Firstech, LLC. P2WSSR инструкция обслуживания

1 User Manual By Firstech LLC, Version: 1.3 Applicable to the following remote(s) ; P2WSSR (2 Way Spread Spectrum Remote) P2W900FMR (2 Way 90 0 MHz Remote) This device complies w ith Part 15 of the FCC rules. Opera tion is subject to the following conditions; (1) This device may not cause harmful interference. (2) This device may accept any interfe[...]

2 Introduction .............................................................................................................................. ................. 3 Kit(s) Contents .............................................................................................................................. ............ 3 Warranty Coverage ............[...]

3 Introduction Thank you for purchasing a CompuStar Pro system for your vehicle. In order to truly enjoy the benefits of this system, we recommend that you fully review the following manual. Please note that this manual applies to the PRO 2WSSR and 2W9000FMR systems, regardless of whether you purchased the alarm only, starter only or alarm/starter [...]

4 Remote Reference P2WSSR (2-Way Spread Spectrum) Applicable to the following models; - P2WSS-AS (alarm and remote start) - P2WSS-A (alarm w/out remote start) - P2WSS-S (remote start w/out alarm) P2W9000R (2-Way 900MHz) Applicable to the following models; - P2W9000-AS (alarm and remote start) - P2W9000-A (alarm w/out remote start) - P2W9000-S (remo[...]

5 Quick Reference Valet Mode When servicing or loaning your vehicle to others, the CompuStar Pro system should be in Valet mode. Valet mode prevents the system from remote starting and disables all alarm functions. IMPORTANT: While in Valet mode the CompuStar will st i ll lock and unlock power lock systems. The system can be put into valet one of t[...]

6 2 Way Remote Button Functions Button Duration Additional Programming Required Function / Description I 0.5 seconds no Lock/Arm and Unlock/Disarm. 2.5 seconds Option 2-11 Run time extender. Resets remote start and tu rbo run-time while vehicle is remote started. II 0.5 seconds no Aux 1. Triggers the auxiliary 1 output (most commonly used for rear [...]

7 1 Way Remote Button Functions Button Duration Additional Programm ing Required Function / Description 0.5 seconds no Lock/Arm 3.5 seconds no Panic/vehicle locater (fla shes vehicles parking light s and sounds siren and horn). 0.5 seconds no Unlock/Disarm 0.5 seconds no Aux 1. Triggers the auxiliary 1 output (most commonly used for rear defrost o [...]

8 Remote LCD (liquid cryst al display) Diagram and Icons Your remote pager will indicate the status of your vehicle while in range. The unique LCD design will visually display such icons as lock/unlock st atus, remote start confirmation and remaining run-time, impact/shock notification, battery voltage, temperature display and much more. Common Ico[...]

9 Starter Icons – Engine Running This icon will be displaye d while the vehicle is running after it has been re mote started. Start Availability This icon will be displaye d when the vehicle is ready to be r emote-started. If this icon is not displayed, you will not be able to remote -start the vehicle. Timer Mode This icon will be displayed when[...]

10 General System Functions The remote transmitter functions have been predetermined and programmed from the factory. The four button configuration allows for many functions to be performed through a series of tapping, holding and / or multiple presses of buttons. Although CompuStar PRO remotes have numerous button functions and capabilities, pleas[...]

11 Active Lock/Arm and Unlock/Disarm Tap button (I) for 0.5 seconds to lock/arm and unlock/disarm. If your vehicle is locked, tap button (I) to unlock; if your vehicle is unlocked, tap button (I) to lock. IMPORTANT: If the alarm has been triggered (Siren is going off), you must wait until the remote pager has been paged before disarming the alarm ?[...]

12 Activating Reservation Mode STEP 1: While the vehicle is running, place the transmission in neutral, set the emergency / parking brake, and remove pressure from the foot brake. STEP 2: Remove the key from the vehicle’s igniti on. The vehicle’s engine should remain running even after the key has been removed. If the vehicle does not remain ru[...]

13 Tap button (II) for 0.5 seconds to trigger auxiliary output 1. Tap button (III) for 0.5 seconds to trigger auxiliary output 2. The remote will beep once and the aux icon will illuminate in dicating that the auxiliary outputs have been triggered. By default, the system is in secure auxiliary mode, which requires you to tap button (IV) for 0.5 sec[...]

14 Adjusting the shock sensor sensitivity is done at the actual sensor, which is generally mounted somewhere under the vehicle’s dashboard. The higher t he number on the dial means greater sensitivity to impact. The recommended dial setting for most vehicles is somewhere between 2 & 4. If you are testing your sensor, please note that the shoc[...]

15 STEP 1: Enter remote programming mode by holding down buttons (II + III) simultaneously for 2.5 seconds. The remote will beep once and the LCD will read “Pro9” to indicate that you have successfully entered programming mode. STEP 2: Scroll through the remote options by taping button (IV) for 0.5 seconds. To set the alarm clock tap button (IV[...]

16 STEP 4: Enter the first digit of the desired four-digit pass code by knocking on the windshield in fr ont of the RPS the desired number of times. For example, to enter 3, knock on the sensor 3 times (each time you knock the LED will flash RED) then wait. STEP 5: The LED on the RPS will confirm your first num ber by flashing BLUE slowly. Once the[...]

17 Option 4: Will start at the time specified on the 2 way remote once within 24 hours ev ery day. This option requires a cold or hot temperature setting as a safety feature. In o ther words, prior to starting at specified time, the system will only start if it is below the cold temperature settings or above the hot temperature settings. To program[...]

18 Turn Auto Mode off by holding down button (I) a fourth time for 2.5 seconds. The remote will beep twice and the Auto Mode icon will disappear. Anti Jacking Mode The CompuStar systems have a built in mode that woul d require you to keep your remote separate from your key chain. This feature also requires additional labor. Please consult your inst[...]

19 remote has been learned. The P2WSSR can recognize two remotes; 2 two-way remotes or 1 two-way remote and 1 one-way remote . When using 2 two-way remotes, the second remote will need to be re- synced to the antenna prior to operation (see page 10). Remote S t art Error Diagnostic If the remote start fails to start the vehicle, the parking lights [...]

20 Limited Lifetime W arranty Firstech, LLC Warrants to the original purchaser that this product shall b e free of defects in material and workmanship under normal use and circumstances for the period of time that the original owner of this product owns the vehicle in which it is installed; except that the remote controller unit for the perio d of [...]

21 Notes: ___________________________________________________________________________________ ___________________________________________________________________________________ ___________________________________________________________________________________ ___________________________________________________________________________________ ____[...]

22 ___________________________________________________________________________________ ___________________________________________________________________________________ ___________________________________________________________________________________ ___________________________________________________________________________________ ___________[...]

23 www.compustar.com Toll Free: 888-820-3690 21911 68 th Ave S Kent, WA 98032[...]