Graco 24C728 B инструкция обслуживания

Instr uctions/P ar ts AIR DRIVEN Expanding Blade Mix er Expanding blade b ung-mounted ag itator f or maintaining suspension and even mixing in industrial paints and coatings. For prof essional use only . Not appr oved f or use in Eur ope an explosive atmosphere locations. Model 24C728, Series B Low Visco sity , up to 1000 centipoise Model 24C729, S[...]

Warnings 2 313643G W arnings The f ollowin g warnings are f or the setup , use, gro unding, maintenance , and repair of this equipment. The excla ma- tion point symbol alerts you to a gener al warning and the hazard symbol r ef ers to pr ocedure-spe cific risk. When these symbols appear in the body of t his manual or on warning labels, r ef er back[...]

Warnings 313643G 3[...]

Installation 4 313643G Installation NO TE: R efe rence number s and letters in parentheses in the te xt ref er to the ca llouts in the figures and in th e par ts d ra wing. Gr ounding The equipment m ust be ground ed. Grounding reduce s the risk of static and electric shock b y provid ing an escape wire f or the electrical current du e to static b [...]

Installation 313643G 5 Install the Agitator 1. Due to v ariability in dr um heights the lowest set of bl ades ma y contact the bottom of the drum. If the bung adapter will not fully seat, or if resistance is felt when installing the agitator , mov e the b lades up the shaft. T o mov e th e bl ades, loosen the setscre w on the hub an d slide the as [...]

Operation 6 313643G Operation Pressure Relief Pr ocedure 1. T ur n off the air regulator and close ma in air shutoff va lve . 2. Disconnect the a ir line from the motor air inlet. Operate the Agitator 1. Fill the fluid supply container . 2. Star t the agitator and run it slowly . 3. Use the needle valv e (11) to regulate the agitato r speed. Set th[...]

Repair 313643G 7 Repair Flush the Air Motor If the moto r is sluggish or inefficient, f lush it with non-flammab le solv ent in a w ell-v entilated area. 1. Fo llow the Pressure Relief Pro cedure . See page 6. 2. Add sev eral teaspoons of so lv ent, or spra y the sol- v ent directly into the mot or . 3. Rotate the shaft by hand in both directions f[...]

Parts 8 313643G Pa r t s 1 T orque to 65 in-lb (7.3 N•m) 1 1 2 3 4 7 6 8 8 9 11 12 13 15 T orque to 80 in-lb (9 N•m) 2 2 ti14649a 1 7 16[...]

Parts 313643G 9 P art No/Description * Air Motor Repair Kits ma y be purchase d separately . Order Kit 207 335 for Model 24C728 (l ow viscosity) or Kit 224954 f or Model 24C7 29 (high viscosity). Dimensions 2 in. Bung Adapter 1-1/2 in. Bu ng Adapter Ref. No. P ar t No. Description Qty . 1* 16A871 111310 MO T OR, ai r Low Viscosity (Model 24C728) Hi[...]

Technica l Data 10 313643G T echnical Data * T ested in water to ISO 9614-2. Maximum working pressure 100 psi (0.70 MP a, 7.0 bar) Maximum recom mended agita tor speed . . . . . . . . . . . . . 500 r pm Air consumption at 400 r pm with 100 psi (0.7 MP a, 7 bar) air inlet pressure Model 24C 728 (low viscosity) . . . . . . . . . . . . . . . . . . Mod[...]

Technical Data 313643G 11[...]

All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. Original instructions. T his manual contains English. MM 313643 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Kore[...]