Graco 3A1334E инструкция обслуживания

Instr uctions LD Series Oil and Grease Pump 3A1334E For dispensing non-cor rosive and non-abrasive lubricants, oil, grease, and automatic transmission fluids in stationary or mobile installations. Use with compressed air only . For prof essional use only . Not f or use with windshield washer fluid. List of models, incl uding Maximum Fluid Pressure:[...]

Oil Pump Models 2 3A1334E Oil Pump Models All oil models include a 2” npt(m) b ung adapter . PN Description Max air pressur e Max Fluid Pres sure Air inlet Fluid Inlet Fluid Outlet 3:1 PUMPS psi Mpa bar psi Mpa bar 24G576 Universal 150 1.03 10.3 750 5.17 51.7 1/4"-18 NPT 1"-11.5 NPT 1/2"-14 NPT 24G577 Universal 150 1.03 10.3 750 5.[...]

Grease Pump Models 3A1334E 3 Grease Pump Models PN Description Max air pressur e Max Fluid Pres sure Air inlet Fluid Inlet Fluid Outlet 50:1 PUMPS psi Mpa bar psi Mpa bar 24G600 16kg (35lb) 150 1.03 10.3 7500 51.7 517 1/4"-18 Npt Priming piston 1/4"-18 Npt 24G601 16kg (35lb) 150 1.03 10.3 7500 51.7 517 1/4"-19 BSPP Priming piston 1/4[...]

Warnings 4 3A1334E Wa r n i n g s The f ollowing w ar nings are f or the setup , use, groundin g, maintenance, and rep air of this equipment. The e xclama- tion point symbol ale r ts you to a gener al warning and the hazard symbols ref er to procedure-specific risks. When these symbols appear in the body of this manual , ref er ba ck to these W arn[...]

Warnings 3A1334E 5 EQUIPMENT MISUSE HAZARD Misuse can cause de ath or serious injur y . • Do not operate the unit when f atigued or under the influ ence of drugs or alcohol. • Do not exceed the ma ximum working pressure or temperature rating of the lo west r ated system component. See T echnical Data in all equipment man uals. • Use fluids an[...]

Installation 6 3A1334E Installation NO TE: Ref erence letters and n umbers in parentheses in the te xt refer to callouts in the fig ures and dra wings. Gr ounding Ground all e quipment: • Pump: Use a ground wire and clamp as shown in F IG . 1. a. Remov e the ground scre w (Z) and inser t through the e ye of the ring terminal at end of ground wire[...]

Installation 3A1334E 7 T ypical Installation The typical installation shown in F IG . 2 is only an installation guide . It is not an actual system design. Cont act your Graco Distributor f or assistance in des igning a system to suit your needs. Stationary Mountings Key (F IG . 2) A Fluid outlet line (fl e xible connection required) BP u m p C Grou[...]

Installation 8 3A1334E Installation Guidelines Reference letters f ound in the follo wing instr uctions, ref er to T ypical Installation diagram pro vided on page 7. • A ball v alv e must be installed upstr eam of the reg u- lator (G). • The fluid outlet line (A), fluid inlet line (L) and air inlet line (M) must be fle xible (such as a hose). N[...]

Installation 3A1334E 9 Air Line and Accessories NO TE: Install the air line accessories in the order sho wn in the T y pical Installation on page 7. • Use thread sealant on all male threads exce p t s wivel co nnections. • Install a pump runaw a y valv e (D) to shut off the air to the pump if the pum p accelerates be yond the pre-adjusted setti[...]

Operation 10 3A1334E Operation Thermal Induced Pressure Relief (Oil pumps onl y) Thermal Relief Theory of Operation The pump oper ation is similar to most doub le acting reciprocating pumps . The pump only comes to a com- plete stop on the up st roke . The pump will stroke through on the down strok e due to the inlet check re lief passage. Excess p[...]

Operation 3A1334E 11 Install only one pump pe r delivery system. Do not use the pumps in a paralle l pump installation. Loss of pump prime can occur if all the f ollowing e vent s occur in sequence: 1. A ther mal relief e vent occurs . 2. The air supply v alve is closed. 3. A dispen se valv e located at an ele vation higher than the tank le vel, is[...]

Operation 12 3A1334E Step 6 is for Oil Pumps Only: 6. The thermal relief f eature of this oil pump can increase t he amount of t ime needed to fully prime the pump when compared t o pumps without a ther- mal relief feature. T o m inimize this effect, prime th e pump before connect ing it to an alrea dy primed dis- tribution system. 7. Read and foll[...]

