Global Machinery Company RBS10 инструкция обслуживания

RBS10 MAN RBS10 10/01 INSTRUCTION MANU AL 245mm Band Sa w • Melbourne • Perth • Auckland • Hong K ong • Shanghai • T aipei • New Y ork • V erona • London • P aris[...]

Contents W arr anty 2 Introduction 3 Specifications 3 Safety instructions 3 Additional safety rules f or saws 5 Unpacking 6 Assembly 6 Know y our product 7 Setting up 8 Operation 10 Maintenance 10 Full 2 Y ears Home Use W arr anty Whilst every effort is made to ensure your complete satisfaction with this tool, occasionally , due to the mass manufac[...]

Specifications Nominal voltage: 230 – 240 V ac~ 50 Hz Wattage: 370W Band speed: 700m/min Dimensions: 860 mm x 420 mm x 530 mm Working table: 340 mm x 335 mm (adjustable between 0 - 45º) T able height from floor: 370 mm Width of throat: 245 mm Max.cutting height: 100 mm Saw blade length: 1,712 mm Saw blade width: 10 mm (3 to 12.7mm) Gross weight:[...]

2. Consider the environment in which you are working. Do not use power tools in damp or wet locations. K eep the work area well lit. Do not expose power tools to rain and high humidity. Do not use power tools in the presence of flammable liquids or gases . 3. Keep visitors away from the work area. All visitors and onlookers , especially children an[...]

replaced by an authorised service facility. Do not use a tool if the switch does not turn the tool on and off correctly. 20. Guard against electric shock. Prevent body contact with grounded objects such as water pipes, radiators , ranges and refrigerator enclosures. 21. Use only approved parts. When servicing, use only identical replacement parts. [...]

Unpacking Due to modern mass production techniques, it is unlik ely that your GMC Power T ool is f aulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Assembly The Band Saw is shipped partly [...]

Know y our product 1. Saw blade 2. Upper wheel housing 3. Saw band tensioning knob 4. Lower wheel housing 5. Saw band tensioning knob 6. Motor shaft (not shown) 7. Drive belt (not shown) 8. ON button 9. OFF button 10. T able insert 11. Rip fence 12. Rip fence scale 13. Rip fence guide 14. Rip fence guide handle 15. T able trunnion 16. T able trunni[...]

Setting up Centring the table 1. Loosen the screws holding the table trunnion bracket 2. Move the table until the saw blade is positioned in the centre of the table insert 3. Tighten the bracket screws ensuring that the table does not move . Setting the table squar e with the saw blade 1. Loosen the table tilt-securing knob . 2. Adjust the he x hea[...]

Changing the saw band W arning. Ensure that the mains plug is removed from the power socket The saw is supplied with a general-purpose woodcutting blade . 1. T o change the blade , first remove the rip fence scale . 2. Slacken the blade tension by rotating anti-clockwise the blade tensioning knob on the top of the upper wheel housing. 3. Open the d[...]

Operation Switching on and o ff 1. Connect the plug to the power supply. 2. Depress the ON button. 3. T o switch off, depress the OFF button. NOTE. 1. The saw must be connected to an earthed outlet and should be operated on a residual current device (RCD) of 30 mA capacity. 2. Extension leads must have a minimum lead cross section of 3 x 0.75 mm (2[...]

Carefully read the entire Instruction Manual before using this product. Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 (Australia) or 0800 445 721 (New Zealand) When you make your call, please have the following information at hand: • GMC Product Type • GMC Product Code A GMC Service Engineer wil[...]