Gemini GEM-RP8 инструкция обслуживания

ARME D COM PUT ERI ZED SE CURI TY SY STE M STAT US I H 1 2 3 4 5 6 7 8 A 1 2 3 B 4 5 6 C 7 8 9 0 E F G J OPERA TING GUIDE for your GEM-RP8 KEYP AD © NAPCO 2003 DESIGN PATS. PENDING OI219E 7/03[...]

Congratulations on your p urchase of an advanced GEMINI-RP8 keyp ad. Meticulously deve loped by a leading manufacturer of state-of-the-art security products, this sy stem will provide y ou with unprecedented peace-of -mind & incorporates some of the most sophisticated features availab le to day. Above all, it has been designed an extra step, to[...]

3 Important - T est Y our System W eekly! 1 Bell / Batter y Test Test your bell or siren by pressin g A follow ed b y 1 . This will cause the be ll, or siren to s ound for 2 seconds and also initiate a test of the bat tery. 2 Zone Test W alk throughout the premises, opening each protected door or window, and act ivating each motion sens or. C heck [...]

ARME D COM PUT ERI ZED SE CURI TY SY STE M STAT US I H GEMIN I 1 2 3 4 5 6 7 8 A 1 2 3 B 4 5 6 C 7 8 9 0 E F G J 4 Statu s Ligh t will lig ht whe n all zo nes are secure and sy stem is rea dy to be Armed. AC Light will light to indicate that AC Power is present. Troub le Light H will light and the Key pad sound er will puls e to in dicate t hat a s[...]

Arming Your System When Leaving 1 Before arming y our system, make sure the green Status light is ON. T his indicates that all of your prote ctive zones are secure. If any zones are open, the corresponding Zone number will be lit. Secure these zones before proceeding. If any zones cannot be secured, see By passing zones below. 2 Enter your user cod[...]

Protecting Yourself While at Home 1 Before arming y our system, make sure the green Status light is ON. T his indicates that all of your protective zones a re secure. If any zones are open, the co rresponding zone nu mber will be lit. Secure those zones before proceeding. 2 Enter your User Code an d press D . The green Status light w ill go out, an[...]

Emergency Butt ons 7 8 9 G The three sets of emergen cy buttons, if programmed , are alw ays active whether the sy stem is arm ed or disarmed. Discuss these Buttons with your insta ller. The emergency signal w ill only be activate d when the two respective buttons are pressed at the same time. Fire Alarm: Simultaneously press 7 + G to sound a fire [...]

Disarming Your System when Return ing 1 Enter your premises through the Entry/Exit door. The keypad will sound a steady tone t o remind you to disarm the system bef ore y our Entry Delay tim e expi res. 2 Ent er your User Co de and press D . The red Ar m e d light will go out, indicating that the system has been disarmed. Note: If you make a mistak[...]

Preparing a Fire Escape Plan Eve n with the most advanced f ire alarm system, adequate protection requ ires an escape plan. To prepare your pla n, draw floor plans of yo ur building (space is provided on the next page ). Show two exits-a front or back door and a window from each room. (Make sure each window works. You may need a special fire-escape[...]

10 Floorplan Draw a plan of yo ur premises below. FIRE PROTECTION[...]

By pressing A followed by the the appropriate key, (do not press simultaneously ) these special functions and features can be enabled: Easy Arm (when s ystem is di sarmed) The Easy Arm feature a llows the system to be armed by pressing A followed b y 0 . This will allow the easy arming of the system by someone who is not a regular system user. Easy[...]

12 The Control Panel is constantl y monitoring its own components, as well as all critical servic es, such as AC po wer and the telephone line, to insure that it is al ways read y to pro vide the protectio n for which it was designed. W hen a system trouble d oes occur, it will caution you by lighting the TROUBLE H light and beeping the keypad buzz[...]

13 Keypad Beeps or H Flashes Zone light ON System T rouble Condition Action 2 Beeps 2 Fire Trouble A problem has been detecte d in the Fire C ircuit. Call installi ng company for service. 2 Beeps 3 Wir el e s s R ec ei v e r Trouble A problem has been detected with the wireless receiver. Call installi ng company for service. 2 Beeps 4 Wirele ss Re [...]

Your Installer has assigned a User 1 Code wh ich can be used to not only Arm and Disarm the sy stem, but also to enter the User Program Mode, whe re you can program other user codes. T he following explains how you w ill use this code to program or erase additional user codes. Entering the User Program Mode Press A follow e d by 8 and en ter the Us[...]

Ambush Code - In the event that you are forced by an intruder to disarm your system, this special code can be used to disarm the s ystem, and simultaneously send a silent alarm to Central Station. If your sy stem has the Ambush feature enabled, the code assigned as the User 8 code will function as your Ambush Code. Arming / Disarming - Tu rning th [...]

NAPCO LIMITED W A RRANTY THE F OLLOWING STATEMENT IS REQ UIRED BY TH E FCC . This equipmen t generates and uses radio-freq uency energy an d, if not installed and used pr operly, that is, in strict accordance with th e manufacturer's instructions, may cau se interference to radio and tel e visi o n reception. It has been type tested and found [...]