Operation 3A1334E 13 5. Examine f ollow plate to mak e sure r ubber gr ommet (c) is in place in center of the plate (F IG . 7). 6. Set follow plate on top of fres h grease (F IG . 8). Remov e air by pushing on the f ollow plate until the grease lev el is flush with the opening in the middle of the f ollow plate ( d). 7. Inser t pump drop tube thr o[...]

Repair 14 3A1334E Repair Replacing Pilot V alves Reference letters shown in the fo llowing instructions ref er to T ypical Installation dia gram, page 7. P ar t num- bers ref er to the P ar ts pages beginning on pag e 15. 1. Stop pump at the middle of its stroke. 2. Relie ve pr essure, page 11 . 3. Disconnect the air line (M). 4. Use a 10 mm soc ke[...]

Parts 3A1334E 15 Pa r t s 3:1 Oil Pump Models: 24G576 - 24G587: 5:1 Oil Pump Models: 24G588 - 24G599 Ref Part No Description Qty 2 116343 SCREW , ground 1 3 SCREW 3 4 SCREW M6 x 22 mm 5 5 ✠ O-RING, air piston 1 6 ✠ O-RING 1 7 ✠ O-RING 1 8 ✠ O-RING, 1 9 ✠ SEAL, u-cup 1 10 PIN, spring 1 11 ★ BALL, steel 1 12 BALL, steel 1 13 ✓ O-RING, ([...]

Parts 16 3A1334E Related Oil Pump Kits O-Ring Replacement Ki t - 24K293 f or 3:1 pumps; 24H855 f or 5:1 pumps (F IG . 11) NO TE: When replacing seals in the pu mp lower also ser vice the thro at and piston seals. Order repa ir kit 24H853. Instructions related to this kit are included in instru ction manual 3A1494 (includ ed with the kit). Throat an[...]

Parts 3A1334E 17 Kits P age 2 39 40 27 26 21 29 4 32 10 12 30 34 33 35 11 28 52, 53 or 54, Pa g e 15 5 14 13 20 3 17 6 20 7 22 9 8 36 18 19 15 51 50 21 31 T orque to 60 - 70 in lbs (6.8 - 7.9 N•m) 3 T orque to 25 - 35 in lbs (2.8 - 3.9 N•m) 4 T orque to 110 - 1 20 in lbs (12.4 - 13.6 N•m) 5 T orque to 80 - 90 in lbs (9.0 - 10.2 N•m) 6 T orq[...]

Parts 18 3A1334E 50:1 Grease Pump Models: 24G600 - 24G608 Ref Part No. Des cription Qty 2 116343 SCREW , ground 1 3 SCREW 3 4 SCREW , M6 X 22 mm 5 5 + O-RING, air piston 1 6 + O-RING (not shown) 1 7 + O-RING 10 8 +@ PIN, straight, slotted, 2.5x16 3 9 SCREW 1 10 @ O-RING 1 11 + SEAL, u-cup 1 12 + O-RING 3 13 W ASHER,M8 1 14 CO VER, b ottom, machinin[...]

Parts 3A1334E 19 Related Grease Pump Kits Throat and Piston Seal Replacement Kit - 24H854 (F IG . 13) Instructions related to this kit are included in instruction manual 3 A1495 (included wit h the kit). O-Ring and Seal Replacem ent Kit - 24H856 (F IG . 14) Instructions related to this ki t ar e included in instr uction manual 3A1495 (in cluded wit[...]

Parts 20 3A1334E 41 42 21 Kits , page 15 3 2 8 8 34 27 4 14 20 5 13 38 37 11 31 30 25 6 12 33 36 32 26 24 23 28 10 29 35 19 7 22 19 30 21 1 8 8 8 7 8 7 10 3 20 1 9 3 9 11 T orque to 60 - 70 in lbs (6.8 - 7.9 N•m) 3 T orque to 30 - 40 in lbs (3.4 - 4.5 N•m) 9 T orque to 70 - 80 in lbs (7. 9 - 9.0 N•m) 7 T orque to 45 - 55 ft lbs (61 - 75 N•m[...]

Parts 3A1334E 21 Oil or Grease Pump Air V alve Repair and Replacement Kits Instructions related to the f ollowing kits are included in instruction manua l 3A1496 (included with the kit). Replace Seals or Reb uild Air V alve Kits Air V alve Repair Kit - 24H798 , Air V alve Seal Kit - 24H851 and Air V alve End Ca p - 24H852. Air V alve Repair Kit - 2[...]

