional Safety Instructions For Buffers 1. ALWAYS WEAR EYE PROTECTION! 2. WEAR AN APPROVED DUST MASK OR RESPIRATOR. Buffing operations produce dust. 3. MAKE SURE BUFFER IS SECURED FIRMLY TO A BENCH OR STAND BEFORE USE. Any “wobbles” must be corrected by shimming or blocking before operation. 4. DO NOT USE GRIN[...]

G1061/G1061Z Buffing System -5- 110V Operation SECTION 2: CIRCUIT REQUIREMENTS If you find it necessary to use an extension cord with the Model G1061/G1061Z, make sure the cord is rated Hard Service (grade S) or better. Refer to the chart in the standard safety instruc- tions to determine the minimum gauge for the extension cord. The extension cord[...]

-6- G1061/G1061Z Buffing System SECTION 3: INTRODUCTION We are proud to offer the Grizzly Model G1061/G1061Z Buffing System. The Model G1061/G1061Z is part of a growing Grizzly family of fine woodworking machinery. When used according to the guidelines set forth in this manu- al, you can expect years of trouble-free, enjoyable operation and proof o[...]

G1061/G1061Z Buffing System -7- Unpacking Piece Inventory NOTICE A full parts list and breakdown can be found toward the end of this manual. For easier assembly, or to identify specific parts, please refer to the detailed illustrations at the end of the manual. After all the parts have been removed from the carton, you should have: • Buffing Unit[...]

-8- G1061/G1061Z Buffing System SECTION 6: OPERATIONS Keep loose clothing rolled up and out of the way of machinery and keep hair pulled back. Wear safety glasses dur- ing the entire operation process. Failure to com- ply may result in serious personal injury. Using this machine pro- duces sawdust which may cause allergic reactions and respiratory [...]

G1061/G1061Z Buffing System -9- Buffing & Polishing For buffing and polishing, Grizzly offers a broad line of buffing wheels and polishing compounds. Please refer to our current catalog. To buff or pol- ish: 1. Make sure the power cord is unplugged and remove the 1 3 ⁄ 8 " hex nuts at the end of each shaft. Facing the machine, the left-h[...]

-10- G1061/G1061Z Buffing System Accessory Removal To remove the buffing or sanding attachments, ensure that the switch is pushed in and the power cord is disconnected. With buffing wheels mount- ed, hold the shaft with one hand while loosening the nut with a wrench. If both shafts are con- cealed by sanding drums, use a wrench to loosen the desire[...]

G1061/G1061Z Buffing System -11- SECTION 7: MAINTENANCE Always be aware of the condition of your buffer. Routinely check the condition of the following items and repair or replace as necessary: • Loose mounting bolts • Worn switch • Worn or damaged cord • Worn or damaged support bearings or guide bearings Miscellaneous Shielded and pre-lubr[...]

-12- G1061/G1061Z Buffing System The following pages contain general machine data, parts diagrams/lists, a troubleshooting guide and Warranty/Return information for your Model G1061/G1061Z. If you need parts or help in assembling your machine, or if you need operational information, we encourage you to call our Service Department. Our trained servi[...]

G1061/G1061Z Buffing System -13- Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 MACHINE DATA SHEET Design Type .................................................................................................... Bench Model Overall Dimensions: Height ...................................................[...]

-14- G1061/G1061Z Buffing System Ref# Part# Description 001 P1061001 MOTOR BASE 002 P1061002 MOTOR CASE 003 PFH07 FLAT HD SCR 5 ⁄ 16 "-18 X 1 1 ⁄ 4 " 004 P1061004 STATOR (G1061) 004 P1061Z004 STATOR (G1061Z) 005 P1061005 ROTOR W/#6 (G1061) 005 P1061Z005 ROTOR (G1061Z) 007 P1061007 MOTOR FAN 008 P6206 BALL BEARING 6206ZZ 009 P1061009 E[...]

G1061/G1061Z Buffing System -15- NOTES:[...]

-16- G1061/G1061Z Buffing System Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole writ[...]

Name ____________________________________________________________________________________ Street ____________________________________________________________________________________ City ______________________________________________________________State________Zip_________ Phone Number_______________________E-Mail_______________________FAX________[...]

FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 Place Stamp Here TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name_______________________________ Street_______________________________ City______________State______Zip______ Send a Grizzly Catalog to a friend:[...]