Global Machinery Company BG150A инструкция обслуживания

• Melbourne • Perth • Auckland • Hong K ong • Shanghai • T aipei • New Y ork • V erona • London • Paris INSTRUCTION MANU AL 1/5 HP / 2/5 HP / 2/3 HP / 1/2 HP Bench Grinders 031222 ED8 DR BG125A BG150A BG200A NTS2000A[...]

Contents W arr anty 2 Introduction 3 Environment al protection 3 Description of s ymbols 3 Specifications 3 Safety instructions 4 A dditional safety rules f or bench grinders 6 Unpacking 6 Connecting to the po wer supply 6 Know y our product 7 Fitting and adjusting the ey e shields and brackets 8 Fitting the tool r ests 8 Bench mounting the grinder[...]

Dear Customer If you require any help with your product, whether it is a W arranty claim, spare part or user inf ormation: Please phone our Help Line for an immediate response . Phone 1300 880 001 in Australia or 0800 445 721 in New Zealand. Introduction Y our new GMC power tool will more than satisfy your e xpectations . It has been manufactured u[...]

Safety instructions The tool must be used only for the prescribed purpose . Any uses other than those mentioned in this manual will be considered a case of misuse . The user and not the manufacturer shall be liable f or any damage or injury resulting from such cases of misuse . To use this tool properly , you must observe the safety regulations, th[...]

8. Use safety accessories. Safety glasses and earmuff s should always be worn. A face or dust mask is also required. 9. Connect dust extr action equipment. If devices are provided for the connection o f dust extraction and collection facilities , ensure that these are connected and properly used. 10. Do not abuse the po wer cord. Never pull the cor[...]

A dditional safety rules f or bench grinders • Always remove the plug from the mains socket before making any adjustments or maintenance , including changing the wheel. • Always wear eye protection and check that the eye shields on the grinder are properly adjusted. • Always turn the grinder off when it is not in use and never leave it unatte[...]

7 Know y our product Before using the bench grinder , familiarise yourself with all the operating features and safety requirements. The GMC Bench Grinders are designed for light to moderate duty applications in a home environment. They are not intended for use by trade persons . They are ideal f or sharpening tools such as drill bits and chisels . [...]

8 Caution. During use it is important not to overload the grinder . The grinder should run at close to full speed. If you are applying too much pressure the grinder will start to slow down. Under these conditions, remove the part being ground and allow the grinder to return to full speed. Re-apply the part to the grinder , but with a little less fo[...]

section under the screw head fits into the slot of the tool rest. Fit the star washer and then the large flat washer . 3. Fit the plastic coated thumb nut to the screw and tighten the nut sufficiently to support the tool rest but still allowing the tool rest to slide inward and outwards. 4. Slide the tool rest to within a max of 1.5mm from the whee[...]

Changing a grinding wheel (high speed wheel) Important. Prior to changing a wheel, ensure the grinder is turned off and the power plug is removed from the socket. Make sure that the replacement wheel is rated at 3000RPM or higher . 1. Remove the retaining screw and take o ff the tool rest (7). 2. Remove the retaining screw and take o ff the eye shi[...]

1. Drain all the water from the bath (10). 2. Remove the two securing screws at the top of the bath. 3. Loosen, but do not remove the lower retaining screw . 4. Push the top clips of the bath clear of housing and then lower the bath clear of the housing. 5. Using an 18mm spanner , remove the wheel retaining nut by turning the nut in an anti-clockwi[...]

Grinder adjustments During the life of the grinder some adjustments are required to maintain a safe working environment. Please ensure the following: • Always adjust the eye shields to the most comfortable and most effective angle to suit the task being performed. • As the wheels wear , the top eye shield bracket must be adjusted to ensure the [...]

Carefully read the entire Instruction Manual before using this product. Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 (Australia) or 0800 445 721 (New Zealand) When you make your call, please have the following information at hand: • GMC Product Type • GMC Product Code A GMC Service Engineer wil[...]