Parts 22 3A1334E Air V alve Replacement Kit - 24H848 (npt), 24H849 (bspp), 24H850 (bspt) (F IG . 18) Pilot V alve Replacem ent Kit - 24H749 This kit onl y includes the pilot v alves (20). If y ou also are repai ring/replacing the air valve (38/40) and air v alve seal (23/16) order the Air Motor Service Kit - 24J757 (npt ), 24J758 (bs pp) or 24J759 [...]

Troubleshooting 3A1334E 23 T r oubleshooting NO TE: Check all other possible problems and solutions bef ore disassemb ling the pump . Before you troub leshoot prob lems using the tab le below , relie ve the pressure and disconnect t he pump fluid line. If the pump starts when the air is tu r ned on again, the f luid line, dispensing v alve , etc. c[...]

Troubleshooting 24 3A1334E Intermittent air leakage coming from behind the air manifold. Pump con- tinues to function nor mally . Gasket is leaking Replace gask et. Low er air pressure to pre vent reoc- currence. Ther mal relief inlet chec k relief pas- sage in inlet housing is plugged Clear obstruction. Replace inlet filter . Continuou s air e xha[...]

Troubleshooting 3A1334E 25 Grease Models Pump f ails to operate Inadequate air supply pressu re or restricted air lines Increase air supp ly and/or clear restric tion. Closed or clogg ed pump valv es Open and/or clean . Clogged fluid line, hose , valv e, or other accessor y Relie ve pressure . Clear obstruction. Damaged air motor Assess dama ge, an[...]

Technica l Data 26 3A1334E T echnical Data 3:1 or 5:1 Oil Models † Calculated at a distance of 1 meter from measurements ta ken per ISO 96 14-2 @ 100 psi air pressure (6. 89 bar , 0.68 MP a) and 20 cycles per minutes. ‡ Measured per ISO 96 14-2 at 100 psi air pressure (6.89 ba r , 0.68 MP a) and 20 cycles per minute . * Muffler 11293 3 can be o[...]

Technical Data 3A1334E 27 Dimensions Model L inches (mm) O (Ov erall Length) inches (mm) Univ ersal Pump Only 6.9 (175) 16 (406) Multi* 42.4 (1076) 51.5 (1307) Drum 35.7 (907) 44.8 (1138) T ote 42.8 (108 7) 51.9 (1318) *Multi down tube is angle cut to the desired len gth as required 3/8” (10 m m) minimum L L Universal Pump Multi/Drum/T ote O O a [...]

Technica l Data 28 3A1334E P erformance Curve 3:1 Oil Model s 5:1 Oil Model s 0 10 (.3) 20 (.6) 30 (.8) 40 (1.1) 0 100 (6.9) 200 (13.8) 300 (20.7) 400 (27.6) 0 1 (3.8) 2 (7.6) 3 (11.4) 4 (15.1) 5 (18.9) 6 (22.7) 7 (26.5) 8 (30.3) 9 (34.1) 58 116 174 232 $LU)ORZVFIP PPLQ )OXLG)ORZJSP OSP &FOHVSHUP[...]

Technical Data 3A1334E 29 50:1 Grease Models † Calculated at a distance of 1 meter from measurements ta ken per ISO 96 14-2 @ 100 psi air pressure (6. 89 bar , 0.68 MP a) and 20 cycles per minutes. ‡ Measured per ISO 96 14-2 at 100 psi air pressure (6.89 ba r , 0.68 MP a) and 20 cycles per minute . * Muffler 11293 3 can be ordered separat ely f[...]

Technica l Data 30 3A1334E Dimensions 600 mm 945 mm 1145 mm 23.6 in. 37.2 in. 45.0 in. 400 pound drum 120 pound drum 35 pound drum 14.5 in. 370 mm 28.1 in. 715 mm 36.0 in. 915 mm a = 1/4 inch air inlet b = 1/4 inch fluid outlet c = 2 inch npt mounti ng configuration d = ground screw a d c b d a b c b a d c[...]

Notes 3A1334E 31 Notes[...]

All written and visual data con tained in th is document reflects the late st product information available at the time of pu blica tion. Graco reserves the right to make changes at any time without notice. Original instructions. T his manual contains English. MM 3A1334 Graco Headquarters: Minneapoli s Internationa l Offices: Belgium, China, Japan,[...]